ISO/TC 5/SC 1 - Steel tubes
Tubes en acier
General Information
ISO 10799-1:2011 specifies the technical delivery requirements for cold-formed welded structural hollow sections of circular, square or rectangular form. It is applicable to structural hollow sections formed cold without subsequent heat treatment. ISO 10799-1:2011 gives the grades, chemical composition and mechanical properties for non-alloy steels and fine grain steels.
- Standard26 pagesEnglish languagesale 15% off
ISO 10799-2:2011 specifies the tolerances for cold-formed welded circular, square and rectangular structural hollow sections, and gives the dimensions and sectional properties for a range of standard sizes.
- Standard28 pagesEnglish languagesale 15% off
ISO 12633-1:2011 specifies the technical delivery requirements for hot-finished hollow sections of circular, square or rectangular form. It is applicable to hollow sections formed hot with or without subsequent heat treatment or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot-formed product. Fine grain steels are generally delivered in the normalized condition. ISO 12633-1:2011 gives the grades, chemical composition and mechanical properties for non-alloy steels and fine grain steels.
- Standard24 pagesEnglish languagesale 15% off
ISO 12633-2:2011 specifies the tolerances for hot-finished circular, square and rectangular structural hollow sections, and gives the dimensions and sectional properties for a range of standard sizes.
- Standard27 pagesEnglish languagesale 15% off
The outside diameters and thicknesses of the tubes have been selected from ISO 4200. If thicknesses greater than 14,2 mm are needed, they should be choosen from ISO 4200. Specifies the diameters, tolerances and other parameters of tubes. It tabulates conventional masses for austenitic (table 1) and for ferritic and martensitic (table 2) stainless steel tubes.
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
Specifies the dimensions, tolerances, surface roughness, materials and hygienic requirements for seamless or welded tubes in straight length for the food industry.
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
Gives values of both plain end tubes for general purpose use and precision tubes. Its purpose is to give guidance on the selection of sizes for all activities concerned with the standardization of steel tubes, both nationally and internationally, to serve as a ready reckoner and to avoid the use by different countries of different masses for a tube of the same size. It is not applicable to tubes primarily intended to be screwed. This fourth edition cancels and replaces the third edition (1985), tables 2 and 3 of which have been technically revised by the addition of the outside diameter of 12.7 mm to series 2.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
Specifies the majority of tolerances on dimensions used by ISO/TC 5/SC 1 in drawing up International Standards concerning steel tubes. Is intended for use as a basic document by all ISO technical committees concerned with the standardization of steel tubes. It cannot, therefore, be used as a standard for the definiton of a product. This second edition cancels and replaces the first edition (1977), the standardized tolerances on thickness of which have been technically revised.
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
This part defines the most common symbols with the aim of standardizing and facilitating the use of terminology in standards for steel hollow sections and associated products. Five figures illustrate the meaning of the text. Annex A contains the bibliography.
- Standard4 pagesEnglish languagesale 15% off
- Standard6 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard4 pagesFrench languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
This first edition cancels and replaces ISO 3545:1981. This part defines the most common symbols with the aim of standardizing and facilitating the use of terminology in standards for steel tubes and associated products. Six figures illustrate the meaning of the text.
- Standard3 pagesEnglish languagesale 15% off
- Standard5 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard3 pagesFrench languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
This part defines the most common symbols with the aim of standardizing and facilitating the use of terminology in standards for steel hollow sections and associated products. Five figures illustrate the meaning of the text.
- Standard2 pagesEnglish languagesale 15% off
- Standard4 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard2 pagesFrench languagesale 15% off
- Standard2 pagesFrench languagesale 15% off
This second edition cancels and replaces the first edition (1975). Specifies the technical conditions for tubes. Tabulates the chemical composition (table 2) and mechanical properties (tables 3 and 5) as well as dimensions (table 8) ranging from 6 mm up to and including 160 mm (outside diameter) and tests (tables 6 and 7). For use in hydraulic piping equiment they shall be used only in annealed or normalized condition.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
This second edition cancels and replaces the first edition. Specifies the technical conditions for tubes. Tabulates the chemical composition (table 2) and mechanical properties (tables 3 to 6) as well as dimension (table 9) ranging from 4 mm up to and including 160 mm (outside diameter) and tests (tables 7 and 8). For use in hydraulic piping equipment they shall be used only in annealed or normalized condition.
- Standard7 pagesEnglish languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
- Standard7 pagesFrench languagesale 15% off
This second edition cancals and replaces the first edition (1973). Establishes the dimensions and charakteristics of seamless and welded steel tubes for separate series as follows: heavy series, medium series, ligth series 1. ligth series 2. Tabulates dimensions for DN 6 up to and including DN 150 as well as tolerances on the outside diameter.
