prEN 16972

SLOVENSKI STANDARD
01-maj-2016
&HVWQDYR]LOD1RVLOQDYR]LOD]DL]PHQOMLYHNHVRQHUD]UHGD&L]PHQOMLYHFLVWHUQH
UD]UHGD&LQ
,62]DERMQLNH3ULNOMXþQHPHUH
Road vehicles - Carrying vehicles for swap bodies class C, swap tanks class C and 20'
ISO containers - Interface dimensions
Straßenfahrzeuge - Trägerfahrzeuge für Wechselbehälter Klasse C und 20' ISO-
Container - Anschlussmaße
Ta slovenski standard je istoveten z: prEN 16972
ICS:
43.080.10 Tovornjaki in priklopniki Trucks and trailers
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2016
ICS 43.080.10
English Version
Road vehicles - Carrying vehicles for swap bodies class C,
swap tanks class C and 20' ISO containers - Interface
dimensions
Straßenfahrzeuge - Trägerfahrzeuge für
Wechselbehälter Klasse C und 20' ISO-Container -
Anschlussmaße
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 119.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16972:2016 E
worldwide for CEN national Members.

Contents Page
European Foreword . 3
1 Scope . 4
2 Normative references . 4
3 General requirements . 4
4 Load bearing surfaces . 4
5 Front stop . 5
6 Twist lock systems . 5
Annex A (normative) Geometrical requirements for the twist lock system . 6
Figure A.1 — Twist lock system . 6
Annex B (normative) Connecting dimensions of the carrier vehicle. 7
Figure B.1 — Connection dimensions carrying vehicle . 7
Annex C (normative) Position of load bearing surfaces . 8
Figure C.1 — Setup of load transmission areas for trucks, center-axle trailers and hitched
trailers . 8
Figure C.2 — Setup of load transmission areas for trucks, center-axle trailers and hitched
trailers . 8
Figure C.3 — Setup of additional load transmission areas for 20' ISO-Containers, stackable
swap containers and swap tank containers . 9
Figure C.4 — Directing device assistance . 9
Bibliography . 10

European Foreword
This document (prEN 16972:2016) has been prepared by Technical Committee CEN/TC 119 “Swap
bodies”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
1 Scope
This European Standard sets the connection dimensions of carrier vehi
...