IEC/SC 34C - IEC_SC_34C
To prepare International Standards regarding specifications for lamp* controlgear and control devices. * The term lamp includes LED for General Lighting Services
IEC_SC_34C
To prepare International Standards regarding specifications for lamp* controlgear and control devices. * The term lamp includes LED for General Lighting Services
General Information
IEC 61347-2-2:2024 specifies safety requirements for electronic step-down convertors for use on DC supplies of up to 1 500 V or AC supplies of up to 1 000 V at 50 Hz or 60 Hz, and with a rated output voltage ≤ 50 V (RMS) at a frequency deviating from the supply frequency, or 120 V ripple free DC between conductors and between any conductor and earth, associated with tungsten-halogen lamps as specified in IEC 60357, and other filament lamps. This third edition cancels and replaces the second edition published in 2011. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) alignment with respect to the fourth edition of IEC 61347-1; - introduction of dated references to the fourth edition of IEC 61347-1 as appropriate; - deletion of the clauses and subclauses which are either no longer relevant or now covered in IEC 61347-1; b) scope extension to 1 500 V for direct current; c) scope clarification; d) deletion of unused definitions; e) revision of information and marking requirements; f) revision of compliance conditions for the measurement of the output voltage during fault condition testing and during thermal testing.
- Draft11 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61347-2-13:2024 specifies safety requirements for electronic controlgear for LED light sources for use on DC supplies up to 1 500 V or on AC supplies up to 1 000 V at 50 Hz or 60 Hz. This document is applicable for electronic controlgear for LED light sources with an output voltage (RMS) not higher than 1 000 V. This third edition cancels and replaces the second edition published in 2014 and Amendment 1:2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) alignment with respect to the fourth edition of IEC 61347-1: - introduction of dated references to the fourth edition of IEC 61347-1 as appropriate; - deletion of the clauses and subclauses which are either no longer relevant or now covered in IEC 61347-1; b) update of normative references, introducing dated references where appropriate; c) scope extension to 1 500 V for direct current; d) scope clarification; e) deletion of unused definitions; f) revision of information and marking requirements; g) new marking requirement "electronic controlgear for LED light sources"; h) new requirements for electronic controlgear for LED light sources with constant light output function or programmable current (additions to Clause 3, Clause 6, Clause 16 and Clause 18); i) modification of requirements for the determination of the output working voltage (new Clause 17); j) new requirements for the determination of the rated output characteristics (Clause 18).
- Draft16 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61347-1:2024 specifies general safety requirements for controlgear for electric light sources for use on DC supplies up to 1 500 V or AC supplies up to 1 000 V at 50 Hz or 60 Hz. This fourth edition cancels and replaces the third edition published in 2015 and Amendment 1:2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) complete review of document structure, including but not limited to what is individually described under items b) to s); b) removal of requirements for electromagnetic controlgear; c) addition of more specific requirements for control circuit insulation and corresponding marking; d) merging of thermal test requirements for transformers into a new Clause 16; e) clarification of specifications for the moisture resistance test; f) update of the normative reference to standards of the transformer series IEC 61558; g) correction of the normative reference for PCB testing with respect to flames and fire; h) update of further normative references where appropriate; i) allowance of an alternative DC electric strength test; j) addition of specific provisions for the use of bridging capacitors; k) update of fire hazard testing requirements; l) introduction of requirements for PELV applications; m) clearance distances now generally based on peak instead of RMS voltage values; n) introduction of a new type of protected emergency lighting controlgear; o) review and clarification of touch current and voltage requirements; p) clarification of the test sequence for independent controlgear with respect to the application of the IEC 60598 series versus the IEC 61347 series; q) introduction of reduced touch voltages and currents for interrupted DC voltage applications or pulse width modulation (PWM); r) changes concerning the recommendations for electric strength routine testing; s) merging of requirements for safety isolating controlgear from former Annex L into the main body of the document; t) introduction of Annex N intended to address touch current measurement; u) introduction of Annex O intended to provide information on document reorganization.
