EN ISO 12543-5:2011

SLOVENSKI STANDARD
01-januar-2012
1DGRPHãþD
SIST EN ISO 12543-5:1999
Steklo v gradbeništvu - Lepljeno steklo in lepljeno varnostno steklo - 5. del:
Dimenzije in obdelava robov (ISO 12543-5:2011)
Glass in building - Laminated glass and laminated safety glass - Part 5: Dimensions and
edge finishing (ISO 12543-5:2011)
Glas im Bauwesen - Verbundglas und Verbund- Sicherheitsglas - Teil 5: Maße und
Kantenbearbeitung (ISO 12543-5:2011)
Verre dans la construction - Verre feuilleté et verre feuilleté de sécurité - Partie 5:
Dimensions et façonnage des bords (ISO 12543-5:2011)
Ta slovenski standard je istoveten z: EN ISO 12543-5:2011
ICS:
81.040.20 Steklo v gradbeništvu Glass in building
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 12543-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2011
ICS 81.040.20 Supersedes EN ISO 12543-5:1998
English Version
Glass in building - Laminated glass and laminated safety glass -
Part 5: Dimensions and edge finishing (ISO 12543-5:2011)
Verre dans la construction - Verre feuilleté et verre feuilleté Glas im Bauwesen - Verbundglas und Verbund-
de sécurité - Partie 5: Dimensions et façonnage des bords Sicherheitsglas - Teil 5: Maße und Kantenbearbeitung (ISO
(ISO 12543-5:2011) 12543-5:2011)
This European Standard was approved by CEN on 6 August 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12543-5:2011: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (EN ISO 12543-5:2011) has been prepared by Technical Committee ISO/TC 160 "Glass in
building" in collaboration with Technical Committee CEN/TC 129 “Glass in building” the secretariat of which is
held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2012, and conflicting national standards shall be withdrawn
at the latest by February 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12543-5:1998.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 12543-5:2011 has been approved by CEN as a EN ISO 12543-5:2011 without any
modification.
INTERNATIONAL ISO
STANDARD 12543-5
Second edition
2011-08-15
Glass in building — Laminated glass and
laminated safety glass —
Part 5:
Dimensions and edge finishing
Verre dans la construction — Verre feuilleté et verre feuilleté de
sécurité —
Partie 5: Dimensions et façonnage des bords

Reference number
ISO 12543-5:2011(E)
©
ISO 2011
ISO 12543-5:2011(E)
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

ISO 12543-5:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12543-5 was prepared by Technical Committee ISO/TC 160, Glass in building, Subcommittee SC 1,
Product considerations.
This second edition cancels and replaces the first edition (ISO 12543-5:1998), which has been technically
revised.
ISO 12543 consists of the following parts, under the general title Glass in building — Laminated glass and
laminated safety glass:
⎯ Part 1: Definitions and description of component parts
⎯ Part 2: Laminated safety glass
⎯ Part 3: Laminated glass
⎯ Part 4: Test methods for durability
⎯ Part 5: Dimensions and edge finishing
⎯ Part 6: Appearance
INTERNATIONAL STANDARD ISO 12543-5:2011(E)

Glass in building — Laminated glass and laminated safety
glass —
Part 5:
Dimensions and edge finishing
1 Scope
This part of ISO 12543 specifies dimensions, limit deviations and edge finishes of laminated glass and
laminated safety glass for use in building.
This part of ISO 12543 is not applicable to panes having an area less than 0,05 m .
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 12543-1, Glass in building — Laminated glass and laminated safety glass — Part 1: Definitions and
description of component parts
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 12543-1 and the following apply.
3.1
displacement
d
misalignment at any one edge of the constituent glass panes or plastic glazing sheet material making up the
laminated glass
See Figure 2.
4 Dimensions and limit deviations
4.1 Thickness
4.1.1 Nominal thickness
The nominal thickness of laminated glass shall be the sum of the nominal thicknesses of the constituent
panes of glass, plastic glazing sheet material and the interlayers.
ISO 12543-5:2011(E)
4.1.2 Limit deviation on thickness
4.1.2.1 Limit deviation on thickness of folio laminated products
The limit deviations on thickness of laminated glass shall not exceed the sum of the limit deviations of the
constituent glass panes specified in the basic products standards; see ISO 12543-1:2011, Annex A.
NOTE 1 For the appropriate CEN standards, see ISO 12543-1:2011, Annex B.
If the total interlayer thickness is less than or equal to 2 mm, an additional limit deviation of ±0,1 mm applies. If
the total interlayer thickness is greater than 2 mm, an additional limit deviation of ±0,2 mm shall apply.
The thickness limit deviation for plastic glazing sheet material shall be assumed to be the same as a float
glass of the same nominal thickness.
NOTE 2 If the plastic glazing sheet material is covered by a standard, the actual limit deviations on thickness ca
...