iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14366:2004/FprA1

(Amendment)

Laboratory measurement of noise from waste water installations

Laboratory measurement of noise from waste water installations

This document:
-   specifies methods for the measurement of airborne and structure-borne sound produced in waste water and rain water installations under laboratory conditions;
-   defines the expression of the results.
It is applicable to waste water piping systems and parts thereof, but not to the actual sources of the wastewater, e.g. lavatories, toilets and bathtubs or any active units. It applies to pipes with natural ventilation and made of any common material in commonly used diameters (up to 150 mm).
The results obtained can be used for the comparison of products and materials. It may serve in estimating the behaviour of waste water systems in a building under certain conditions. Nevertheless, this standard does not provide a normalized procedure for calculating the acoustical properties of such installations in a building.
This revision will also consider the effect of an enclosure.

Messung der Geräusche von Abwasserinstallationen im Prüfstand

Der vorliegende europäische Norm-Entwurf
- legt Verfahren fest, mit denen in Abwasser- und Regenwasserinstallationen entstandener Luft- und Körper-schall unter Laborbedingungen gemessen werden kann;
- legt die Angabe der Ergebnisse fest.
Er ist auf Abwasser-Rohrleitungssysteme und deren Teile, jedoch nicht auf die eigentlichen Abwasserquellen, z. B. Waschräume, Toiletten und Badewannen, anwendbar. Er ist auf Rohre mit natürlicher Lüftung anwendbar, die aus jedem üblichen Material bestehen können und die üblichen Durchmesser haben.
Die erhaltenen Ergebnisse können für den Vergleich von Produkten und Werkstoffen verwendet werden. Er kann zur Einschätzung des Verhaltens von Abwassersystemen in einem Gebäude unter bestimmten Bedingungen dienen. Diese Norm liefert jedoch kein normiertes Verfahren zur Berechnung der akustischen Eigenschaften solcher Installationen in einem Gebäude.

Mesurage en laboratoire du bruit émis par les installations d'évacuation des eaux usées

Le présent projet de Norme européenne :
-   spécifie des méthodes permettant de mesurer le bruit aérien et le bruit structural générés par des installations d'évacuation des eaux usées et des eaux de pluie dans des conditions de laboratoire ;
-   définit l'expression des résultats.
Il s'applique aux systèmes de canalisations d'évacuation des eaux usées et aux éléments associés, à l'exclusion des véritables sources des eaux usées, par exemple les cuvettes de WC, les toilettes et les baignoires ou tout équipement actif. Il s'applique aux canalisations avec aération naturelle, réalisées en un matériau courant quelconque dans des diamètres couramment utilisés (jusqu'à 150 mm).
Les résultats obtenus peuvent être utilisés pour comparer les produits et les matériaux. Cela peut servir à apprécier le comportement des systèmes d'évacuation des eaux usées dans un bâtiment dans certaines conditions. Néanmoins, la présente norme ne fournit pas de mode opératoire normalisé pour le calcul des propriétés acoustiques de telles installations dans un bâtiment

Laboratorijsko merjenje hrupa pri napeljavah za odpadno vodo - Dopolnilo A1

General Information

Status
Not Published
ICS
17.140.20 - Noise emitted by machines and equipment
91.140.80 - Drainage systems
Technical Committee
CEN/TC 126 - Acoustic properties of building products and of buildings
Drafting Committee
CEN/TC 126/WG 7 - Laboratory measurement of noise from waste water installation
Current Stage
5060 - Closure of Vote - Formal Approval
Start Date
27-Jun-2019
Due Date
25-Jul-2020
Completion Date
27-Jun-2019
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
Mandate
M/BC/CEN/91/8 - CPD: Protection against noise
Ref Project
SIST EN 14366:2005/oprA1:2018 - Laboratory measurement of noise from waste water installations

Relations

Merged Into
EN 14366:2004+A1:2019 - Laboratory measurement of noise from waste water installations
Effective Date
18-Jan-2023
Amends
EN 14366:2004 - Laboratory measurement of noise from waste water installations
Effective Date
16-May-2018