- Draft104 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61347-2-11:2024 specifies safety requirements for miscellaneous electronic circuits used with luminaires for use on DC supplies up to 1 500 V or on AC supplies up to 1 000 V at 50 Hz or 60 Hz. This second edition cancels and replaces the first edition published in 2001 and Amendment 1: 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) alignment with respect to the fourth edition of IEC 61347-1: - introduction of dated references to the fourth edition of IEC 61347-1 as appropriate; - deletion of clauses and subclauses which are either no longer relevant or now covered in IEC 61347-1; b) scope extension to 1 500 V for direct current; c) scope clarification; d) revision of information and marking requirements; e) addition of requirements for the determination of the output working voltage (new Clause 17).
- Draft11 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61347-2-1:2024 is available as IEC 61347-2-1:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61347-2-1:2024 specifies safety requirements for starting devices (starters other than glow starters and ignitors) for fluorescent and other discharge lamps for use on AC supplies up to 1 000 V at 50 Hz or 60 Hz which produce starting pulses not greater than 100 kV and which are used in combination with lamps and controlgear covered in IEC 60081, IEC 60188, IEC 60192, IEC 60662, IEC 60901, IEC 61167, IEC 61195, IEC 61199, IEC 61347-2-8 and IEC 61347-2-9. This second edition cancels and replaces the first edition published in 2000, Amendment 1:2005 and Amendment 2:2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) update of normative references, introducing dated references where appropriate; b) clarification of sample item numbers; c) alignment of clause numbers with those of IEC 61347-1; d) renumbering of Clause 15 and Clause 16.
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day
No scope available
- Amendment20 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62386-104:2019 The IEC 62386 series specifies a bus system for control by digital signals of electronic lighting equipment. This part of IEC 62386 applies to a system with wireless or alternative wired communication between its units, instead of a wired bus system, where the meaning of “wireless or alternative wired communication”, or in short “telecommunication”, is any type of communication network different from the wired system described in IEC 62386-101. Where the electronic lighting equipment is covered by the scope of IEC 61347 (all parts), it is in line with the requirements of IEC 61347 (all parts), with the addition of DC supplies.
- Standard54 pagesEnglish languagesale 10% offe-Library read for1 day
NEXT Action: CCMC to make available
2019-01-21 PeC: "Compliant" for LVD, sent to BT for integration (approved=D162/C043)
2018-11-21 PeC: sent to BT to keep ratification pending in order to fix harmonization (approved=D161/C073)
2018-11-12 PeC: submitted for HAS assessment
2017-07-31 - Cannot allocate for publication due to negative assessment from Consultant.
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
NEXT Action: CCMC to make available
2019-03-06 - Sent to BT for approval of A nnex ZA/ZZ (approved=D162/C075)
2018-12-13 PeC: "Compliant" for LVD
2018-11-20 PeC: sent to BT to keep ratification pending in order to fix harmonization (approved D161/C072)
2018-11-12 PeC: submitted for HAS assessment
2017-11-21 - Negative assessment is received during CDV stage. Consultant assessment request is missing for FDIS.
