iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 12215-8:2009/AC:2010

(Corrigendum)

Small craft - Hull construction and scantlings - Part 8: Rudders - Technical Corrigendum 1 (ISO 12215-8:2009/Cor 1:2010)

Small craft - Hull construction and scantlings - Part 8: Rudders - Technical Corrigendum 1 (ISO 12215-8:2009/Cor 1:2010)

2010-08-24 EMA: Consultant added following e-mail from PM sent to dataservice on 2010-08-23.

Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 8: Ruder (ISO 12215-8:2009/Cor 1:2010)

Petits navires - Construction de coques et échantillonnage - Partie 8: Gouvernails - Rectificatif technique 1 (ISO 12215-8:2009/Cor 1:2010)

Mala plovila - Konstrukcija trupa in zahtevane lastnosti - 8. del: Krmila - Tehnični popravek 1 (ISO 12215-8:2009/Cor 1:2010)

Ta del ISO 12215 podaja zahteve glede zahtevanih lastnosti krmil, nameščenih na mala plovila z dolžino trupa, LH, do 24 m, merjenega v skladu z ISO 8666. Velja le za enotrupna plovila. Ta del ISO 12215 ne podaja zahtev glede značilnosti krmil, potrebnih za brezhibno zmožnost krmarjenja. Ta del ISO 12215 obravnava zgolj tlačne obremenitve krmilo, ki ga povzroči manevriranje plovila. Obremenitve krmila ali njegovega skega, kjer je nameščen in jih povzroči nasedanje ali dokiranje, kadar je to ustrezno, so zunaj področja uporabe in jih je treba obravnavati ločeno.

General Information

Status
Withdrawn
Publication Date
14-Sep-2010
Withdrawal Date
02-Oct-2018
ICS
47.020.10 - Hulls and their structure elements
47.080 - Small craft
Technical Committee
CEN/SS T01 - Shipbuilding and maritime structures
Drafting Committee
CEN/SS T01 - Shipbuilding and maritime structures
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
03-Oct-2018
Directive
2003/44/EC - Approximation of the laws, regulations and administrative provisions of the Member States relating to recreational craft
2013/53/EU - Directive 2013/53/EU of the European Parliament and of the Council of 20 November 2013 on recreational craft and personal watercraft and repealing Directive 94/25/EC
94/25/EC - Directive 94/25/EC of the European Parliament and of the Council of 16 June 1994 on the approximation of the laws, regulations and administrative provisions of the Member States relating to recreational craft
Mandate
M/075 - Revised mandate to CEN for standardization in the field of recreational craft
Ref Project
SIST EN ISO 12215-8:2009/AC:2011 - Small craft - Hull construction and scantlings - Part 8: Rudders - Technical Corrigendum 1 (ISO 12215-8:2009/Cor 1:2010)

Relations

Replaced By
EN ISO 12215-8:2018 - Small craft - Hull construction and scantlings - Part 8: Rudders (ISO 12215-8:2009, including Cor 1:2010)
Effective Date
08-Jun-2022
Corrects
EN ISO 12215-8:2009 - Small craft - Hull construction and scantlings - Part 8: Rudders (ISO 12215-8:2009)
Effective Date
08-Jun-2022

