iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 16240:2013

(Main)

Light transmitting flat solid polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods

Light transmitting flat solid polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods

This European Standard specifies the requirements for light transmitting flat solid polycarbonate (PC) sheets for internal and external use in walls, roofs and ceilings.
This European Standard applies to light transmitting flat extruded solid PC sheets of minimum thickness 2 mm, without or with uniform functional layers (e.g. coating, co-extruded layer) made from PC-based or other materials.
It also specifies the test methods needed for the evaluation of conformity and marking of the sheets.

Lichtdurchlässige, flache Massivplatten aus Polycarbonat (PC) für Innen- und Außenanwendungen an Dächern, Wänden und Decken - Anforderungen und Prüfverfahren

Diese Europäische Norm legt die Anforderungen an lichtdurchlässige, flache Massivplatten aus Polycarbonat (PC) für Innen- und Außenanwendungen an Wänden, Dächern und Decken fest.
Diese Europäische Norm gilt für lichtdurchlässige, flache, extrudierte Massivplatten aus PC mit einer Mindestdicke von 2 mm, mit oder ohne gleichmäßigen Funktionsschichten (z. B. Beschichtung, koextrudierte Schicht) aus PC basierten oder sonstigen Materialien.
Außerdem legt sie die für die Evaluierung der Konformität und die Kennzeichnung der Platten erforderlichen Prüfverfahren fest.

Plaques d’éclairement pleines planes en polycarbonate (PC) pour usage intérieur ou extérieur dans les toitures, bardages et plafonds - Exigences et méthodes d’essai

La présente Norme européenne spécifie les exigences relatives aux plaques d'éclairement pleines planes en polycarbonate (PC) pour usage intérieur ou extérieur dans les toitures, bardages et plafonds.
La présente Norme européenne s'applique aux plaques d'éclairement pleines planes extrudées en PC d'une épaisseur minimale de 2 mm, avec ou sans couches fonctionnelles uniformes (par exemple, revêtement, couche co-extrudée) en matériaux à base de PC ou autres matières plastiques.
Elle spécifie également les méthodes d'essai nécessaires pour l'évaluation de la conformité ainsi que le marquage des plaques.

Prosojne, ploščate, masivne polikarbonatne (PC) plošče za notranje in zunanje strehe, stene in strope - Zahteve in preskusne metode

General Information

Status
Published
Publication Date
03-Dec-2013
Withdrawal Date
29-Jun-2014
ICS
83.140.10 - Films and sheets
91.060.10 - Walls. Partitions. Facades
Technical Committee
CEN/TC 128 - Roof covering products for discontinuous laying and products for wall cladding
Drafting Committee
CEN/TC 128/SC 9 - Prefabricated accessories for roofing
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
22-Jul-2022
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/121 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on internal and external wall and ceiling finishes
M/122 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on roof coverings, rooflights, roof windows and ancillary products
Ref Project
SIST EN 16240:2014 - Light transmitting flat solid polycarbonate (PC) sheets for internal and external roofs, walls and ceilings - Requirements and test methods

Buy Standard

EN 16240:2014EN 16240:2014
PreviousNext
Standard
EN 16240:2014
English language
45 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Lichtdurchlässige, flache, massive Platten aus Polycarbonat (PC) für Innen- und Außenanwendungen an Dächern, Wänden und Decken - Anforderungen und PrüfverfahrenPlaques d'éclairement pleines planes en polycarbonate (PC) pour toitures, bardages et plafonds intérieurs et extérieurs - Exigences et méthodes d'essaiLight transmitting flat solid polycarbonate (PC) sheets for internal and external roofs, walls and ceilings - Requirements and test methods91.060.20StreheRoofs91.060.10Stene. Predelne stene. FasadeWalls. Partitions. Facades83.140.10Filmi in folijeFilms and sheetsICS:Ta slovenski standard je istoveten z:EN 16240:2013SIST EN 16240:2014en,de01-februar-2014SIST EN 16240:2014SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16240
December 2013 ICS 83.140.10; 91.060.10 English Version
Light transmitting flat solid polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods
Plaques d'éclairement pleines planes en polycarbonate (PC) pour usage intérieur ou extérieur dans les toitures, bardages et plafonds - Exigences et méthodes d'essai
Lichtdurchlässige, flache Massivplatten aus Polycarbonat (PC) für Innen- und Außenanwendungen an Dächern, Wänden und Decken - Anforderungen und Prüfverfahren This European Standard was approved by CEN on 5 October 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16240:2013 ESIST EN 16240:2014

