CEN ISO/TS 18234-11:2013

SLOVENSKI STANDARD
01-april-2013
Inteligentni transportni sistemi - Prometne in potovalne informacije (TTI) prek
izvedenske skupine za transportne protokole, binarni format 1. generacije (TPEG1)
- 11. del: Vsebnik lokacijskih referenc (TPEG-LRC) (ISO/TS 18234-11:2013)
Intelligent transport systems - Traffic and Travel Information (TTI) via transport protocol
experts group, generation 1 (TPEG1) binary data format - Part 11: Location Referencing
Container (TPEG1-LRC) (ISO/TS 18234-11:2013)
Intelligente Transportsysteme - Reise- und Verkehrsinformation (TTI) über Datenströme
der Transportprotokoll Expertengruppe, Generation 1 (TPEG1) binäres Datenformat -
Teil 11: Lokalisierungsreferenzcontainer (TPEG1-LRC) (ISO/TS 18234-11:2013)
Systèmes intelligents de transport - Informations sur le trafic et le tourisme via les
données de format binaire du groupe d'experts du protocole de transport, génération 1
(TPEG1) - Partie 11: Conteneur de référencement d'emplacement (ISO/TS 18234-
11:2013)
Ta slovenski standard je istoveten z: CEN ISO/TS 18234-11:2013
ICS:
03.220.01 Transport na splošno Transport in general
35.240.60 Uporabniške rešitve IT v IT applications in transport
transportu in trgovini and trade
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL SPECIFICATION
CEN ISO/TS 18234-11
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
February 2013
ICS 03.220.01; 35.240.60
English Version
Intelligent transport systems - Traffic and Travel Information
(TTI) via transport protocol experts group, generation 1 (TPEG1)
binary data format - Part 11: Location Referencing Container
(TPEG1-LRC) (ISO/TS 18234-11:2013)
Systèmes intelligents de transport - Informations sur le Intelligente Transportsysteme - Reise- und
trafic et le tourisme via les données de format binaire du Verkehrsinformation (TTI) über Datenströme der
groupe d'experts du protocole de transport, génération 1 Transportprotokoll Expertengruppe, Generation 1 (TPEG1)
(TPEG1) - Partie 11: Conteneur de référencement binäres Datenformat - Teil 11:
d'emplacement (ISO/TS 18234-11:2013) Lokalisierungsreferenzcontainer (TPEG1-LRC) (ISO/TS
18234-11:2013)
This Technical Specification (CEN/TS) was approved by CEN on 14 January 2013 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 18234-11:2013: E
worldwide for CEN national Members.

Contents Page
Foreword . 3
Foreword
This document (CEN ISO/TS 18234-11:2013) has been prepared by Technical Committee CEN/TC 278
“Road transport and traffic telematics", the secretariat of which is held by NEN, in collaboration with Technical
Committee ISO/TC 204 "Intelligent transport systems".
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
TECHNICAL ISO/TS
SPECIFICATION 18234-11
First edition
2013-02-01
Intelligent transport systems — Traffic
and Travel Information (TTI) via transport
protocol experts group, generation 1
(TPEG1) binary data format —
Part 11:
Location Referencing Container
(TPEG1-LRC)
Systèmes intelligents de transport — Informations sur le trafic et le
tourisme via les données de format binaire du groupe d'experts du
protocole de transport, génération 1 (TPEG1) —
Partie 11: Conteneur de référencement d'emplacement

Reference number
ISO/TS 18234-11:2013(E)
©
ISO 2013
ISO/TS 18234-11:2013(E)
©  ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO/TS 18234-11:2013(E)
Contents Page
Foreword . iv
Introduction . vi
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 2
3.1  dynamic location reference . 2
3.2  location referencing . 2
3.3  location referencing container . 2
3.4  message . 3
3.5  pre-coded location reference . 3
3.6  TPEG-LOC, TPEG Location . 3
4  Abbreviations . 3
5  Location Referencing Container . 4
5.1  TPEG-LRC Introduction . 4
5.2  TPEG-LRC Methods . 5
5.2.1  DLR1 Location . 5
5.2.2  Korean Node Link Location . 5
5.2.3  TMC Location . 5
5.2.4  TPEG Location . 6
5.2.5  VICS Link Location . 6
5.2.6  ETL Location . 6
5.2.7  GLR Location . 6
6  Message components . 6
6.1  List of Generic Component IDs . 6
6.2  LocationReferencingContainer . 7
6.3  TPEGLocationReference . 7
6.4  DLR1LocationReference . 8
6.5  TMCLocationReference . 8
6.6  KoreanNodeLinkLocationReference . 8
6.7  VICSLinkReference . 9
6.8  ETLLocationReference . 9
6.9  GLRLocationReference . 9
Annex A (normative) Binary SSF and Data Types . 10
Bibliography . 50

ISO/TS 18234-11:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of document:
— an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
— an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting
a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 18234-11 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 278, Road transport and traffic telematics, in collaboration with ISO Technical Committee TC 204,
Intelligent transport systems in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreem
...