EN ISO 12690:2010

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Metallische und andere anorganische Überzüge - Aufsicht für das thermische Spritzen - Aufgaben und Verantwortung (ISO 12690:2010)Revêtements métalliques et autres revêtements inorganiques - Coordination en projection thermique - Tâches et responsabilités (ISO 12690:2010)Metallic and other inorganic coatings - Thermal spray coordination - Tasks and responsibilities (ISO 12690:2010)25.220.20Površinska obdelavaSurface treatmentICS:Ta slovenski standard je istoveten z:EN ISO 12690:2010SIST EN ISO 12690:2011en,fr,de01-november-2011SIST EN ISO 12690:2011SLOVENSKI
STANDARDSIST EN 13214:20021DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 12690
December 2010 ICS 25.220.20 Supersedes EN 13214:2001English Version
Metallic and other inorganic coatings - Thermal spray coordination - Tasks and responsibilities (ISO 12690:2010)
Revêtements métalliques et autres revêtements inorganiques - Coordination en projection thermique - Tâches et responsabilités (ISO 12690:2010)
Metallische und andere anorganische Überzüge - Aufsicht für das thermische Spritzen - Aufgaben und Verantwortung (ISO 12690:2010) This European Standard was approved by CEN on 14 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 12690:2010: ESIST EN ISO 12690:2011

Reference numberISO 12690:2010(E)© ISO 2010
INTERNATIONAL STANDARD ISO12690First edition2010-12-15Metallic and other inorganic coatings — Thermal spray coordination — Tasks and responsibilities Revêtements métalliques et autres revêtements inorganiques — Coordination en projection thermique — Tâches et responsabilités
ISO 12690:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 12690:2010(E) © ISO 2010 – All rights reserved iii Contents Page Foreword.iv Introduction.v 1 Scope.1 2 Normative references.1 3 Terms and definitions.2 4 Tasks and responsibilities.2 4.1 Quality-related activities.2 4.2 Definition of tasks and responsibilities.3 5 Job description.3 5.1 General.3 5.2 Tasks.3 5.3 Responsibility.3 6 Technical knowledge.4 6.1 General knowledge requirements of all spraying coordination personnel.4 6.2 Specific knowledge requirements of responsible spraying coordination personnel.4 Annex A (informative)
Recommendations of technical knowledge.5 Annex B (normative)
Essential thermal-spraying-related tasks in accordance with ISO 14922 to be considered when appropriate.6 Bibliography.11
ISO 12690:2010(E) iv © ISO 2010 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 12690 was prepared by the European Committee for Standardization (CEN) Technical Committee TC 240, Thermal spraying and thermally sprayed coatings, in collaboration with ISO Technical Committee ISO/TC 107, Metallic and other inorganic coatings in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
ISO 12690:2010(E) © ISO 2010 – All rights reserved v Introduction Thermal spraying is a special process which requires qualified personnel for execution of thermal spraying operations on components or parts. This provides confidence in thermal spraying fabrication and allows reliable performance to be achieved in service during operational time. Coordination personnel are able to coordinate all activities related to thermal spraying, and are responsible for planning, executing, supervising and inspecting.
INTERNATIONAL STANDARD ISO 12690:2010(E) © ISO 2010 – All rights reserved 1 Metallic and other inorganic coatings — Thermal spray coordination — Tasks and responsibilities 1 Scope This International Standard specifies the tasks and responsibilities necessary to ensure the quality of a thermal sprayed coating or a coated component, including the coordination of activities related to thermal spraying. Thermal spraying coordination can be carried out by one or a number of persons within the same company or manufacturing department. The responsibilities of the spraying coordinator are specified by the manufacturer. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6507-1, Metallic materials — Vickers hardness test — Part 1: Test method ISO 6508-1, Metallic materials — Rockwell hardness test — Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) ISO 14918, Thermal spraying — Approval testing of thermal sprayers ISO 14922-1, Thermal spraying — Quality requirements of thermally sprayed structures — Part 1: Guidance for selection and use
ISO 14922-2, Thermal spraying — Quality requirements of thermally sprayed structures — Part 2: Comprehensive quality requirements ISO 14922-3, Thermal spraying — Quality requirements of thermally sprayed structures — Part 3: Standard quality requirements ISO 14922-4, Thermal spraying — Quality requirements of thermally sprayed structures — Part 4: Elementary quality requirements ISO 14923, Thermal spraying — Characterization and testing of thermally sprayed coatings EN 473, Non-destructive testing — Qualification and certification of NDT personnel — General principles EN 571-1, Non-destructive testing — Penetrant testing — Part 1: General principles EN 582, Thermal spraying — Determination of tensile adhesive strength EN 657:2005, Thermal spraying — Terminology, classification SIST EN ISO 12690:2011

ISO 12690:2010(E) 2 © ISO 2010 – All rights reserved EN 1395-1, Thermal spraying — Acceptance inspection for thermal spraying equipment — Part 1: General requirements EN 1395-2, Thermal spraying — Acceptance inspection for thermal spraying equipment — Part 2: Flame spraying including HVOF EN 1395-3, Thermal spraying — Acceptance inspection for thermal spraying equipment — Part 3: Arc spraying EN 1395-4, Thermal spraying — Acceptance inspection for thermal spraying equipment — Part 4: Plasma spraying EN 1395-5, Thermal spraying — Acceptance inspection for thermal spraying equipment — Part 5: Plasma spraying in chambers EN 1395-6, Thermal spraying — Acceptance inspection for thermal spraying equipment — Part 6: Manipulator systems EN 1395-7, Thermal spraying — Acceptance inspection for thermal spraying equipment — Part 7: Powder feed systems EN 15311, Thermal spraying — Components with thermally sprayed coatings — Technical supply conditions EN 15340, Thermal spraying — Determination of shear load resistance of thermally sprayed coatings EN 15648, Thermal spraying — Component related procedure qualification 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 657:2005 and the following apply. 3.1 manufacturing department thermal spraying workshops or sites under the same technical and quality management 3.2 thermal spraying coordinator person who has responsibilities in the manufacturing organization for thermal spraying and thermal-spraying-related activities, whose competence and knowledge has been demonstrated by, for example, education, training and/or relevant manufacturing experience 3.3 thermal spraying inspection inspecting of all activities related to thermal spraying, testing and me
...