EN 573-5:2007

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium und Aluminiumlegierungen - Chemische Zusammensetzung und Form von Halbzeug - Teil 5: Bezeichnung von genormten KneterzeugnissenAluminium et alliages d'aluminium - Composition chimique et forme des produits corroyés - Partie 5: Codification des produits corroyés normalisésAluminium and aluminium alloys - Chemical composition and form of wrought products - Part 5: Codification of standardized wrought products77.150.10Aluminijski izdelkiAluminium products77.040.30Kemijska analiza kovinChemical analysis of metalsICS:Ta slovenski standard je istoveten z:EN 573-5:2007SIST EN 573-5:2007en,fr,de01-december-2007SIST EN 573-5:2007SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 573-5September 2007ICS 77.040.30; 77.120.10 English VersionAluminium and aluminium alloys - Chemical composition andform of wrought products - Part 5: Codification of standardizedwrought productsAluminium et alliages d'aluminium - Composition chimiqueet forme des produits corroyés - Partie 5: Codification desproduits corroyés normalisésAluminium und Aluminiumlegierungen - ChemischeZusammensetzung und Form von Halbzeug - Teil 5:Bezeichnung von genormten KneterzeugnissenThis European Standard was approved by CEN on 13 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 573-5:2007: ESIST EN 573-5:2007

CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licences on standardised standard products under reasonable and not discriminatory conditions then this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 573-5:2007

Codification
Identification Block Description Block European Standard Number Block Individual Item Block Figure 1 — Structure of codification system SIST EN 573-5:2007

RL (instead of C)Length as fabricated (random length) NOTE For products of irregular cross-sections which are not covered by this table, the reference code of the drawing should be written instead of the designation, followed by a figure describing the fixed length in millimetres or the designation "RL" if random length is required. a If a length is specified, this shall be considered as fixed length.
Table 2 — Codification for dimension and form of rolled products Product description Dimension symbols Explanation Strip, foil
A × B Thickness × width Sheet, plate
A × B × C Thickness × width × length Circle, hot-rolled
A × B Thickness × circle diameter Circle, cold-rolled
A × B Thickness × circle diameter
4.4 Examples 4.4.1 General The codification will be explained
...