Foreword .4 Introduction .5 1 Scope .6 2 Normative references .6 3 Terms, definitions and symbols .7 3.1 Terms and definitions .7 3.2 Symbols .8 4 Requirements .9 4.1 Visual appearance .9 4.2 Dimensions and mass per unit area and their tolerances .9 4.3 Spectral characteristics . 10 4.4 Total solar energy transmittance . 10 4.5 Impact resistance. 11 4.6 Durability . 12 4.7 Deformation behaviour . 14 4.8 Airborne sound insulation . 14 4.9 Thermal transmittance . 14 4.10 Water vapour permeability . 16 4.11 Water/air tightness. 16 4.12 Linear thermal expansion . 16 4.13 Reaction to fire . 16 4.14 External fire performance . 16 4.15 Resistance to fire . 16 4.16 Net heat of combustion . 17 4.17 Presence of functional layers . 17 4.18 Release of dangerous substances . 17 4.19 Resistance to fixings . 17 4.20 Temporary protective coverings . 17 5 Test and calculation methods . 17 5.1 Dimensional tolerances and mass per unit area . 17 5.2 Artificial ageing . 20 5.3 Yellowness index . 21 5.4 Small hard body impact resistance . 21 5.5 Deformation behaviour . 22 5.6 Airborne sound insulation . 23 5.7 Reaction to fire . 23 6 Assessment and verification of constancy of performance – AVCP . 27 6.1 General . 27 6.2 Product type determination . 27 6.3 Factory production control (FPC) . 28 6.4 Initial inspection of factory and of FPC . 30 6.5 Continuous surveillance of FPC . 31 7 Marking and labelling . 31 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation . 33 SIST EN 16240:2014
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 2588:2024(Main)
Aerospace series - Bearing, spherical plain in corrosion resisting steel with assembly slots - Dimensions and loads
kSIST FprEN 2588:2024

This document specifies the characteristics of spherical plain bearings in corrosion resisting steel, with assembly slots, metric series, with or without lubrication holes and groove, intended for use in fixed or moving parts of aircraft structure and control mechanisms, within the temperature range from −54 °C to 150 °C.
It also applies to the following temperature ranges when lubricated with the following greases (see EN 2337):
-   ester type very high pressure grease (code letter A), operating range from −73 °C to 121 °C;
-   synthetic hydrocarbon type very high pressure grease general purpose (code letter B), operating range from −54 °C to 177 °C.
Their field of application when lubricated with grease code letter A is limited to 121 °C.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 18075:2024(Main)
Resilient, textile, laminate and modular mechanical locked floor coverings - Circular economy and sustainability - Recommendations/guidelines for design
kSIST-TS FprCEN/TS 18075:2024

The aim of this document is to provide general recommendations and guidelines on how to design a product to optimize its reuse and recyclability at the end of its lifetime as well as to take into account sustainable sourcing of materials for all floor covering product groups covered by CEN/TC 134. The overall target is to avoid waste and pollution and to achieve a product fit for the circular economy.
In a linear economy, the focus of product design is on developing new products without considering the recycling or reuse of the raw materials used.
This document provides guidance for processes allowing for (raw) materials used to be returned to the economic cycle based on circular design principles. The focus is on open systems that allow for economically interesting alternatives and are not limited to the principle of closed cycles (product to product).
Specific attention is given to renewable materials, where applicable.
The document is structured along the life cycle of the products, starting with the production phase.
Excluded is packaging, which is not considered part of the product end-of-life stage.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-3:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 3: Tests for emissions of volatile organic substances (ISO 18562-3:2024)
kSIST FprEN ISO 18562-3:2024

This document specifies tests for the emissions of volatile organic substances from the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The tests of this document are intended to quantify emissions of volatile organic substances that are added to the respirable gas stream by the materials of the gas pathway. This document establishes acceptance criteria for these tests.
NOTE            Gaseous emission of volatile organic substances includes emissions of volatile organic compounds, semi-volatile organic compounds and very volatile organic compounds.
This document addresses potential contamination of the gas stream arising from the gas pathways of medical devices or accessories, which is then conducted to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the surfaces of gas pathways that are in direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories containing gas pathways that are addressed by this document include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder or room air taken into the medical device is not addressed by ISO 18562 series.
This document is intended to be read in conjunction with ISO 18562-1.

  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 899-2:2024(Main)
Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2024)
kSIST FprEN ISO 899-2:2024

This document specifies a method for determining the flexural creep of plastics in the form of standard test specimens under specified conditions such as those of pre-treatment, temperature and humidity. It is only applicable to a simple freely supported beam loaded at mid-span (three-point-loading test).
 The method is suitable for use with rigid and semi-rigid non-reinforced, filled and fibre-reinforced plastics materials (see ISO 472 for definitions) test specimens moulded directly or machined from sheets or moulded articles.
NOTE            The method can be unsuitable for certain fibre-reinforced materials due to differences in fibre orientation
The method is intended to provide data for engineering-design, quality control, research and development purposes.
The method might not be applicable for determining the flexural creep of rigid cellular plastics (attention is drawn in this respect to ISO 1209-1 and ISO 1209-2).

