ASTM D3302-02ae1

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
e1
Designation:D3302–02a
Standard Test Method for
1
Total Moisture in Coal
This standard is issued under the fixed designation D 3302; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1
e NOTE—Precision and Bias section was editorially revised and editorial changes were made throughout in July 2004.
1. Scope 2. Referenced Documents
2
1.1 This test method covers the measurement of the total 2.1 ASTM Standards:
moisture in coal as it exists at the site, at the time, and under D 121 Terminology of Coal and Coke
the conditions it is sampled. It is applicable to coals as mined, D 2013 Practice for Preparing Coal Samples for Analysis
processed, shipped, or used in normal commercial pursuits. It D 2234 Practice for Collection of a Gross Sample of Coal
is not applicable to coal-water slurries, sludges, or pulverized D 2961 Test Method for Single-Stage Total Moisture Less
products under 0.5-mm-diameter sieve size. It is applicable to than 15% in Coal Reduced to 2.36-mm (No. 8 Sieve)
coals of all ranks within the recognized limitations imposed by Topsize
oxidation and decomposition characteristics of lower rank D 3173 Test Method for Moisture in theAnalysis Sample of
coals. Because of its empirical nature, strict adherence to basic Coal and Coke
principles and permissive procedures are required for valid D 5865 Test Method for Gross Calorific Value of Coal and
results (seeAppendix X1). This complete standard is available Coke
to producers, sellers, and consumers as a total moisture method
3. Terminology
when other procedures or modifications are not mutually
3.1 Definitions—For additional definitions of terms used in
agreed on.
1.2 Since coal can vary from extremely wet (water- this test method, refer to Terminology D 121.
3.2 Definitions of Terms Specific to This Standard:
saturated) to completely dry, special emphasis must be placed
on the sampling, sample preparation, and the moisture deter- 3.2.1 air drying—a process of partial drying of a coal
sample to bring it to near equilibrium with the atmosphere in
mination itself to ensure total reliability of measurement.
Therefore, this standard entails collection of the gross sample, theroominwhichfurtherreduction/divisionofthesampleisto
take place.
sample preparation, and the method of determination.
3.2.2 air-dry loss—the loss in weight, expressed as a
1.3 While it is recognized that such a standard may be
unwieldy for routine usage in commercial operations, it can percent, resulting from each air-drying operation.
3.2.3 easily oxidized coals—low-rank coals such as subbi-
provide a common base for agreement in cases of dispute or
arbitration. The complete standard is referred to as the referee tuminous or lignitic coals.
3.2.4 equilibrium—conditionreachedinairdryingwhenthe
method. Embodied in the standard is the commercial method
starting with the crushed and divided sample when the gross change in weight of the sample, under conditions of ambient
temperature and humidity, is no more than 0.1 %/h or 0.05 %/
sample is not too wet to crush and divide. See Test Methods
1
D 2961 and D 3173 for other moisture methods. ⁄2 h.
3.2.5 residual moisture—that moisture remaining in the
1.4 The values stated in SI units are to be regarded as the
standard. The values given in parentheses are for information sample after air drying.
3.2.6 total moisture—see Terminology D 121.
only.
1.5 This standard does not purport to address all of the
4. Summary of Test Method (See Fig. 1)
safety concerns, if any, associated with its use. It is the
4.1 This test method is based on the loss in weight of a coal
responsibility of the user of this standard to establish appro-
sampleinanairatmosphereunderrigidlycontrolledconditions
priate safety and health practices and determine the applica-
of temperature, time, and airflow.
bility of regulatory limitations prior to use.
1
This test method is under the jurisdiction of ASTM Committee D05 on Coal
2
and Coke and is the direct responsibility of Subcommittee D05.21 on Methods of For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Analysis. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved April 10, 2002. Published July 2002. Originally Standards volume information, refer to the standard’s Document Summary page on
e1
published as D3302–74. Last previous edition D3302–00a . the ASTM website.
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959, United States.
1

---------------------- Page: 1 ----------------------
e1
D3302–02a
FIG. 1 Tot
...