EN 10246-15:2000
(Main)Non-destructive testing of steel tubes - Part 15: Automatic ultrasonic testing of strip/plate used in the manufacture of welded steel tubes for the detection of laminar imperfections
Non-destructive testing of steel tubes - Part 15: Automatic ultrasonic testing of strip/plate used in the manufacture of welded steel tubes for the detection of laminar imperfections
This Part of EN 10246 specifies requirements for the ultrasonic testing of strip/plate used in the manufacture of welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. NOTE 1: In the case of welded tube, an alternative ultrasonic testing specification for the detection of laminar imperfections is available which may be applied at the manufacturer's option by ultrasonic testing of the tube subsequent to seam welding in accordance with EN 10246-14.
Zerstörungsfreie Prüfung von Stahlrohren - Teil 15: Automatische Ultraschallprüfung von Band/Blech, das für die Herstellung geschweißter Stahlrohre eingesetzt wird, zum Nachweis von Dopplungen
Dieser Teil der EN 10246 legt die Anforderungen an die automatische Ultraschallprüfung zum Nachweis von Dopplungen in Band bzw. Blech fest, das für die Herstellung geschweißter Rohre eingesetzt wird. Die Norm enthält Festlegungen über Zulässigkeitklassen und die Einstellung der Prüfanlagen. ANMERKUNG 1: Für geschweißte Rohre steht zum Nachweis von Dopplungen eine alternative Ultraschall-Prüfnorm zur Verfügung, die nach Wahl des Herstellers angewendet werdendarf, indem das Rohr nach dem Schweißen einer Ultraschallprüfung nach EN 10246-14 unterzogen wird.
Essais non destructifs des tubes en acier - Partie 15: Contrôle automatique par ultrasons pour la détection des dédoublures dans les bandes/plaques utilisées pour la fabrication des tubes en acier soudés
La présente partie de l'EN 10246 spécifie les prescriptions relatives au contrôle par ultrasons des bandes/plaques pour la détection des dédoublures utilisés pour la fabrication des tubes soudés. La norme spécifie des niveaux de sévérité et des procédures d'étalonnage. NOTE 1: Pour les tubes soudés une autre méthode de contrôle par ultrasons pour la détection des dédoublures, peut être appliquée, au gré du producteur, sur tube après soudage, conformément au prEN 10246-14.
Neporušitveno preskušanje jeklenih cevi - 15. del: Ugotavljanje laminarnih napak trakov/pločevine, ki se uporabljajo za izdelavo varjenih jeklenih cevi, z avtomatsko ultrazvočno preiskavo
General Information
- Status
- Withdrawn
- Publication Date
- 15-Feb-2000
- Withdrawal Date
- 31-Mar-2011
- Technical Committee
- ECISS/TC 110 - Steel tubes, and iron and steel fittings
- Drafting Committee
- ECISS/TC 29/SC 10 - Non-destructive testing
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 01-Apr-2011
- Completion Date
- 01-Apr-2011
Relations
- Effective Date
- 09-Apr-2011
Frequently Asked Questions
EN 10246-15:2000 is a standard published by the European Committee for Standardization (CEN). Its full title is "Non-destructive testing of steel tubes - Part 15: Automatic ultrasonic testing of strip/plate used in the manufacture of welded steel tubes for the detection of laminar imperfections". This standard covers: This Part of EN 10246 specifies requirements for the ultrasonic testing of strip/plate used in the manufacture of welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. NOTE 1: In the case of welded tube, an alternative ultrasonic testing specification for the detection of laminar imperfections is available which may be applied at the manufacturer's option by ultrasonic testing of the tube subsequent to seam welding in accordance with EN 10246-14.
This Part of EN 10246 specifies requirements for the ultrasonic testing of strip/plate used in the manufacture of welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. NOTE 1: In the case of welded tube, an alternative ultrasonic testing specification for the detection of laminar imperfections is available which may be applied at the manufacturer's option by ultrasonic testing of the tube subsequent to seam welding in accordance with EN 10246-14.
EN 10246-15:2000 is classified under the following ICS (International Classification for Standards) categories: 23.040.10 - Iron and steel pipes; 77.040.20 - Non-destructive testing of metals. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 10246-15:2000 has the following relationships with other standards: It is inter standard links to EN ISO 10893-9:2011. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 10246-15:2000 is associated with the following European legislation: EU Directives/Regulations: 97/23/EC; Standardization Mandates: M/005, M/071. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 10246-15:2000 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Zerstörungsfreie Prüfung von Stahlrohren - Teil 15: Automatische Ultraschallprüfung von Band/Blech, das für die Herstellung geschweißter Stahlrohre eingesetzt wird, zum Nachweis von DopplungenEssais non destructifs des tubes en acier - Partie 15: Contrôle automatique par ultrasons pour la détection des dédoublures dans les bandes/plaques utilisées pour la fabrication des tubes en acier soudésNon-destructive testing of steel tubes - Part 15: Automatic ultrasonic testing of strip/plate used in the manufacture of welded steel tubes for
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...