Buy Standard

EN ISO 12215-8:2009/AC:2011EN ISO 12215-8:2009/AC:2011
PreviousNext
Corrigendum
EN ISO 12215-8:2009/AC:2011
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 8: Ruder (ISO 12215-8:2009/Cor 1:2010)Petits navires - Construction de coques et échantillonnage - Partie 8: Gouvernails - Rectificatif technique 1 (ISO 12215-8:2009/Cor 1:2010)Small craft - Hull construction and scantlings - Part 8: Rudders - Technical Corrigendum 1 (ISO 12215-8:2009/Cor 1:2010)47.080ýROQLSmall craft47.020.10Ladijski trupi in njihovi konstrukcijski elementiHulls and their structure elementsICS:Ta slovenski standard je istoveten z:EN ISO 12215-8:2009/AC:2010SIST EN ISO 12215-8:2009/AC:2011en,fr,de01-januar-2011SIST EN ISO 12215-8:2009/AC:2011SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 12215-8:2009/AC
September 2010
Septembre 2010
September 2010 ICS 47.080 English version Version Française Deutsche Fassung
Small craft - Hull construction and scantlings - Part 8: Rudders - Technical Corrigendum 1 (ISO 12215-8:2009/Cor 1:2010)
Petits navires - Construction de coques et échantillonnage - Partie 8: Gouvernails - Rectificatif technique 1 (ISO 12215-8:2009/Cor 1:2010)
Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 8: Ruder (ISO 12215-8:2009/Cor 1:2010) This corrigendum becomes effective on 15 September 2010 for incorporation in the three official language versions of the EN.
Ce corrigendum prendra effet le 15 septembre 2010 pour incorporation dans les trois versions linguistiques officielles de la EN.
Die Berichtigung tritt am 15.September 2010 zur Einarbeitung in die drei offiziellen Sprachfassungen der EN in Kraft.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 12215-7:2020(Main)
Small craft - Hull construction and scantlings - Part 7: Determination of loads for multihulls and of their local scantlings using ISO 12215-5 (ISO 12215-7:2020)
SIST EN ISO 12215-7:2021

This document defines the dimensions, local design pressures and global loads acting on multihull craft with a hull length (LH) or load line length of up to 24 m (see Note). It considers all parts of the craft that are assumed watertight or weathertight when assessing stability, freeboard and buoyancy in accordance with ISO 12217 (all parts). Scantlings corresponding to the local design pressures are then assessed using ISO 12215-5.
NOTE       The load line length is defined in the OMI "International Load Lines Convention 1966/2005", it can be smaller than LH for craft with overhangs. This length also sets up at 24 m the lower limit of several IMO conventions.
This document is applicable to multihulls built from the same materials as in ISO 12215-5, in intact condition, and of the two following types:
—          recreational craft, including recreational charter vessels;
—          commercial craft and workboats.
It is not applicable to multihull racing craft designed only for professional racing.
This document is applicable to the structures supporting windows, portlights, hatches, deadlights and doors.
For the complete scantlings of the craft, this document is intended to be used in conjunction with ISO 12215-8 for rudders, ISO 12215-9 for appendages of sailing craft and ISO 12215-10 for rig loads and rig attachment in sailing craft. ISO 12215-6 can be used for additional details.
Throughout this document, unless otherwise specified, dimensions are in (m), areas in (m2), masses in (kg), forces in (N), moments in (Nm), Pressures in (kN/m2) (1 kN/m2 = 1 kPa), stresses and elastic modulus in (N/mm2) (1 N/mm2 = 1 MPa).

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12215-5:2019(Main)
Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls, design stresses, scantlings determination (ISO 12215-5:2019, Corrected version 2024-03)
SIST EN ISO 12215-5:2019

This document defines the dimensions, design local pressures, mechanical properties and design stresses for the scantlings determination of monohull small craft with a hull length (LH) or a load line length (see NOTE 1) of up to 24 m. It considers all parts of the craft that are assumed to be watertight or weathertight when assessing stability, freeboard and buoyancy in accordance with ISO 12217.
NOTE 1    The load line length is defined in the IMO "International Load Lines Convention 1966/2005", it can be larger than LH for craft with overhangs. This length also sets up at 24 m the lower limit of several IMO conventions.
The main core of this document determines the local design pressures and stresses for monohulls and details the possible scantlings methods derived from these pressures and stresses, both for monohulls and multihulls (see NOTE 2). The assessment process requires, where relevant, the application of Annexes.
This document is applicable to small craft, in intact condition, of the two following types:
—          recreational craft, including recreational charter vessels;
—          small commercial craft and workboats, see Clause 12 and Annex J.
It is not applicable to racing craft designed only for professional racing.
NOTE 2    Local pressures and stresses for multihulls are given in ISO 12215-7.
This document is applicable to the structures supporting windows, portlights, hatches, deadlights, and doors.
For the complete scantlings of the craft, this document is intended to be used with ISO 12215-8 for rudders, ISO 12215-9 for appendages and ISO 12215-10 for rig loads and rig attachments.
This document covers small craft built from the following materials:
—          fibre-reinforced plastics, either in single skin or sandwich construction;
—          aluminium or steel alloys;
—          glued wood or plywood (single skin or sandwich), excluding traditional wood construction;
—          non-reinforced plastics for craft with a hull length less than 6 m (see Annex D).
Throughout this document, unless otherwise specified, dimensions are in (m), areas in (m2), masses in (kg), forces in (N), moments in (N.m), pressures in kN/m2 (1 kN/m2 = 1  kPa), stresses and elastic modulus in N/mm2 (1 N/mm2 = 1 Mpa). Max(a;b;c) means that the required value is the maximum of a, b, and c; and min(d;e;f) means that the required value is the minimum of d, e, and f.

