EN 13880-6:2019

SLOVENSKI STANDARD
01-julij-2019
Nadomešča:
SIST EN 13880-6:2004
Toplo nanosljive tesnilne mase za stike - 6. del: Metoda priprave preskušancev
Hot applied joint sealants - Part 6: Method for the preperation of samples for testing
Heiß verarbeitbare Fugenmassen - Teil 6: Prüfverfahren zur Vorbereitung von Proben für
die Prüfung
Produits de scellement de joints appliqués à chaud - Partie 6 : Méthode d'essai pour la
préparation des échantillons destinés à l'essai
Ta slovenski standard je istoveten z: EN 13880-6:2019
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
93.080.20 Materiali za gradnjo cest Road construction materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13880-6
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2019
EUROPÄISCHE NORM
ICS 93.080.20 Supersedes EN 13880-6:2004
English Version
Hot applied joint sealants - Part 6: Method for the
preparation of samples for testing
Produits de scellement de joints appliqués à chaud - Heiß verarbeitbare Fugenmassen - Teil 6:
Partie 6 : Méthode d'essai pour la préparation des Prüfverfahren zur Vorbereitung von Proben für die
échantillons destinés à l'essai Prüfung
This European Standard was approved by CEN on 25 February 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13880-6:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Apparatus . 6
6 Procedure. 6
6.1 Marking, labelling and packing . 6
6.2 Preparation of composite sample . 6
6.3 Pouring of the samples to be tested . 7
7 Test report . 7
Bibliography . 8

European foreword
This document (EN 13880-6:2019) has been prepared by Technical Committee CEN/TC 227 “Road
materials”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2019, and conflicting national standards shall
be withdrawn at the latest by October 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13880-6:2004
This European Standard is one of a series of standards as listed below:
— EN 13880-1, Hot applied joint sealants — Part 1: Test method for the determination of density at
25 °C
— EN 13880-2, Hot applied joint sealants — Part 2: Test method for the determination of cone
penetration at 25 °C
— EN 13880-3, Hot applied joint sealants — Part 3: Test method for the determination of penetration
and recovery (resilience)
— EN 13880-4, Hot applied joint sealants — Part 4: Test method for the determination of heat
resistance — Change in penetration value
— EN 13880-5, Hot applied joint sealants — Part 5: Test method for the determination of flow resistance
— EN 13880-6, Hot applied joint sealants — Part 6: Test method for the preparation of samples for
testing
— EN 13880-7, Hot applied joint sealants — Part 7: Function testing of joint sealants
— EN 13880-8, Hot applied joint sealants — Part 8: Test method for the determination of the change in
weight of fuel resistance joint sealants after fuel immersion
— EN 13880-9, Hot applied joint sealants — Part 9: Test method for the determination of compatibility
with asphalt pavements
— EN 13880-10, Hot applied joint sealants — Part 10: Test method for the determination of adhesion
and cohesion following continuous extension and compression
— EN 13880-11, Hot applied joint sealants — Part 11: Test method for the preparation of asphalt test
blocks used in the function test and for the determination of compatibility with asphalt pavements
— EN 13880-12, Hot applied joint sealants — Part 12: Test method for the manufacture of concrete test
blocks for testing (recipe methods)
— EN 13
...