EN ISO 4404-1:2012

SLOVENSKI STANDARD
01-september-2012
1DGRPHãþD
SIST EN ISO 4404-1:2006
1DIWDLQQDIWQLSURL]YRGL'RORþHYDQMHNRUR]LMVNHRGSRUQRVWLQHJRUOMLYLK
KLGUDYOLþQLKWHNRþLQGHO7HNRþLQHNLYVHEXMHMRYRGR,62
Petroleum and related products - Determination of the corrosion resistance of fire-
resistant hydraulic fluids - Part 1: Watercontaining fluids (ISO 4404-1:2012)
Mineralölerzeugnisse und verwandte Produkte - Bestimmung der
korrosionsverhindernden Eigenschaften von schwer entflammbaren Druckflüssigkeiten -
Teil 1: Wasser enthaltende Flüssigkeiten (ISO 4404-1:2012)
Pétrole et produits connexes - Détermination de la résistance à la corrosion de fluides
hydrauliques difficilement inflammables - Partie 1: Fluides contenant de l'eau (ISO 4404-
1:2012)
Ta slovenski standard je istoveten z: EN ISO 4404-1:2012
ICS:
75.120 +LGUDYOLþQLIOXLGL Hydraulic fluids
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 4404-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2012
ICS 75.120 Supersedes EN ISO 4404-1:2006
English Version
Petroleum and related products - Determination of the corrosion
resistance of fire-resistant hydraulic fluids - Part 1: Water-
containing fluids (ISO 4404-1:2012)
Pétrole et produits connexes - Détermination de la Mineralölerzeugnisse und verwandte Produkte -
résistance à la corrosion de fluides hydrauliques Bestimmung der korrosionsverhindernden Eigenschaften
difficilement inflammables - Partie 1: Fluides contenant de von schwer entflammbaren Druckflüssigkeiten - Teil 1:
l'eau (ISO 4404-1:2012) Wasser enthaltende Flüssigkeiten (ISO 4404-1:2012)
This European Standard was approved by CEN on 30 June 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4404-1:2012: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 4404-1:2012) has been prepared by Technical Committee ISO/TC 28 "Petroleum
products and lubricants" in collaboration Technical Committee CEN/TC 19 “Gaseous and liquid fuels,
lubricants and related products of petroleum, synthetic and biological origin” the secretariat of which is held by
NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2013, and conflicting national standards shall be withdrawn at
the latest by January 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4404-1:2006.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 4404-1:2012 has been approved by CEN as a EN ISO 4404-1:2012 without any modification.

INTERNATIONAL ISO
STANDARD 4404-1
Second edition
2012-07-01
Petroleum and related products —
Determination of the corrosion resistance
of fire-resistant hydraulic fluids —
Part 1:
Water-containing fluids
Pétrole et produits connexes — Détermination de la résistance
à la corrosion de fluides hydrauliques difficilement inflammables —
Partie 1: Fluides contenant de l’eau
Reference number
ISO 4404-1:2012(E)
©
ISO 2012
ISO 4404-1:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

ISO 4404-1:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Reagents and materials . 2
6 Apparatus . 2
7 Producing the test fluid from an HFA-type fluid concentrate. 6
8 Procedure . 6
8.1 Test preparation . 6
8.2 Test . 7
8.3 Assessment . 7
9 Expression of results . 9
10 Precision . 9
11 Test report . 9
Annex A (normative) Preparation of test waters .10
Annex B (informative) Specifications of alternative standard materials for test strips .12
Annex C (informative) Explanatory comments .13
Annex D (informative) Table for reporting of results.14
Bibliography .15
ISO 4404-1:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4404-1 was prepared by Technical Committee ISO/TC 28, Petroleum products and lubricants.
This second edition cancels and replaces the first edition (ISO 4404-1:2001), which has been technically revised.
ISO 4404 consists of the following parts, under the general title Petroleum and related products — Determination
of the corrosion resistance of fire-resistant hydraulic fluids:
— Part 1: Water-containing fluids
— Part 2: Non-aqueous fluids
iv © ISO 2012 – All rights reserved

ISO 4404-1:2012(E)
Introduction
Water-containing hydraulic fluids are used in systems where fire resistance is required due to operating
conditions. The corrosion resistance of such fluids has to be assessed in order to choose a suitable system
design and prepare maintenance instructions.
INTERNATIONAL STANDARD ISO 4404-1:2012(E)
Petroleum and related products — Determination of
the corrosion resistance of fire-resistant hydraulic fluids —
Part 1:
Water-containing fluids
WARNING — The use of this part of ISO 4404 may involve hazardous materials, operations and
equipment. This part of ISO 4404 does not purport to address all of the safety problems associated
with its use. It is the responsibility of the user of this part of ISO 4404 to establish appropriate safety
and health practices and determine the applicability of regulatory limitations prior to use.
1 Scope
This part of ISO 4404 specifies a test method to determine the influence on metals of fire-resistant fluids in
categories HFA, HFB and HFC, as classified in ISO 6743-4. It evaluates the corrosion protection provided by
these fluids towards metal components used in hydraulic systems and installations.
A similar technique for fluids in category HFD is described in ISO 4404-2.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 648: 2008, Laboratory glassware — Single-volume pipettes
ISO 3696: 1987, Water for analytical laboratory use — Specification and test methods
ISO 3819: 1985, Laboratory glassware — Beakers
ISO 5598: 2008, Fluid power systems and components — Vocabulary
ISO 6344-1: 1998, Coated abrasives — Grain size analysis — Part 1: Grain size distribution test
ISO 20783-1: 2011, Petroleum and related products — Determination of emulsion stability of fire-resistant
fluids — Part 1: Fluids in category HFAE
DIN 12331: 1988, Laboratory glassware; beakers
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5598:2008 apply.
ISO 4404-1:2012(E)
4 Principle
Test strips of appropriate metals, both singly and in pairs, are partially submerged in the test fluid at a specific
temperature and for a specific period. The change in mass of each test strip, its surface appearance and the
change in the appearance of the fluid during the test are determined.
NOTE 1 When assessing the corrosivity of HF
...