EN 10108:2004
(Main)Round steel rod for cold heading and cold extrusion - Dimensions and tolerances
Round steel rod for cold heading and cold extrusion - Dimensions and tolerances
This European Standard specifies the dimensions, the tolerances, the nominal cross-sections and the nominal masses of the round rod used for cold heading and cold extrusion.
This European Standard concerns the round rod in non alloy and alloy steel grades specified in European Standard EN 10263 parts 1 to 5.
Runder Walzdraht aus Kaltstauch- und Kaltfließpressstählen - Maße und Grenzabmaße
Dieses Dokument legt die Maße, Grenzabmaße, Nennquerschnitte und Nennmassen für runden Walzdraht zum Kaltstauchen und Kaltfließpressen fest.
Dieses Dokument gilt für runden Walzdraht aus den unlegierten und legierten Stahlsorten nach den Europäischen Normen EN 10263-1 bis EN 10263-5.
Fil machine rond en acier pour déformation à froid et extrusion à froid - Dimensions et tolérances
La présente Norme européenne spécifie les dimensions, les tolérances, les sections nominales et les masses
nominales des fils machine ronds utilisés pour les articles de boulonnerie formés à froid.
La présente Norme européenne concerne les fils machine ronds en nuances d�acier non allié et allié
spécifiées dans les EN 10263 Parties 1 à 5.
Okrogle jeklene palice za hladno nakrčevanje in hladno iztiskovanje – Mere in tolerance
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.WROHUDQFHRunder Walzdraht aus Kaltstauch- und Kaltfließpressstählen - Maße und GrenzabmaßeFil machine rond en acier pour déformation a froid et extrusion a froid - Dimensions et tolérancesRound steel rod for cold heading and cold extrusion - Dimensions and tolerances77.140.65Jeklene žice, jeklene vrvi in verigeSteel wire, wire ropes and link chainsICS:Ta slovenski standard je istoveten z:EN 10108:2004SIST EN 10108:2004en01-december-2004SIST EN 10108:2004SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10108
October 2004 ICS 77.140.65 Supersedes EURONORM 108:1972English version
Round steel rod for cold heading and cold extrusion - Dimensions and tolerances
Fil machine rond en acier pour déformation à froid et extrusion à froid - Dimensions et tolérances
Runder Walzdraht aus Kaltstauch-und kaltfließpressstählen - Maße und Grenzabmaße This European Standard was approved by CEN on 9 July 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10108:2004: ESIST EN 10108:2004
page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Information to be supplied by the purchaser.4 5 Requirements.5 6 Nominal sections and nominal masses.5 7 Dimensions and Tolerances.6 8 Mass of coils and checks on dimensional tolerances.10 9 Claims.10
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.