- Standard3 pagesEnglish languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
- Standard3 pagesFrench languagesale 15% off
- Standard25 pagesEnglish languagesale 15% off
- Standard25 pagesFrench languagesale 15% off
- Standard24 pagesEnglish languagesale 15% off
- Standard25 pagesFrench languagesale 15% off
- Standard29 pagesEnglish languagesale 15% off
- Standard29 pagesFrench languagesale 15% off
- Standard24 pagesEnglish languagesale 15% off
- Standard25 pagesFrench languagesale 15% off
Specifies the dimensions, tolerances, surface roughness, materials, assembling and hygienic requirements for liners and gaskets. The clamps are not standardized but suitable clearances are specified in annex A. Male parts and liners are intended to be used with stainless steel tubes specified in ISO 2037.
- Standard12 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
Specifies the dimensions, tolerances, surface roughness, materials and hygienic requirements. The bends and tees are intended to be used with stainless steel tubes specified in ISO 2037.
- Standard6 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
Specifies the dimensions, tolerances, surface roughness, materials, assembling and hygienic requirements for male parts, liners, nuts and gaskets. Male parts and liners are intended to be used with stainless steel tubes specified in ISO 2037.
- Standard23 pagesEnglish languagesale 15% off
- Standard23 pagesFrench languagesale 15% off
- Standard23 pagesFrench languagesale 15% off
This second edition cancels and replaces the first edition (ISO 559:1977). Specifies the technical conditions for delivery of seamless and welded steel tubes for the conveyance of water and sewage at temperatures between - 10 °C and 120 °C. Does not apply to steel tubes in accordance with ISO 65 and similar plain end tubes. Contains references, definitions, informations to be supplied by the purchaser, and data relating to manufacturing process, chemical composition, mechanical properties and weldability, dimensions, masses and tolerances, appearance and soundness, inspection and testing, marking, lining or coating and documents.
- Standard14 pagesEnglish languagesale 15% off
- Standard14 pagesFrench languagesale 15% off
- Standard14 pagesFrench languagesale 15% off
- Standard5 pagesEnglish languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
- Standard5 pagesFrench languagesale 15% off
Specifies the dimensions and characteristics of seamless and welded austenitic steel tubes with dimensions corresponding to the medium series of ISO 65. Tabulates nominal sizes from DN 6 up to and including DN 150. The informative annex A contains the bibliography.
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
This second edition cancels and replaces the first edition (1975). Specifies the technical conditions for tubes. Tabulates the chemical composition (table 2) and mechanical properties (tables 3 to 6) as well as dimensions (table 9) ranging from 4 mm up to and including 260 mm (outside diameter) and tests (tables 7 and 8). For use in hydraulic piping equipment they shall be used only in the annealed or normalized condition.
- Standard8 pagesFrench languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
Specifies the coatings suitable for protecting surfaces of steel pipes and fittings, either individually or after assembly, and also the conditions for the application of such protective coatings. Applies to welded and seamless pipes of non-alloy steels used for the conveyance of fluids. The coatings of pipes intended for the transport of potable water and food products shall satisfy the public hygiene criteria of the country of use.
- Standard54 pagesEnglish languagesale 15% off
- Standard54 pagesFrench languagesale 15% off
- Standard54 pagesFrench languagesale 15% off
- Standard9 pagesEnglish languagesale 15% off
- Standard9 pagesFrench languagesale 15% off
- Standard3 pagesEnglish languagesale 15% off
Specifies the parameters of the metric series as follow: circular hollow sections (table3); square hollow sections (table 4); rectangular hollow sections (table 5). For square and rectangular sections, the sectional properties are calculated using the corner radius as given in table 1. Table 2 includes tolerances.
- Standard11 pagesEnglish languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
- Standard11 pagesFrench languagesale 15% off
Specifies the most usual preparation for welding, gives symbols, tabulates thicknesses together with designation, symbols, forms of ends (illustrated by figures), and dimension (degrees and root face width).
- Standard1 pageEnglish languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard1 pageFrench languagesale 15% off
- Standard3 pagesEnglish languagesale 15% off
This second edition cancels and replaces the first edition (1977). Specifies the diameters, thicknesses, tolerances and masses per unit length of fired tubes, including superheater and heat exchanger tubes. It does not apply für tubes according to ISO 6758 and ISO 6759. Tabulates carbon and alloy steel tubes (table 1), austenitic stainless steel tubes (table 2, ferritic and martensitic steel tubes (table 3)).
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
- Standard3 pagesEnglish languagesale 15% off
- Standard21 pagesEnglish languagesale 15% off
- Standard10 pagesEnglish languagesale 15% off
Specifies the characteristics of thick-walled seamless steel bars intended for the manufacture of tubular and annular machined parts.Gives designation for the order, tabulates chemical composition and mechanical properties as well as nominal dimensions ranging from 32 mm up to and including 250 mm (outside diameter).
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
Specifies the chracteristics of hot-finished tubes intended for use with or without subsequent machining operations. Cowers outside diameters from 33,7 mm up to and including 406,4 mm with thicknesses from 3,2 mm up to and including 65 mm. Lays down chemical compositon as well as mechnical and technical properties of material.
- Standard4 pagesEnglish languagesale 15% off
- Standard4 pagesFrench languagesale 15% off
- Standard4 pagesFrench languagesale 15% off