- Amendment17 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62442-2:2022 is available as IEC 62442-2:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62442-2:2022 defines a measurement method of the power losses of electromagnetic controlgear, the total input power and the standby power of electronic controlgear for discharge lamps (excluding low-pressure mercury fluorescent lamps). A calculation method of the efficiency of controlgear for discharge lamp(s) is also defined. It is assumed that the controlgear are designed for use on DC supplies up to 1 000 V and/or AC supplies up to 1 000 V at 50 Hz or 60 Hz. This third edition cancels and replaces the second edition published in 2018. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - the title of Part 2 has been modified; - this edition has been harmonized with IEC 62442-1 and IEC 62442-3; - the reference to and use of the measurement methods for non-active power consumption in accordance with IEC 63103 have been added.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62442-3:2022 is available as IEC 62442-3:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62442-3:2022 defines measurement and calculation methods for specifying the efficiency and the standby power of controlgear for tungsten-halogen lamps and LED light sources. This third edition cancels and replaces the second edition published in 2018. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - this edition has been harmonized with IEC 62442-1 and IEC 62442-2; - the reference to and use of the measurement methods for non-active power consumption in accordance with IEC 63103 have been added.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62442-1:2022 is available as IEC 62442-1:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62442-1:2022 defines a measurement and calculation method of the total input power for controlgear-lamp circuits when operating with their associated fluorescent lamp(s). The calculation method for the efficiency of the lamp controlgear is also defined. This document applies to electrical controlgear-lamp circuits consisting only of the controlgear and the lamp(s). It is intended for use on DC supplies up to 1 000 V and/or AC supplies up to 1 000 V at 50 Hz or 60 Hz. This third edition cancels and replaces the second edition published in 2018. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - this edition has been harmonized with IEC 62442-2 and IEC 62442-3; - the reference to and use of the measurement methods for non-active power consumption in accordance with IEC 63103 have been added.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62386-220:2019 specifies a bus system for control by digital signals of electronic lighting equipment which is in line with the requirements of IEC 61347 (all parts), with the addition of DC supplies. This document is applicable to control gear supporting centrally supplied emergency operation as described in EN 50171. This document does not apply to self-contained emergency lighting control gear. These types of control gear are specified in IEC 62386-202.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
NEW!IEC 62442-1:2018 is available as IEC 62442-1:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62442-1:2018 defines a measurement and calculation method of the total input power for controlgear-lamp circuits when operating with their associated fluorescent lamp(s). The calculation method for the efficiency of the lamp controlgear is also defined. This document applies to electrical controlgear-lamp circuits consisting only of the controlgear and the lamp(s). It is intended for use on DC supplies up to 1 000 V and/or AC supplies up to 1 000 V at 50 Hz or 60 Hz. This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision and has been harmonized with IEC 62442-2 and IEC 624423.
- Standard23 pagesEnglish languagesale 10% offe-Library read for1 day
NEW!IEC 62442-2:2018 is available as IEC 62442-2:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62442-2:2018 defines a measurement method of the power losses of electromagnetic controlgear, the total input power and the standby power of electronic controlgear for high intensity discharged lamps (excluding fluorescent lamps). A calculation method of the efficiency of controlgear for high intensity discharged lamp(s) is also defined. It is assumed that the controlgear are designed for use on DC supplies up to 1 000 V and/or AC supplies up to 1 000 V at 50 Hz or 60 Hz. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision and has been harmonized with IEC 62442-1 and IEC 62442-3.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
NEW!IEC 62442-3:2018 is available as IEC 62442-3:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62442-3:2018 defines a measurement method for the power losses of electromagnetic transformers as well as the power losses and the standby power of electronic convertors for tungsten-halogen lamps and for LED light source(s). It is applicable for controlgear that are designed for use on DC supplies up to 1 000 V and/or AC supplies up to 1 000 V at 50 Hz or 60 Hz. A calculation method of the efficiency of the mentioned controlgear for tungstenhalogen lamps and LED light source(s) is also defined. This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision and has been harmonized with IEC 62442-1 and IEC 624422.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61347-2-14:2018 specifies particular safety requirements for electronic controlgear for use on AC supplies up to 1 000 V at 50 Hz or 60 Hz and/or DC supplies with operating frequencies deviating from the supply frequency, associated with fluorescent induction lamps as specified in IEC 62532 and IEC 62639, for high-frequency operation.
- Standard39 pagesEnglish languagesale 10% offe-Library read for1 day
2020-08-05 NEXT ACTION: CCMC action by 2020-08-31
2020-08-03 CCMC to prepare request for BT
2020-08-03 since no 2nd assessment allowed, EC confirmed that TC met requirements for pos. ass.
2019-02-20 PC: "lack of compliance" for LVD, TC to adress comments
2019-01-30 PC: Sent for LVD assessment
2018-03-22 - missing Annex ZZ - on hold
2017-10-05 - Cannot allocate for publication due to missing assessment from Consultant.
