EN 13880-2:2003
(Main)Hot applied joint sealants - Part 2: Test method for the determination of cone penetration at 25°C
Hot applied joint sealants - Part 2: Test method for the determination of cone penetration at 25°C
This European Standard describes a method for determining the cone penetration of hot applied joint sealants using a standard penetrometer fitted with a suitable penetration cone. The initial and fuel immersed penetration values are recorded using this test method as required in prEN 14188-1.
Heiß verarbeitbare Fugenmassen - Teil 2: Prüfverfahren zur Bestimmung der Konus-Penetration bei 25°C
Diese Europäische Norm beschreibt ein Verfahren zur Bestimmung der Konus-Penetration von heiß verarbeit-baren Fugenmassen unter Anwendung eines genormten Penetrometers, das mit einem geeigneten Penetra-tionskonus ausgerüstet ist. Mit dem nach prEN 14188-1 geforderten Prüfverfahren werden die Konus-Pene-trationswerte von heiß verarbeitbaren Fugenmassen im Anlieferungszustand und nach Lagerung in Treibstoff bestimmt.
Produits de scellement de joints appliqués à chaud - Partie 2: Méthode d'essai pour la détermination de la pénétration au cône à 25°C
Cette Norme européenne décrit une méthode de détermination de la pénétration au cône des produits de scellement de joints appliqués à chaud en utilisant un pénétromètre normalisé muni d'un cône de pénétration adapté. Les valeurs de pénétrabilité initiale et après immersion dans un hydrocarbure, sont obtenues à l'aide de la présente méthode d'essai, conformément aux exigences du prEN 14188-1.
Toplo nanosljive tesnilne mase za stike – 2. del: Preskusna metoda za ugotavljanje penetracije (s stožcem) pri 25 °C
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Toplo nanosljive tesnilne mase za stike – 2. del: Preskusna metoda za ugotavljanje penetracije (s stožcem) pri 25 °CHeiß verarbeitbare Fugenmassen - Teil 2: Prüfverfahren zur Bestimmung der Konus-Penetration bei 25°CProduits de scellement de joints appliqués a chaud - Partie 2: Méthode d'essai pour la détermination de la pénétration au cône a 25°CHot applied joint sealants - Part 2: Test method for the determination of cone penetration at 25°C93.080.20Materiali za gradnjo cestRoad construction materials91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 13880-2:2003SIST EN 13880-2:2004en01-junij-2004SIST EN 13880-2:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13880-2August 2003ICS 93.080.20English versionHot applied joint sealants - Part 2: Test method for thedetermination of cone penetration at 25°CProduits de scellement de joints appliqués à chaud - Partie2: Méthode d'essai pour la détermination de la pénétrationau cône à 25°CHeiß verarbeitbare Fugenmassen - Teil 2: Prüfverfahrenzur Bestimmung der Konus-Penetration bei 25°CThis European Standard was approved by CEN on 2 May 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13880-2:2003 ESIST EN 13880-2:2004
Determination of the penetration after fuel immersion.8A.1Principle.8A.2Apparatus.8A.3Preparation and conditioning of test specimens.8A.4Procedure.8SIST EN 13880-2:2004
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.