EN 10246-3:1999
(Main)Non-destructive testing of steel tubes - Part 3: Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections
Non-destructive testing of steel tubes - Part 3: Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections
This Part of EN 10246 specifies the requirements for automatic eddy current testing of seamless and welded tubes with the exception of submerged arc-welded (SAW) tubes for the detection of imperfections. The standard specifies acceptance levels, calibration procedures and gives guidance on the limitations of the tests. This Part of EN 10246 is applicable to the inspection of tubes with an outside diameter equal to or greater than 4 mm. European Standard EN 10246 "Non-destructive testing of steel tubes" comprises the Parts shown in Annex A.
Zerstörungsfreie Prüfung von Stahlrohren - Teil 3: Automatische Wirbelstromprüfung nathloser und geschweißter (ausgenommen unterpulvergeschweißter) Stahlrohre zum Nachweis von Fehlern
Dieser Teil der EN 10246 legt die Anforderungen an die automatische Wirbelstromprüfung nahtloser und geschweißter Stahlrohre, mit Ausnahme unterpulvergeschweißter (SAW-) Rohre, zum Nachweis von Fehlern fest. Die Norm enthält Festlegungen über Zulässigkeitsklassen und die Einstellung der Prüfanlagen sowie Hinweise zu den Grenzen der Prüfverfahren. Dieser Teil der EN 10246 ist anwendbar für die Prüfung von Rohren mit einem Außendurchmesser ab 4 mm. Die Europäische Norm EN 10246 "Zerstörungsfreie Prüfung von Stahlrohren" besteht aus den in Anhang A angegebenen Teilen.
Essais non destructifs des tubes en acier - Partie 3: contrôle automatique par courants de Foucault pour la détection des imperfections des tubes en acier sans soudure et soudés (sauf à l'arc immergé sous flux en poudre)
La présente partie de la l'EN 10246 spécifie les prescriptions relatives au contrôle automatique des tubes en acier sans soudure et soudés (sauf à l'arc immergé sous flux en poudre), pour la détection d'imperfections. La norme spécifie des niveaux de sévérité, des procédures d'étalonnage et donne des informations sur les limitations de cet essai. Elle s'applique au contrôle de tubes dont le diamètre extérieur est égal ou supérieur à 4 mm. Les parties de la norme européenne EN 10246 "Essais non destructifs des tubes en acier" sont données en annexe A.
Neporušitveno preskušanje jeklenih cevi - 3. del: Ugotavljanje napak jeklenih cevi, nevarjenih in varjenih (razen obločno varjenih pod praškom), z avtomatsko preiskavo z vrtinčnimi tokovi
General Information
- Status
- Withdrawn
- Publication Date
- 16-Nov-1999
- Withdrawal Date
- 31-Mar-2011
- Technical Committee
- ECISS/TC 110 - Steel tubes, and iron and steel fittings
- Drafting Committee
- ECISS/TC 29/SC 10 - Non-destructive testing
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 01-Apr-2011
- Completion Date
- 01-Apr-2011
Relations
- Effective Date
- 08-Jun-2022
Frequently Asked Questions
EN 10246-3:1999 is a standard published by the European Committee for Standardization (CEN). Its full title is "Non-destructive testing of steel tubes - Part 3: Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections". This standard covers: This Part of EN 10246 specifies the requirements for automatic eddy current testing of seamless and welded tubes with the exception of submerged arc-welded (SAW) tubes for the detection of imperfections. The standard specifies acceptance levels, calibration procedures and gives guidance on the limitations of the tests. This Part of EN 10246 is applicable to the inspection of tubes with an outside diameter equal to or greater than 4 mm. European Standard EN 10246 "Non-destructive testing of steel tubes" comprises the Parts shown in Annex A.
This Part of EN 10246 specifies the requirements for automatic eddy current testing of seamless and welded tubes with the exception of submerged arc-welded (SAW) tubes for the detection of imperfections. The standard specifies acceptance levels, calibration procedures and gives guidance on the limitations of the tests. This Part of EN 10246 is applicable to the inspection of tubes with an outside diameter equal to or greater than 4 mm. European Standard EN 10246 "Non-destructive testing of steel tubes" comprises the Parts shown in Annex A.
EN 10246-3:1999 is classified under the following ICS (International Classification for Standards) categories: 23.040.10 - Iron and steel pipes; 77.040.20 - Non-destructive testing of metals. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 10246-3:1999 has the following relationships with other standards: It is inter standard links to EN ISO 10893-2:2011. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 10246-3:1999 is associated with the following European legislation: EU Directives/Regulations: 97/23/EC; Standardization Mandates: M/005, M/071. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 10246-3:1999 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.WRPDWVNRZerstörungsfreie Prüfung von Stahlrohren - Teil 3: Automatische Wirbelstromprüfung nathloser und geschweißter (ausgenommen unterpulvergeschweißter) Stahlrohre zum Nachweis von FehlernEssais non destructifs des tubes en acier - Partie 3: contrôle automatique par courants de Foucault pour la détection des imperfections des tubes en acier sans soudure et soudés (sauf a l'arc immergé sous flux en poudre)Non-destructive testing of steel tubes - Part 3: Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...