- Amendment15 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62384:2020 is available as IEC 62384:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62384:2020 specifies performance requirements for electronic controlgear for use on DC or AC supplies up to 1 000 V (alternating current at 50 Hz or 60 Hz) and with an output frequency which can deviate from the supply frequency, associated with LED modules according to IEC 62031. Controlgear for LED modules specified in this document are designed to provide constant voltage or current. Deviations from the pure voltage and current types do not exclude the gear from this document. This second edition cancels and replaces the first edition published in 2006 and Amendment 1:2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - scope extension (direct current from 250 V to 1 000 V); - new specifications for measuring the power factor for controlgear with settable/non-constant output (for instance, to allow for constant light output); - deletion of audio frequency requirements; - selection of current test circuit by module capacitance (instead of selecting by having or not having logic circuitry) plus test circuit setup changes.
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 61347 specifies particular safety requirements for electronic controlgear for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz and at an output frequency which can deviate from the supply frequency, associated with LED modules.
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
This international Standard specifies performance requirements for electronic control gear for use on a.c. at 50 Hz or 60 Hz and/or d.c. supplies, both up to 1 000 V, with operating frequencies deviating from the supply frequency, associated with fluorescent lamps as specified in IEC 60081 and IEC 60901, and other fluorescent lamps for high-frequency operation.
NOTE 1 Tests in this standard are type tests. Requirements for testing individual control gear during production are not included.
NOTE 2 There are regional standards regarding the regulation of mains current harmonics and immunity for endproducts like luminaires and independent control gear. In a luminaire, the control gear is dominant in this respect. Control gear, together with other components, should comply with these standards.
- Amendment34 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard states the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including 2,5 kVAr, and not less than 0,1 µF, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m.
- Amendment8 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62733:2015 provides general and safety requirements for programmable components used in products covered by IEC 61347. The requirements of this standard are only applicable to the programmable components (including its embedded software) in the electronic lamp controlgear. For other electric/electronic circuits and their components in the electronic lamp controlgear, the requirements of IEC 61347 series apply.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62811:2015 specifies performance requirements for electronic controlgear for use on a.c. and/or d.c. supplies up to 1 000 V and/or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with discharge lamps, as specified in IEC 61167, which have information for low frequency square wave operation, where the frequency range of the low frequency is from 70 Hz to 400 Hz.
- Standard36 pagesEnglish languagesale 10% offe-Library read for1 day
NEW! IEC 61347-1:2015 is available as IEC Standards+ 61347-1:2015 which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 61347-1:2015 specifies general and safety requirements for lamp controlgear for use on d.c. supplies up to 250 V and/or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz. This third edition cancels and replaces the second edition published in 2007, Amendment 1:2010 and Amendment 2:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) additional marking requirements; b) additional requirements for creepage distances and clearances: - for working voltages with operating frequencies up to 30 kHz; - for working voltages with higher operating frequencies than 30 kHz; - for impulse and resonance voltages ignition; - for basic, supplementary and reinforced insulation; - for insulation between circuits; - for coated or potted controlgear; c) modification of definition of ELV and FELV; d) modification of schematic drawing, showing the different controlgear classification and insulation requirements; e) scope extension; f) new Annex A: test to establish whether a conductive part is a live part which may cause an electric shock; g) new Annex M: creepage distances and clearances for controlgear where a higher degree of availability (impulse withstand category III) may be requested; h) new Annex Q: example for Up calculation; i) new Annex P: creepage distances and clearances and distance through isolation (DTI) for lamp controlgear which are protected against pollution by the use of coating or potting; j) new Annex R: concept of creepage distances and clearances.
