EN ISO 14116:2015

SLOVENSKI STANDARD
01-december-2015
1DGRPHãþD
SIST EN ISO 14116:2008
9DURYDOQDREOHND=DãþLWDSUHGXþLQNLSODPHQD0DWHULDOLNRPELQDFLMHPDWHULDORY
LQREOHND]RPHMHQRVWRSQMRJRUOMLYRVWL,62
Protective clothing - Protection against flame - Limited flame spread materials, material
assemblies and clothing (ISO 14116:2015)
Schutzkleidung - Schutz gegen Flammen - Materialien, Materialkombinationen und
Kleidung mit begrenzter Flammenausbreitung (ISO 14116:2015)
Vêtements de protection - Protection contre les flammes - Matériaux, assemblages de
matériaux et vêtements à propagation de flamme limitée (ISO 14116:2015)
Ta slovenski standard je istoveten z: EN ISO 14116:2015
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
13.340.10 Varovalna obleka Protective clothing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 14116
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2015
ICS 13.340.10 Supersedes EN ISO 14116:2008
English Version
Protective clothing - Protection against flame - Limited flame
spread materials, material assemblies and clothing (ISO
14116:2015)
Vêtements de protection - Protection contre les flammes - Schutzkleidung - Schutz gegen Flammen - Materialien,
Matériaux, assemblages de matériaux et vêtements à Materialkombinationen und Kleidung mit begrenzter
propagation de flamme limitée (ISO 14116:2015) Flammenausbreitung (ISO 14116:2015)
This European Standard was approved by CEN on 19 June 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14116:2015 E
worldwide for CEN national Members.

Contents Page
European foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 89/686/EEC .4

European foreword
This document (EN ISO 14116:2015) has been prepared by Technical Committee ISO/TC 94 "Personal safety
- Protective clothing and equipment" in collaboration with Technical Committee CEN/TC 162 “Protective
clothing including hand and arm protection and lifejackets” the secretariat of which is held by DIN
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2016, and conflicting national standards shall be withdrawn at
the latest by January 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
This document supersedes EN ISO 14116:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 14116:2015 has been approved by CEN as EN ISO 14116:2015 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 89/686/EEC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide one means of conforming to Essential Requirements of
the New Approach Directive 89/686/EEC on the approximation of the laws of the Member States relating to
personal protective equipment.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this International Standard given in Table ZA.1 confers, within the limits of the scope of this International
Standard, a presumption of conformity with the corresponding Essential Requirements of that Directive and
associated EFTA regulations.
Table ZA. — Correspondence between this International Standard and Directive 89/686/EEC
Clause(s)/sub- Qualifying remarks
clause(s) of this Essential Requirements (ERs) of Directive
European 89/686/EEC, Annex II
Standard
4.1, 4.4, 4.5,, , 6.3. 1.2.1 Absence of risks and other inherent nuisance
factors
4.5. 1.3.1 Adaptation of PPE to user morphology
8, 9 1.4 Information supplied by the manufacturer
5.3 2.4 PPE subject to ageing
6.2 1.3.2 Lightness and design strength
6.1. 3.6.1 PPE constituent materials and other components
8 2.12 PPE bearing identification marks related to health
and safety
WARNING: Other requirements and other EU Directives may be applicable to the products falling
within the scope of this standard.
INTERNATIONAL ISO
STANDARD 14116
Second edition
2015-07-01
Protective clothing — Protection
against flame — Limited flame spread
materials, material assemblies and
clothing
Vêtements de protection — Protection contre les flammes —
Matériaux, assemblages de matériaux et vêtements à propagation de
flamme limitée
Reference number
ISO 14116:2015(E)
©
ISO 2015
ISO 14116:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