Buy Standard

EN 14366:2005/oprA1:2018EN 14366:2005/oprA1:2018
PreviousNext
Draft
EN 14366:2005/oprA1:2018
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-november-2018
Laboratorijsko merjenje hrupa pri napeljavah za odpadno vodo - Dopolnilo A1
Laboratory measurement of noise from waste water installations
Messung der Geräusche von Abwasserinstallationen im Prüfstand
Mesurage en laboratoire du bruit émis par les installations d'évacuation des eaux usées
Ta slovenski standard je istoveten z: EN 14366:2004/prA1
ICS:
17.140.20 Emisija hrupa naprav in Noise emitted by machines
opreme and equipment
91.140.80 Drenažni sistemi Drainage systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
EN 14366:2004
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
September 2018
ICS 17.140.20; 91.140.80
English Version
Laboratory measurement of noise from waste water
installations
Mesurage en laboratoire du bruit émis par les Messung der Geräusche von Abwasserinstallationen im
installations d'évacuation des eaux usées Prüfstand
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 126.

This draft amendment A1, if approved, will modify the European Standard EN 14366:2004. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 14366-1:2023(Main)
Laboratory measurement of airborne and structure-borne sound from service equipment - Part 1: Application rules for waste water installations
SIST EN 14366-1:2023

This document characterizes waste water or rain water piping systems as airborne sound source and structure-borne sound source using the same method as the one described in EN 15657 for characterizing building service equipment. It therefore applies to equipment installed in any type of buildings (heavy or lightweight).
This document:
-   specifies laboratory measuring methods for determining the input data required for both comparing products and materials, and predicting sound levels in buildings using EN 12354 5. These input quantities are the piping system sound power level for airborne sound and three quantities for structure-borne sound (piping system free velocity, blocked force and mobility), from which the piping system installed power, source input for EN 12354 5, is determined;
-   specifies the method for the measurement of the equipment airborne sound power;
-   only considers piping systems connected to one supporting building element in a first step;
NOTE   Simultaneous structure-borne transmissions to wall and floor are more difficult to handle. In the configurations proposed in this document, the piping system is only connected to one supporting element and mechanically decoupled from the other elements.
-   includes configurations of vertical pipes with offset (deviated horizontally) connected to walls and horizontal pipes connected to ceilings, for which the measuring method is the same as the one defined for straight vertical pipes connected to walls. These complementary configurations are described in (normative) Annex A;
-   specifies laboratory test procedures for determining the performance of mitigation measures such as pipe enclosures (technical shaft) and pipe lining. The corresponding specifications are given in (normative) Annex B;
-   defines the expression of the results for use in comparing products and materials and for use as input data for prediction; however, the Single Number Quantities used to compare products cannot be used as a prediction or proof of compliance with requirements in a building;
-   indicates a method to transform the quantities measured according to EN 14366:2004+A1:2019, to the quantities used in this document; however, the calculated values cannot be used as certified values obtained by test, but only for comparison with new tests. This method is given in (informative) Annex C.
This document is applicable to waste water piping systems and parts thereof, but not to the actual sources of waste water, e.g. lavatories, toilets and bathtubs or any active units, which are considered separately in EN 12354 5 and are characterized separately. It applies to pipes with natural ventilation and made of any common material in commonly used diameters (up to 150 mm).

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14366-1:2023(Main)
Laboratory measurement of airborne and structure-borne sound from service equipment - Part 1: Application rules for waste water installations
SIST EN 14366-1:2023