- Standard124 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61347-2-13:2014 specifies particular safety requirements for electronic controlgear for use on d.c. or a.c. supplies up to 1 000 V (a.c. at 50 Hz or 60 Hz) and at an output frequency which can deviate from the supply frequency, associated with LED modules. Controlgear for LED modules specified in this standard are designed to provide constant voltage or current at SELV or higher voltages. Deviations from the pure voltage and current types do not exclude the gear from this standard. This second edition cancels and replaces the first edition published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition. a) Replacement of the SELV-equivalent requirements by SELV requirements and reference to the SELV requirements of Annex L in IEC 61347-1:2007/AMD2:2012. b) Reference to IEC 61347-1 for the protection against accidental contact with live parts, moisture resistance and insulation and electric strength. c) New Annex J for emergency lighting requirements.
- Standard28 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61347-2-3:2011 specifies particular safety requirements for electronic control gear for use on a.c. and d.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with fluorescent lamps as specified in IEC 60081 and IEC 60901, and other fluorescent lamps for high-frequency operation. This second edition cancels and replaces the first edition published in 2000, its Amendment 1 (2004) and its Amendment 2 (2006), IEC 61347-2-4 published in 2000, IEC 61347-2-5 published in 2000 and IEC 61347-2-6 published in 2000. This second edition constitutes a technical revision. The significant revisions with respect to the first edition are: - rectifying test conditions when dimming; - construction requirements; - measurement circuits and limits for HF leakage currents; - modification of the structure to become a standard exclusively for a.c. and d.c. central supplied electronic control gear for general lighting and Annex J cover centrally- supplied emergency control gear. This publication is to be read in conjunction with IEC 61347-1:2007. The contents of the corrigendum of September 2011 have been included in this copy.
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
2013-10-11 - Publication editing allocated to odessy@cencenelec.eu
- Amendment9 pagesEnglish languagesale 10% offe-Library read for1 day
34C/977/RVC established on 2011-05-20: To be published without FDIS stage*20130930: Publication allocated to odessy@cencenelec.eu
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61347-2-9:2012 series specifies particular safety requirements for electromagnetic controlgear for discharge lamps such as high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium vapour and metal halide lamps. The standard covers inductive-type electromagnetic controlgear for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with discharge lamps, having rated wattages, dimensions and characteristics as specified in IEC 60188, IEC 60192 and IEC 60662. This second edition cancels and replaces the first edition published in 2000, Amendment 1:2003 and Amendment 2:2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) the addition of a new Clause 14; b) the word 'ballast' is changed to 'electromagnetic controlgear'. This publication is to be read in conjunction with IEC 61347-1:2007.
- Standard34 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61347-2-7:2011 specifies particular safety requirements for battery supplied electronic controlgear for maintained and non-maintained emergency lighting purposes. It includes specific requirements for electronic controlgear and control units for self-contained luminaires for emergency lighting as specified by IEC 60598-2-22. This third edition cancels and replaces the second edition published in 2006. It constitutes a technical revision. Significant changes introduced into this third edition include: - modification of IEC 61347-2-7 to become a standard exclusively for d.c. battery supplied electronic controlgear for emergency lighting (self-contained) IEC 61347-2-3 Annex J is intended to cover centrally supplied emergency controlgear; - update of Clause 22 - Recharging devices; - modification of Clause 20 battery voltage characterisation to support EBLF measurement. This to simplify and increase reproducibility of testing; - rationalisation of requirements between IEC 61347-2-7 and IEC 60598-2-22 requirements of IEC 60598-2-22 being transferred to IEC 61347-2-7. This publication is to be read in conjunction with IEC 61347-1:2007.
- Standard39 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61347-2-2:2011 specifies particular safety requirements for electronic step-down convertors for use on d.c. supplies of up to 250 V or a.c. supplies of up to 1 000 V, at 50 Hz or 60 Hz and with rated output voltage 50 V r.m.s. at a frequency deviating from the supply frequency, or 120 V ripple free d.c. between conductors and between any conductor and earth, associated with tungsten-halogen lamps as specified in IEC 60357 and other filament lamps. This second edition of IEC 61347-2-2 replaces the first edition (2000), Amendment 1 (2005) and Amendment 2 (2006). The major modification for this second edition is the changeover from SELV equivalent to SELV. This publication is to be read in conjunction with IEC 61347-1:2007.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62386-209:2011 specifies a protocol and test procedures for the control by digital signals of electronic control gear that can change their light colour. This publication contains .pdf files, which reproduce the test sequences illustrated in Figures 5 to 127. These files are intended to be used as a complement and do not form an integral part of the publication. This publication is to be read in conjunction with IEC 62386-101:2009 and IEC 62386-102:2009.