ISO 14116:2015(E)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General and design requirements . 3
5 Sampling, pre-treatment, and ageing . 4
5.1 Sampling . 4
5.2 Pre-treatment of material . 4
5.3 Ageing . 4
5.4 Conditioning . 5
6 Performance requirements . 5
6.1 Limited flame spread performance . 5
6.2 Physical requirements . 6
6.2.1 Tensile Strength . 6
6.2.2 Tear strength . 6
6.2.3 Burst strength . 6
6.2.4 Seam strength . 6
6.3 Dimensional change of textile materials . 7
7 Classification . 7
7.1 Requirements for limited flame spread index 1 . 7
7.2 Requirements for limited flame spread index 2 . 7
7.3 Requirements for limited flame spread index 3 . 7
8 Marking . 8
8.1 Final index . 8
8.2 Single-layer materials . 8
8.3 Material assemblies . 8
8.4 Garments . 8
9 Information supplied by the manufacturer . 9
Annex A (normative) Uncertainty of measurement .10
Annex B (normative) Determination of property values for rating and classification .11
Bibliography .12
ISO 14116:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 94, Personal safety - Protective clothing and
equipment, Subcommittee SC 13, and by Technical Committee CEN/TC 162, Protective clothing including
hand and arm protection and lifejackets in collaboration.
This second edition cancels and replaces the first edition (ISO 14116:2008), which has been technically
revised to include the following changes:
— include test procedures for burst strength testing of woven materials;
— include new definition for determination of hole formation;
— modify clause in design requirements regarding garment overlaps;
— modify clause on sampling requirements;
— modify pre-treatment clause to include requirements for single use garments;
— modify clause for ageing due to washing (maximum number of cleaning procedures as indicated by
the manufacturer);
— include new requirement for measuring property value for rating and classification;
— modify test procedure for the flame testing of labels, badges, and retro-reflective materials;
— include requirement and procedure for testing of hardware;
— include requirement and test procedure for burst strength testing of knitted materials;
— include requirement and test procedure for tensile strength testing of non-woven materials;
— include requirement and test procedure for tear strength testing of non-woven materials;
— modify requirement for tear strength of woven and non-woven materials;
— modify flame spread definition;
iv © ISO 2015 – All rights reserved

ISO 14116:2015(E)
— modify requirement for flaming debris;
— modify afterflame requirement for flame spread of Index 3 materials;
— modify afterglow requirement for flame spread of Index 1, Index 2, and Index 3 materials.;
— include statement for flame spread testing in regard to interlining materials for Index 2 and Index 3
materials;
— include normative Annex for uncertainty of measurement;
— include normative Annex for measuring property value for rating and classification.
ISO 14116:2015(E)
Introduction
The purpose of this International Standard is to provide minimum performance requirements for
clothing in order to reduce the possibility of the clothing and/or its materials burning when in occasional
and brief contact with small flames and thereby, itself constituting a hazard.
For complete protection against exposure to flame, it will be necessary to protect the head, face, hands,
and/or feet with suitable PPE and, in some cases, appropriate respiratory protection might also be
considered necessary.
[5]
Attention is drawn to ISO/TR 2801:2007, which sets out guidelines for selection, use, care, and
maintenance of protective clothing against flame.
Nothing in this International Standard is intended to restrict any jurisdiction, purchaser, or manufacturer
from exceeding these minimum requirements.
vi © ISO 2015 – All rights reserved

INTERNATIONAL STANDARD ISO 14116:2015(E)
Protective clothing — Protection against flame — Limited
flame spread materials, material assemblies and clothing
1 Scope
This International Standard specifies the performance requirements for the limited flame spread
properties of all materials, all material assemblies, and protective clothing in order to reduce the
possibility of the clothing burning when in occasional and brief contact with small flames and thereby
constituting a hazard. Additional requirements for clothing are also specified, including design
requirements, mechanical requirements, marking, and information supplied by the manufacturer.
When protection against heat hazards is necessary, in addition to protection against flame, this
International Standard is not appropriate. International Standards such as ISO 11612 are to be used
instead.
A classification system is given for materials, material assemblies, and garments which are tested
according to ISO 15025, Procedure A.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 13934-1, Textiles — Tensile properties of fabrics — Part 1: Determination of maximum force and
elongation at maximum force using the strip method
ISO 13935-2, Textiles — Seam tensile properties of fabrics and made-up textile articles — Part 2:
Determination of maximum force to seam rupture using the grab method
ISO 13937-2, Textiles — Tear properties of fabrics — Part 2: Determination of tear force of trouser-shaped
test specimens (Single tear method)
ISO 13938-1, Textiles — Bursting properties of fabrics — Part 1: Hydraulic method for determination of
bursting strength and bursting distension
ISO 13938-2, Textiles — Bursting properties of fabrics — Part 2: Pneumatic method for determination of
bursting strength and bursting distension
ISO 15025, Protective clothing — Protection against heat and flame — Method of test for limited flame
spread
ISO 13688, Protective clothing — General requirements
ISO 9073-4, Textiles — Test methods for nonwovens — Part 4: Determination
...