This document characterizes waste water or rain water piping systems as airborne sound source and structure-borne sound source using the same method as the one described in EN 15657 for characterizing building service equipment. It therefore applies to equipment installed in any type of buildings (heavy or lightweight).
This document:
-   specifies laboratory measuring methods for determining the input data required for both comparing products and materials, and predicting sound levels in buildings using EN 12354 5. These input quantities are the piping system sound power level for airborne sound and three quantities for structure-borne sound (piping system free velocity, blocked force and mobility), from which the piping system installed power, source input for EN 12354 5, is determined;
-   specifies the method for the measurement of the equipment airborne sound power;
-   only considers piping systems connected to one supporting building element in a first step;
NOTE   Simultaneous structure-borne transmissions to wall and floor are more difficult to handle. In the configurations proposed in this document, the piping system is only connected to one supporting element and mechanically decoupled from the other elements.
-   includes configurations of vertical pipes with offset (deviated horizontally) connected to walls and horizontal pipes connected to ceilings, for which the measuring method is the same as the one defined for straight vertical pipes connected to walls. These complementary configurations are described in (normative) Annex A;
-   specifies laboratory test procedures for determining the performance of mitigation measures such as pipe enclosures (technical shaft) and pipe lining. The corresponding specifications are given in (normative) Annex B;
-   defines the expression of the results for use in comparing products and materials and for use as input data for prediction; however, the Single Number Quantities used to compare products cannot be used as a prediction or proof of compliance with requirements in a building;
-   indicates a method to transform the quantities measured according to EN 14366:2004+A1:2019, to the quantities used in this document; however, the calculated values cannot be used as certified values obtained by test, but only for comparison with new tests. This method is given in (informative) Annex C.
This document is applicable to waste water piping systems and parts thereof, but not to the actual sources of waste water, e.g. lavatories, toilets and bathtubs or any active units, which are considered separately in EN 12354 5 and are characterized separately. It applies to pipes with natural ventilation and made of any common material in commonly used diameters (up to 150 mm).

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 2588:2024(Main)
Aerospace series - Bearing, spherical plain in corrosion resisting steel with assembly slots - Dimensions and loads
kSIST FprEN 2588:2024

This document specifies the characteristics of spherical plain bearings in corrosion resisting steel, with assembly slots, metric series, with or without lubrication holes and groove, intended for use in fixed or moving parts of aircraft structure and control mechanisms, within the temperature range from −54 °C to 150 °C.
It also applies to the following temperature ranges when lubricated with the following greases (see EN 2337):
-   ester type very high pressure grease (code letter A), operating range from −73 °C to 121 °C;
-   synthetic hydrocarbon type very high pressure grease general purpose (code letter B), operating range from −54 °C to 177 °C.
Their field of application when lubricated with grease code letter A is limited to 121 °C.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 18075:2024(Main)
Resilient, textile, laminate and modular mechanical locked floor coverings - Circular economy and sustainability - Recommendations/guidelines for design
kSIST-TS FprCEN/TS 18075:2024

The aim of this document is to provide general recommendations and guidelines on how to design a product to optimize its reuse and recyclability at the end of its lifetime as well as to take into account sustainable sourcing of materials for all floor covering product groups covered by CEN/TC 134. The overall target is to avoid waste and pollution and to achieve a product fit for the circular economy.
In a linear economy, the focus of product design is on developing new products without considering the recycling or reuse of the raw materials used.
This document provides guidance for processes allowing for (raw) materials used to be returned to the economic cycle based on circular design principles. The focus is on open systems that allow for economically interesting alternatives and are not limited to the principle of closed cycles (product to product).
Specific attention is given to renewable materials, where applicable.
The document is structured along the life cycle of the products, starting with the production phase.
Excluded is packaging, which is not considered part of the product end-of-life stage.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-3:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 3: Tests for emissions of volatile organic substances (ISO 18562-3:2024)
kSIST FprEN ISO 18562-3:2024

This document specifies tests for the emissions of volatile organic substances from the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The tests of this document are intended to quantify emissions of volatile organic substances that are added to the respirable gas stream by the materials of the gas pathway. This document establishes acceptance criteria for these tests.
NOTE            Gaseous emission of volatile organic substances includes emissions of volatile organic compounds, semi-volatile organic compounds and very volatile organic compounds.
This document addresses potential contamination of the gas stream arising from the gas pathways of medical devices or accessories, which is then conducted to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the surfaces of gas pathways that are in direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories containing gas pathways that are addressed by this document include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder or room air taken into the medical device is not addressed by ISO 18562 series.
This document is intended to be read in conjunction with ISO 18562-1.

