EN 1465:2009
(Main)Adhesives - Determination of tensile lap-shear strength of bonded assemblies
Adhesives - Determination of tensile lap-shear strength of bonded assemblies
This European Standard specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.
NOTE This test procedure is not applicable for calculations needed for bond design in structural joints.
Klebstoffe - Bestimmung der Zugscherfestigkeit von Überlappungsklebungen
Diese Europäische Norm legt ein Verfahren zur Bestimmung der Zugscherfestigkeit von Überlappungs¬klebungen fest, wenn sie an einer Normalprobe und unter festgelegten Vorbehandlungs- und Prüf¬bedingungen bestimmt wird.
ANMERKUNG Dieses Prüfverfahren ist nicht für Berechnungen geeignet, die für die Auslegung von Klebever¬bindungen bei strukturellen Verbindungen benötigt werden.
Adhésifs - Détermination de la résistance au cisaillement en traction d'assemblages collés à recouvrement simple
La présente Norme européenne spécifie une méthode de détermination de la résistance au cisaillement
d’assemblages collés par essai de traction d’une éprouvette normalisée et dans des conditions de préparation
et d’essai spécifiées.
NOTE 1 Cette méthode d’essai ne peut pas être appliquée pour déterminer les caractéristiques nécessaires aux
calculs et à la conception des joints d’assemblages structuraux.
NOTE 2 Ces méthodes d’essai pour la détermination de la résistance au cisaillement en traction d’assemblages collés
à recouvrement simple avec des adhésifs pour bois sont aussi spécifiées dans l’EN 205 et l’EN 302-1.
Lepila - Določanje strižne trdnosti prekritih spojev dveh togih lepljencev z nategom
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.QDWHJRPKlebstoffe - Bestimmung der Zugscherfestigkeit von ÜberlappungsklebungenAdhésifs - Détermination de la résistance au cisaillement en traction d'assemblages collés à recouvrement simpleAdhesives - Determination of tensile lap-shear strength of bonded assemblies83.180LepilaAdhesivesICS:Ta slovenski standard je istoveten z:EN 1465:2009SIST EN 1465:2009en,fr,de01-maj-2009SIST EN 1465:2009SLOVENSKI
STANDARDSIST EN 1465:19981DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1465February 2009ICS 83.180Supersedes EN 1465:1994
English VersionAdhesives - Determination of tensile lap-shear strength ofbonded assembliesAdhésifs - Détermination de la résistance au cisaillementen traction d'assemblages collés à recouvrement simpleKlebstoffe - Bestimmung der Zugscherfestigkeit vonÜberlappungsklebungenThis European Standard was approved by CEN on 27 December 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1465:2009: ESIST EN 1465:2009
1 Scope This European Standard specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing. NOTE 1 This test procedure is not applicable for calculations needed for bond design in structural joints. NOTE 2 This test Test methods for the determination of tensile lap-shear strength of bonded assemblies with wood adhesives are also specified in EN 205 and EN 302-1 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13887, Structural Adhesives - Guidelines for surface preparation of metals and plastics prior to adhesive bonding EN ISO 291, Plastics - Standard atmospheres for conditioning and testing (ISO 291:2005) EN ISO 527-1, Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:1993 including Corr 1:1994) EN ISO 10365, Adhesives - Designation of main failure patterns (ISO 10365:1992) 3 Principle Adhesive lap-shear bond strength is determined by stressing in shear of a single overlap joint
(see Fig
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.