  • Standard
    136 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12215-8:2018(Main)
Small craft - Hull construction and scantlings - Part 8: Rudders (ISO 12215-8:2009, including Cor 1:2010)
SIST EN ISO 12215-8:2018

ISO 12215-8:2009 gives requirements on the scantlings of rudders fitted to small craft with a length of hull of up to 24 m, measured according to ISO 8666. It applies only to monohulls.
ISO 12215-8:2009 does not give requirements on rudder characteristics required for proper steering capabilities.
ISO 12215-8:2009 only considers pressure loads on the rudder due to craft manoeuvring. Loads on the rudder or its skeg, where fitted, induced by grounding or docking, where relevant, are out of scope and need to be considered separately.
Scantlings derived from ISO 12215-8:2009 are primarily intended to apply to recreational craft including charter craft.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 12217-2(Main)
Small craft - Stability and buoyancy assessment and categorization - Part 2: -Sailing boats of hull length greater than or equal to 6 m (ISO/DIS 12217-2:2020)
oSIST prEN ISO 12217-2:2021

This document specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of boats susceptible to swamping are also encompassed.
The evaluation of stability and buoyancy properties using this document will enable the boat to be assigned to a design category (A, B, C or D) appropriate to its design and maximum load.
This document is principally applicable to boats propelled primarily by sail (even if fitted with an auxiliary engine) of 6 m up to and including 24 m hull length. However, it can also be applied to boats less than 6 m if they are habitable multihulls or can be applied if they do not attain the desired design category specified in ISO 12217‑3 and they are decked and have quick-draining recesses which comply with ISO 11812.
In relation to habitable multihulls, this document includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation.
This document excludes:
—    inflatable and rigid-inflatable boats covered by the ISO 6185 series, except for references made in the ISO 6185 series to specific clauses of the ISO 12217 series;
—    gondolas and pedalos;
—    surfboards including sailing surfboards; and
—    hydrofoils and foil stabilized boats when not operating in the displacement mode.
NOTE       Displacement mode means that the boat is only supported by hydrostatic forces.
It does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.

  • Draft
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 12217-3(Main)
Small craft - Stability and buoyancy assessment and categorization - Part 3: Boats of hull length less than 6 m (ISO/DIS 12217-3:2020)
oSIST prEN ISO 12217-3:2021

This document specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of craft susceptible to swamping are also encompassed.
The evaluation of stability and buoyancy properties using this document will enable the boat to be assigned to a design category (C or D) appropriate to its design and maximum load.
This document is applicable to boats of hull length less than 6 m, whether propelled by human or mechanical power, except habitable sailing multihulls. Boats of hull length less than 6 m which are fitted with a full deck and quick-draining cockpit(s) complying with ISO 11812 can alternatively be assessed using ISO 12217‑1 or ISO 12217‑2 (for non-sailing and sailing boats, respectively), in which case higher design categories can be assigned.
In relation to habitable multihulls, this document includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation.
This document excludes:
—    inflatable and rigid-inflatable boats covered by the ISO 6185 series, except for references made in the ISO 6185 series to specific clauses of the ISO 12217 series;
—    personal watercraft covered by ISO 13590 and other similar powered craft;
—    aquatic toys;
—    canoes and kayaks;
—    gondolas and pedalos;
—    sailing surfboards;
—    surfboards, including powered surfboards;
—    hydrofoils, foil stabilized boats and hovercraft when not operating in the displacement mode; and
—    submersibles.
NOTE       Displacement mode means that the boat is only supported by hydrostatic forces.
It does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.