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-2:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 2: Tests for emissions of particulate matter (ISO 18562-2:2024)
kSIST FprEN ISO 18562-2:2024

This document specifies tests for the emissions of particulate matter from the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The tests of this document are intended to quantify particles from 0,25 µm diameter to 10 µm diameter that are emitted by the medical device, its parts or accessories into the respirable gas stream. This document establishes acceptance criteria for these tests.
This document does not address nanoparticles. Insufficient data exist to establish exposure limits for particles less than 0,25 µm diameter.
This document does not address particles larger than 10 µm diameter. These particles are deposited in the nasal cavity. Additional information can be needed for medical devices or accessories that bypass the nose. This is outside the scope of this document but can be required by some authorities having jurisdiction.
This document therefore adopts the same approach as the US Environmental Protection Agency (EPA) in setting limits based solely on particle size and not their chemistry.
This document addresses potential contamination of the gas stream arising from the gas pathways, which is then conducted to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the particles that are deliberately released by a nebulizer (i.e. the therapeutic agent).
This document does not address biological evaluation of the surfaces of gas pathways that have direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories, containing gas pathways that are addressed by this document, include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces, and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder or room air taken into the medical device is not addressed by ISO 18562 (all parts).

  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13997:2024(Main)
Protective clothing - Mechanical properties - Determination of resistance to cutting by sharp objects (ISO 13997:2024)
oSIST prEN ISO 13997:2024

This document specifies a tomodynamometer cut test method and related calculations, for use on materials and assemblies designed for protective clothing, including gloves. The test determines resistance to cutting by sharp edges, such as knives, sheet metal parts, swarf, glass, bladed tools and castings.
When this document is cited as a test method in a material or product requirement standard, that standard contains the necessary information to permit the application of this document to the particular product.
This test does not provide data on the resistance to penetration by pointed objects such as needles and thorns, or the point of sharp-edged blades. The test described in this document is not considered suitable for testing materials made from chain mail and metal plates. The text of this document does not include provisions for the safeguard of the operator.

  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17984-1:2024(Main)
Assistance dogs - Part 1: Vocabulary
SIST EN 17984-1:2024

This document specifies the terms and definitions that apply to:
—   different types of assistance dogs;
—   the beneficiary and client services;
—   health and disabilities;
—   assistance dog service providers;
—   assistance dog training staff and related professionals;
—   the socialization and training processes;
—   conformity assessment, identification and registration;
—   accessibility.

  • Draft
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16709:2024(Main)
Automotive fuels - High FAME diesel fuel (B20 and B30) - Requirements and test methods
kSIST FprEN 16709:2024

This document specifies requirements and test methods for marketed and delivered high FAME (B20 and B30) diesel fuel for use in diesel engine vehicles designed or subsequently adapted to run on such fuel. High FAME diesel fuel is a mixture of up to 20 % (V/V) in total and up to 30 % (V/V) in total respectively fatty acid methyl esters (commonly known as FAME) complying with EN 14214 and automotive diesel fuel complying with EN 590.
For maintenance and control reasons high FAME (B20 and B30) diesel fuel is to be used in captive fleets that are intended to have an appropriate fuel management (see Clause 4).
NOTE 1   These products are allowed in Europe [4], but national legislation can set additional requirements or rules concerning, or even prohibiting, marketing or delivering of the product.
NOTE 2   For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction and the volume fraction.
NOTE 3   In this document, A-deviations apply (see Annex A).

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 683-7:2024(Main)
Heat-treatable steels, alloy steels and free-cutting steels - Part 7: Bright products of non-alloy and alloy steels (ISO 683-7:2023)
oSIST prEN ISO 683-7:2024

This document specifies the technical delivery requirements for bright steel products in the drawn, peeled/turned or additional ground condition and they are intended for mechanical purposes, for example for machine parts. The bright steel products are subdivided into the following steel types:
a)       non-alloy general engineering steels;
b)       non-alloy free-cutting steels;
c)        non-alloy and alloy case-hardening steels;
d)       non-alloy and alloy steels for quenching and tempering.
Bright products of stainless steels are not part of this document, they are covered by ISO 16143-4.

  • Draft
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12594:2024(Main)
Bitumens and bituminous binders - Preparation of test samples
kSIST FprEN 12594:2023

This document specifies methods for preparing test samples of bitumens and bituminous binders in order to test their properties.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day