FprEN 13121-3
(Main)GRP tanks and vessels for use above ground - Part 3: Design and workmanship
GRP tanks and vessels for use above ground - Part 3: Design and workmanship
This European Standard gives requirements for the design, fabrication, inspection, testing and verification of GRP tanks and vessels with or without thermoplastics lining for storage or processing of fluids, factory made or site built, non-pressurized or pressurized up to 10 bar, for use above ground. Further requirements are presented in normative Annex G.
The terms vessels and tanks as used in this part of EN 13121 include branches up to the point of connection to pipe work or other equipment by bolting and supports, brackets or other attachments bonded directly to the shell.
This part of EN 13121 covers vessels and tanks subject to temperatures between - 40 °C and 120 °C.
Excluded from this part of EN 13121 are:
- tanks and vessels for the transport of fluids;
- underground storage tanks;
- spherical vessels;
- vessels and tanks of irregular shape;
- tanks and vessels with double containment where the double wall is considered structural;
- tanks and vessels which are subject to the risk of explosion, or failure of which may cause an emission of radioactivity;
- specification for fibre reinforced cisterns of one piece and sectional construction for the storage, above ground, of cold water (see EN 13280).
Oberirdische GFK-Tanks und -Behälter - Teil 3: Auslegung und Herstellung
Dieses Dokument legt Anforderungen für Auslegung, Fertigung, Prüfung und den Nachweis für oberirdische GFK-Tanks und –Behälter, mit oder ohne thermoplastische(r) Auskleidung fest, die im Werk oder auf der Baustelle gefertigt und drucklos oder bis zu 10 bar druckbeaufschlagt sind und zur Lagerung oder Verarbeitung von Fluiden dienen. Weitere Anforderungen sind im normativen Anhang G dargelegt.
Die Begriffe Behälter und Tank im Sinne dieses Dokuments umfassen auch Stutzen(Abzweige) bis zur Verbindung zu Rohrleitungen oder anderen Anlagenteilen, wie Verschraubungen, Unterstützkonstruktionen, Halterungen oder anderen Anbauteilen, die unmittelbar mit der Schale verbunden sind.
Dieses Dokument gilt für Behälter und Tanks, die Temperaturen zwischen −40 °C und 120 °C ausgesetzt sind.
Dieser Teil der EN 13121 gilt nicht für
Tanks und Behälter für den Transport von Fluiden,
unterirdische Lagertanks,
kugelförmige Behälter,
Behälter und Tanks mit unregelmäßiger Form,
Tanks und Behälter in doppelwandiger Ausführung, bei denen die Doppelwandigkeit statisch berücksichtigt wird,
Tanks und Behälter, die bei Explosion oder Undichtheit die Emission radioaktiver Strahlungen zur Folge haben können, und
einteilige und mehrteilige oberirdische faserverstärkte Tanks für die Lagerung von Kaltwasser (siehe EN 13280).
Réservoirs et récipients en PRV pour applications hors sol - Partie 3 : Conception et fabrication
Nadzemni rezervoarji in posode iz umetnih mas, ojačanih s steklenimi vlakni - 3. del: Konstruiranje in izdelava
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2022
Nadzemni rezervoarji in posode iz umetnih mas, ojačanih s steklenimi vlakni - 3.
del: Konstruiranje in izdelava
GRP tanks and vessels for use above ground - Part 3: Design and workmanship
Oberirdische GFK-Tanks und -Behälter - Teil 3: Auslegung und Herstellung
Réservoirs et récipients en PRV pour applications hors sol - Partie 3 : Conception et
fabrication
Ta slovenski standard je istoveten z: prEN 13121-3
ICS:
23.020.10 Nepremične posode in Stationary containers and
rezervoarji tanks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
prEN 13121-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2022
ICS 23.020.10 Will supersede EN 13121-3:2016
English Version
GRP tanks and vessels for use above ground - Part 3:
Design and workmanship
Réservoirs et récipients en PRV pour applications hors Oberirdische GFK-Tanks und -Behälter - Teil 3:
sol - Partie 3 : Conception et fabrication Auslegung und Herstellung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 210.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13121-3:2022 E
worldwide for CEN national Members.
prEN 13121-3:2022 (E)
Contents
European foreword . 9
Introduction . 10
1 Scope . 11
2 Normative references . 11
3 Terms and definitions . 13
4 Symbols and abbreviations . 15
5 Information and requirements to be supplied and documented . 17
5.1 General . 17
5.2 Information to be obtained by the manufacturer . 17
5.3 Information to be prepared by the manufacturer . 18
5.4 Final documentation . 19
6 Material . 19
6.1 General . 19
6.2 Chemical protective barrier . 19
6.2.1 General . 19
6.2.2 Thermoplastics linings . 19
6.2.3 Resin based linings . 19
6.3 Flammability . 19
6.4 Electrical resistivity . 19
7 Mechanical properties . 20
7.1 General . 20
7.2 Heat deflection temperature. 20
7.3 Laminate construction . 20
7.4 Laminate thickness . 22
7.5 Laminate properties . 22
7.6 Inter-laminar shear strength . 22
7.6.1 Laminate . 22
7.6.2 Thermoplastics linings . 22
7.7 Peel strength of laminates . 23
7.8 Pull-off strength of laminates and thermoplastic liner . 23
7.9 Selection of physical properties of materials and allowable design factors . 23
7.9.1 General . 23
7.9.2 Basic design . 23
7.9.3 Advanced design . 24
7.9.4 Design factors . 25
7.9.5 Overall design factors K and F . 25
8 Determination of design strain and loadings . 28
8.1 General . 28
8.2 Limit design strains . 28
8.2.1 General . 28
8.2.2 Limit resin strain ε . 28
ar
8.2.3 Limit strain for laminate or lamina ε . 28
lim
8.2.4 Limit test strain ε . 29
test
8.3 Limit design laminate loadings . 29
8.4 Determination of the mechanical values from laminates . 29
8.4.1 General . 29
8.4.2 Calculation of laminate values without experimental test data . 30
8.4.3 Laminate with experimental data . 30
8.5 Laminate thickness . 30
prEN 13121-3:2022 (E)
9 Design . 31
9.1 Introduction . 31
9.2 Determination of external loads . 31
9.2.1 Snow loads . 31
9.2.2 Wind loads . 31
9.2.3 Seismic loads . 32
9.2.4 Insulation loads . 34
9.2.5 Loads resulting from connections . 34
9.2.6 Agitation . 34
9.2.7 Pressure due to inadequate venting . 34
9.2.8 Personnel loading . 34
9.2.9 Internal stresses in vessels and tanks due temperatures . 35
9.3 Verification by the partial factor method . 35
9.3.1 General . 35
9.3.2 Dimensioning by using (A ⋅γ )-factored loads. 40
F,i
9.4 Drawings and design calculations . 41
9.5 Design details . 41
9.5.1 Design temperature TS . 41
9.5.2 Pressure . 41
10 Design analysis . 42
10.1 Symbols and units .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.