  • Draft
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17928-1:2024(Main)
Gas infrastructure - Injection stations - Part 1: General requirements
kSIST FprEN 17928-1:2024

This document establishes the functional requirements for stations for the injection of biomethane, substitute natural gas (SNG) and hydrogen into gas transmission and distribution systems operated with gases (natural gas, biomethane, SNG, hydrogen, gas mixtures) in accordance with European technical rules that ensure the interoperability of systems.
Figure 1 describes the general approach including all the relevant functions that can be installed in different configurations. The injection of Hydrogen is covered separately in EN 17928-3:2024.
This document also applies to refeeding stations that feed such gases back into upstream gas supply networks; see Figure 2.
This document represents the state of the art at the time of its preparation.
This document does not apply to injection stations operating prior to the publication of this document.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in national legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 (all parts) gives:
—   legislation/regulations applicable in a member state;
—   if appropriate, more restrictive national requirements;
—   a national contact point for the latest information.

  • Draft
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13237:2024(Main)
Potentially explosive atmospheres - Terms and definitions for equipment and protective systems intended for use in potentially explosive atmospheres
oSIST prEN 13237:2022

This document specifies terms and definitions (vocabulary) to be used in suitable standards dealing with equipment and protective systems intended for use in potentially explosive atmospheres within the scope of Directive 2014/34/EU.
NOTE   Terms and definitions avoid misunderstandings that are important in relation to the essential health and safety requirements of Directive 2014/34/EU.

  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19085-7:2024(Main)
Woodworking machines - Safety - Part 7: Surface planing, thickness planing and combined surface/thickness planing machines (ISO 19085-7:2024)
kSIST FprEN ISO 19085-7:2024

This document specifies the safety requirements and measures for
—     surface planing machines, also called jointers,
—     thickness planing machines, also called planers or single surface planers, and
—     combined surface/thickness planing machines
with fixed cutter block position, with an integrated feed in thickness planing mode, with or without demountable power feed device in planing mode, with manual loading and/or unloading of the workpiece, and capable of continuous production use, altogether referred to as “machines”.
The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2).
This document deals with all significant hazards, hazardous situations and events as listed in Annex A relevant to the machines when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer. Reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account.
This document is also applicable to surface planing machines and combined surface/thickness planing machines fitted with an optional mortising device, whose hazards have been dealt with.
This document does not apply to:
a)       machines with more than one cutter block;
b)       machines with a mortising unit driven by a separate motor;
c)        machines where the cutter block is adjustable for depth of cut setting in thickness planing mode;
d)       machines where the conversion from planing to thickness planing mode or vice versa is achieved by mounting or demounting parts/units;
e)       machines where surface planing and thickness planing can be performed at the same time;
f)         machines intended for use in potentially explosive atmosphere;
g)       machines manufactured prior to the publication of this document.

  • Draft
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 2350:2024(Main)
Aerospace series - Circuit breakers - Technical specification
kSIST FprEN 2350:2024
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 927-15:2024(Main)
Paints and varnishes - Coating materials and coating systems for exterior wood - Part 15: Assessment of bleeding of coloured wood extractives through a coating by means of a water immersion test
kSIST-TS FprCEN/TS 927-15:2024

This document specifies a test method using water immersion test for assessing the bleeding of coloured wood extractives through a coating. Leachates of coated and uncoated wood are collected after the immersion procedure and their colour is compared. The colour of the coated wood before and after immersion tests is also compared. This document does not specify acceptance values for colour differences that can be tolerated and it is not applicable to staining caused by knots for which there is a different test method (see EN 927 7).
NOTE   The method has been developed for oak and chestnut wood and might be applicable for other wood substrates containing water soluble extractives.

  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day