EN 14118-2:2003
(Main)Reinforcement - Specifications for textile glass mats (chopped strand and continuous filament mats) - Part 2: Methods of test and general requirements
Reinforcement - Specifications for textile glass mats (chopped strand and continuous filament mats) - Part 2: Methods of test and general requirements
This part 2 of EN 14118 provides the list of test methods and general requirements for chopped strand and continuous filament mats covered by the part 1.
Verstärkungsprodukte - Spezifikation für Textilglasmatten (Glasseiden- und Endlosmatten) - Teil 2: Prüfverfahren und allgemeine Anforderungen
Renfort - Spécifications des mats de verre textile (mats à fils coupés et mats à fils continus) - Partie 2: Méthodes d'essai et exigences générales
Ojačitve – Specifikacije za steklene tkanine (iz sekanih in neskončnih vlaken) – 2. del: Preskusne metode in splošne zahteve
General Information
Relations
Overview - EN 14118-2:2003 (textile glass mats, methods of test and general requirements)
EN 14118-2:2003 is the CEN European Standard that lists test methods and general requirements for textile glass mats - specifically chopped strand mats (CSM) and continuous filament mats (CFM). It is Part 2 of the EN 14118 series and complements Part 1 (designation) and Part 3 (specific requirements). The standard defines which physical, visual and labelling criteria apply and references the established ISO/EN test methods used for verifying mat properties.
Key topics and technical requirements
- Scope and purpose: Identifies applicable test methods and general quality requirements for CSM and CFM covered by Part 1.
- Normative references: Incorporates key test standards such as EN ISO 2078, EN ISO 1889, ISO 2558, ISO 3616, ISO 3342, ISO 3374, ISO 5025 and EN ISO 3344. These references define how measurements are made and reported.
- Properties:
- Characteristic properties (informative): glass type, strand linear density, binder type, recommended matrix compatibility.
- Controlled properties (subject to planned QC): mass per unit area (g/m2), combustible-matter content (includes sizing and binder), tensile strength (for CSM), moisture content, roll width.
- Visual properties: uniform appearance, acceptable/non‑conforming visible defects (tears, holes, dirty marks, clumps, thin or poorly bonded areas, irregular edges).
- Test methods: Standardized procedures referenced for determination of mass per unit area, thickness, tensile breaking force, moisture, binder solubility in styrene, and other metrics.
- Labelling and traceability: Each roll/pallet must carry identifiers enabling traceability - manufacturer name, mat designation (commercial name, mass per unit area, roll width), net mass, production/traceability references and optionally nominal roll length.
- Packaging and storage:
- Packaging must protect during handling, storage and transport.
- Minimum shelf-life expectation: 12 months under recommended conditions.
- Recommended storage: 10 °C to 35 °C, relative humidity < 85%; avoid direct sunlight, heat and moisture. Keep product dry and re‑seal partially used packages.
Applications and users
This standard is relevant to organisations involved in:
- Manufacturers of glass fiber reinforcement mats (quality control and product specification)
- Composite fabricators and laminators selecting chopped strand or continuous filament mats
- Test laboratories performing compliance testing to EN/ISO methods
- Procurement/specification engineers and designers in sectors using glass-fibre reinforced plastics (automotive, marine, wind energy, construction)
EN 14118-2:2003 helps ensure consistent material performance, traceability and reliable testing of textile glass mats used as reinforcement in composite components.
Related standards
- EN 14118-1: (Designation of textile glass mats)
- EN 14118-3:2003 (Specific requirements)
- Referenced test standards: EN ISO 2078, EN ISO 1889, ISO 2558, ISO 3616, ISO 3342, ISO 3374, ISO 5025, EN ISO 3344.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Verstärkungsprodukte - Spezifikation für Textilglasmatten (Glasseiden- und Endlosmatten) - Teil 2: Prüfverfahren und allgemeine AnforderungenRenfort - Spécifications des mats de verre textile (mats a fils coupés et mats a fils continus) - Partie 2: Méthodes d'essai et exigences généralesReinforcement - Specifications for textile glass mats (chopped strand and continuous filament mats) - Part 2: Methods of test and general requirements59.100.10Materiali iz steklenih vlakenTextile glass materialsICS:Ta slovenski standard je istoveten z:EN 14118-2:2003SIST EN 14118-2:2003en01-julij-2003SIST EN 14118-2:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14118-2February 2003ICS 59.100.10English versionReinforcement - Specifications for textile glass mats (choppedstrand and continuous filament mats) - Part 2: Methods of testand general requirementsRenfort - Spécifications des mats de verre textile (mats àfils coupés et mats à fils continus) - Partie 2: Méthodesd'essai et exigences généralesVerstärkungsprodukte - Spezifikation für Textilglasmatten(Glasseiden- und Endlosmatten) - Teil 2: Prüfverfahren undallgemeine AnforderungenThis European Standard was approved by CEN on 28 November 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14118-2:2003 ESIST EN 14118-2:2003
...
Frequently Asked Questions
EN 14118-2:2003 is a standard published by the European Committee for Standardization (CEN). Its full title is "Reinforcement - Specifications for textile glass mats (chopped strand and continuous filament mats) - Part 2: Methods of test and general requirements". This standard covers: This part 2 of EN 14118 provides the list of test methods and general requirements for chopped strand and continuous filament mats covered by the part 1.
This part 2 of EN 14118 provides the list of test methods and general requirements for chopped strand and continuous filament mats covered by the part 1.
EN 14118-2:2003 is classified under the following ICS (International Classification for Standards) categories: 59.100.10 - Textile glass materials. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 14118-2:2003 has the following relationships with other standards: It is inter standard links to EN 14728:2019. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase EN 14118-2:2003 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...