EN ISO 14919:2023

SLOVENSKI STANDARD
01-januar-2024
Vroče brizganje - Žice, palice in vrvi za plamensko in obločno brizganje -
Klasifikacija in tehnični dobavni pogoji (ISO 14919:2023)
Thermal spraying - Wires, rods and cords for flame and arc spraying - Classification and
technical supply conditions (ISO 14919:2023)
Thermisches Spritzen - Drähte, Stäbe und Schnüre zum Flammspritzen und
Lichtbogenspritzen - Einteilung - Technische Lieferbedingungen (ISO 14919:2023)
Projection thermique - Fils, baguettes et cordons pour projection thermique à l'arc et au
pistolet dans une flamme - Classification et conditions techniques d'approvisionnement
(ISO 14919:2023)
Ta slovenski standard je istoveten z: EN ISO 14919:2023
ICS:
25.220.20 Površinska obdelava Surface treatment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 14919
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2023
EUROPÄISCHE NORM
ICS 25.220.20 Supersedes EN ISO 14919:2015
English Version
Thermal spraying - Wires, rods and cords for flame and arc
spraying - Classification and technical supply conditions
(ISO 14919:2023)
Projection thermique - Fils, baguettes et cordons pour Thermisches Spritzen - Drähte, Stäbe und Schnüre zum
projection thermique à l'arc et au pistolet dans une Flammspritzen und Lichtbogenspritzen - Einteilung -
flamme - Classification et conditions techniques Technische Lieferbedingungen (ISO 14919:2023)
d'approvisionnement (ISO 14919:2023)
This European Standard was approved by CEN on 5 November 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14919:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 14919:2023) has been prepared by Technical Committee ISO/TC 107 "Metallic
and other inorganic coatings" in collaboration with Technical Committee CEN/TC 240 “Thermal
spraying and thermally sprayed coatings” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2024, and conflicting national standards shall be
withdrawn at the latest by May 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14919:2015.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 14919:2023 has been approved by CEN as EN ISO 14919:2023 without any modification.

INTERNATIONAL ISO
STANDARD 14919
Third edition
2023-10
Thermal spraying — Wires, rods and
cords for flame and arc spraying —
Classification and technical supply
conditions
Projection thermique — Fils, baguettes et cordons pour projection
thermique à l'arc et au pistolet dans une flamme — Classification et
conditions techniques d'approvisionnement
Reference number
ISO 14919:2023(E)
ISO 14919:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 14919:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 1
4.1 Classification according to the manufacturing process and resulting structure . 1
4.2 Classification according to material groups and chemical composition . 2
5 Sizes and tolerances .10
6 Properties .11
6.1 Mechanical properties . 11
6.2 Surface properties . 11
6.3 Workability — Winding of wires .12
7 Designation .12
8 Technical supply conditions .12
8.1 Forms of delivery .12
8.2 Identification . 14
8.3 Packaging and storage . 14
9 Inspection documents .15
iii
ISO 14919:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 107, Metallic and other inorganic coatings,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 240, Thermal spraying and thermally sprayed coatings, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 14919:2015), which has been technically
revised.
The main changes are as follows:
— addition of the alloy ZnAl2, ZnAl4 and ZnAl22 in Table 4.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
INTERNATIONAL STANDARD ISO 14919:2023(E)
Thermal spraying — Wires, rods and cords for flame
and arc spraying — Classification and technical supply
conditions
1 Scope
This document specifies requirements for classification of metal and non-metal wires (solid and cored),
rods, cords processed by means of thermal spraying, especially by arc and flame spraying.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 544:2017, Welding consumables — Technical delivery conditions for filler materials and fluxes — Type
of product, dimensions, tolerances and markings
ISO 10474:2013, Steel and steel products — Inspection documents
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Classification
4.1 Classification according to the manufacturing process and resulting structure
The thermal spray materials are classified according to the manufacturing process and the resulting
structure, as given in Table 1.
Table 1 — Classification of thermal spraying material and resulting structure
Number Term Manufacturing process Structure
1 solid wire/rod metallurgical manufacturing and f
...