EN 1395-3:2007
(Main)Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 3: Arc spraying
Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 3: Arc spraying
This European Standard specifies requirements for the acceptance inspection of thermal spraying equipment, in this case arc spraying, used to produce thermally sprayed coatings of reproducible quality.
This part should be used in conjunction with EN 1395-1, which includes general requirements and explanations of procedures.
Thermisches Spritzen - Abnahmeprüfungen für Anlagen zum thermischen Spritzen - Teil 3: Lichtbogenspritzen
Dieses Dokument definiert Anforderungen für die Abnahmeprüfung von thermischen Spritzanlagen, in diesem
Fall zum Lichtbogenspritzen, wie sie zur Herstellung von thermisch gespritzten Schichten mit reproduzierbarer
Qualität verwendet werden.
Projection thermique - Contrôle d'acceptation du matériel de projection thermique - Partie 3: Projection à l'arc
La présente Norme européenne spécifie les exigences du contrôle d’acceptation des matériels de projection thermique, et dans le cas présent, de projection à l’arc, utilisés pour obtenir des revêtements de projection thermique de qualité reproductible
Il convient d’utiliser cette partie en liaison avec l’EN 1395-1 qui traite des exigences générales et de l’explication des modes opératoires.
Vroče brizganje – Prevzemni preskusi opreme za vroče brizganje – 3. del: Obločno brizganje
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 3: Arc sprayingEUL]JDQMHProjection thermique - Contrôle d'acceptation du matériel de projection thermique - Partie 3: Projection a l'arcThermisches Spritzen - Abnahmeprüfungen für Anlagen zum thermischen Spritzen - Teil 3: LichtbogenspritzenTa slovenski standard je istoveten z:EN 1395-3:2007SIST EN 1395-3:2007en25.220.20Površinska obdelavaSurface treatmentICS:SIST EN 1395:19991DGRPHãþDSLOVENSKI
STANDARDSIST EN 1395-3:200701-april-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1395-3January 2007ICS 25.220.20Supersedes EN 1395:1996
English VersionThermal spraying - Acceptance inspection of thermal sprayingequipment - Part 3: Arc sprayingProjection thermique - Contrôle d'acceptation du matérielde projection thermique - Partie 3: Projection à l'arcThermisches Spritzen - Abnahmeprüfungen für Anlagenzum thermischen Spritzen - Teil 3: LichtbogenspritzenThis European Standard was approved by CEN on 23 December 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1395-3:2007: E
Inspection report for arc spraying equipment (initial test/retest).6 Bibliography.8
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.