  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 899-2:2024(Main)
Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2024)
kSIST FprEN ISO 899-2:2024

This document specifies a method for determining the flexural creep of plastics in the form of standard test specimens under specified conditions such as those of pre-treatment, temperature and humidity. It is only applicable to a simple freely supported beam loaded at mid-span (three-point-loading test).
 The method is suitable for use with rigid and semi-rigid non-reinforced, filled and fibre-reinforced plastics materials (see ISO 472 for definitions) test specimens moulded directly or machined from sheets or moulded articles.
NOTE            The method can be unsuitable for certain fibre-reinforced materials due to differences in fibre orientation
The method is intended to provide data for engineering-design, quality control, research and development purposes.
The method might not be applicable for determining the flexural creep of rigid cellular plastics (attention is drawn in this respect to ISO 1209-1 and ISO 1209-2).

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-2:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 2: Tests for emissions of particulate matter (ISO 18562-2:2024)
kSIST FprEN ISO 18562-2:2024

This document specifies tests for the emissions of particulate matter from the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The tests of this document are intended to quantify particles from 0,25 µm diameter to 10 µm diameter that are emitted by the medical device, its parts or accessories into the respirable gas stream. This document establishes acceptance criteria for these tests.
This document does not address nanoparticles. Insufficient data exist to establish exposure limits for particles less than 0,25 µm diameter.
This document does not address particles larger than 10 µm diameter. These particles are deposited in the nasal cavity. Additional information can be needed for medical devices or accessories that bypass the nose. This is outside the scope of this document but can be required by some authorities having jurisdiction.
This document therefore adopts the same approach as the US Environmental Protection Agency (EPA) in setting limits based solely on particle size and not their chemistry.
This document addresses potential contamination of the gas stream arising from the gas pathways, which is then conducted to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the particles that are deliberately released by a nebulizer (i.e. the therapeutic agent).
This document does not address biological evaluation of the surfaces of gas pathways that have direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories, containing gas pathways that are addressed by this document, include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces, and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder or room air taken into the medical device is not addressed by ISO 18562 (all parts).

  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13997:2024(Main)
Protective clothing - Mechanical properties - Determination of resistance to cutting by sharp objects (ISO 13997:2024)
oSIST prEN ISO 13997:2024

This document specifies a tomodynamometer cut test method and related calculations, for use on materials and assemblies designed for protective clothing, including gloves. The test determines resistance to cutting by sharp edges, such as knives, sheet metal parts, swarf, glass, bladed tools and castings.
When this document is cited as a test method in a material or product requirement standard, that standard contains the necessary information to permit the application of this document to the particular product.
This test does not provide data on the resistance to penetration by pointed objects such as needles and thorns, or the point of sharp-edged blades. The test described in this document is not considered suitable for testing materials made from chain mail and metal plates. The text of this document does not include provisions for the safeguard of the operator.

  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17984-1:2024(Main)
Assistance dogs - Part 1: Vocabulary
SIST EN 17984-1:2024

This document specifies the terms and definitions that apply to:
—   different types of assistance dogs;
—   the beneficiary and client services;
—   health and disabilities;
—   assistance dog service providers;
—   assistance dog training staff and related professionals;
—   the socialization and training processes;
—   conformity assessment, identification and registration;
—   accessibility.

  • Draft
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16709:2024(Main)
Automotive fuels - High FAME diesel fuel (B20 and B30) - Requirements and test methods
kSIST FprEN 16709:2024

This document specifies requirements and test methods for marketed and delivered high FAME (B20 and B30) diesel fuel for use in diesel engine vehicles designed or subsequently adapted to run on such fuel. High FAME diesel fuel is a mixture of up to 20 % (V/V) in total and up to 30 % (V/V) in total respectively fatty acid methyl esters (commonly known as FAME) complying with EN 14214 and automotive diesel fuel complying with EN 590.
For maintenance and control reasons high FAME (B20 and B30) diesel fuel is to be used in captive fleets that are intended to have an appropriate fuel management (see Clause 4).
NOTE 1   These products are allowed in Europe [4], but national legislation can set additional requirements or rules concerning, or even prohibiting, marketing or delivering of the product.
NOTE 2   For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction and the volume fraction.
NOTE 3   In this document, A-deviations apply (see Annex A).

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day