- Standard204 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 61347-2-3:2011 specifies particular safety requirements for electronic control gear for use on a.c. and d.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with fluorescent lamps as specified in IEC 60081 and IEC 60901, and other fluorescent lamps for high-frequency operation. This second edition cancels and replaces the first edition published in 2000, its Amendment 1 (2004) and its Amendment 2 (2006), IEC 61347-2-4 published in 2000, IEC 61347-2-5 published in 2000 and IEC 61347-2-6 published in 2000. This second edition constitutes a technical revision. The significant revisions with respect to the first edition are: - rectifying test conditions when dimming; - construction requirements; - measurement circuits and limits for HF leakage currents; - modification of the structure to become a standard exclusively for a.c. and d.c. central supplied electronic control gear for general lighting and Annex J cover centrally- supplied emergency control gear. This publication is to be read in conjunction with IEC 61347-1:2007. The contents of the corrigendum of September 2011 have been included in this copy.
- Standard47 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60929:2011 specifies performance requirements for electronic control gear for use on a.c. at 50 Hz or 60 Hz and/or d.c. supplies, both up to 1 000 V, with operating frequencies deviating from the supply frequency, associated with fluorescent lamps as specified in IEC 60081 and IEC 60901, and other fluorescent lamps for high-frequency operation. This fourth edition cancels and replaces the third edition published in 2006, IEC 60925 published in 1989, its Amendment 1 (1996) and its Amendment 2 (2001). This fourth edition constitutes a technical revision. The essential change with respect to the third edition is the extension to DC supplied control gear and the deletion of the requirements for digital signal control of electronic control gear. The contents of the corrigendum of September 2011 have been included in this copy.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
Amandma A1:2011 je dodatek k standardu SIST EN 61347-2-12:2006
This part of IEC 61347 specifies particular general and safety requirements for d.c. or a.c. supplied electronic ballasts. The supply comprises a.c. voltages up to 1000 V at 50 Hz/60 Hz. The type of ballast is an convertor that may contain igniting and stabilising elements for operation of a discharge lamp at d.c. or at a frequency that can deviate from the supply frequency. The lamps associated with the ballast are specified in IEC 60188 (High pressure mercury vapour lamps), IEC 60192 (Low pressure sodium vapour lamps), IEC 60662 (High pressure sodium vapour lamps), IEC 61167 (Metal halide lamps) and else for general purpose lighting. Ballasts for fluorescent lamps and for lamps for special applications like for theatre and for vehicles are excluded.
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment4 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment4 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard specifies performance requirements for ballasts for discharge lamps such as high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium vapour and metal halide lamps. Clauses 12 through 15 each detail specific requirements for a particular type of ballast. This standard covers inductive type ballasts for use on a.c. supplies up to 1 000 V at 50 Hz to 60 Hz associated with discharge lamps, having rated wattage, dimensions and characteristics as specified in the relevant IEC lamp standards.
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62386-205:2009 specifies a protocol and test procedures for the control by digital signals of electronic control gear associated with incandescent lamps. This Part 205 is intended to be used in conjunction with IEC 62386-101 and IEC 62386-102, which contain general requirements for the relevant product type (control gear or control devices).
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62386-206:2009 specifies a protocol and test methods for the control by digital signals of electronic control gear, associated with the conversion from digital signal into d.c. voltage. This Part 206 is intended to be used in conjunction with IEC 62386-101 and IEC 62386-102, which contain general requirements for the relevant product type (control gear or control devices).
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62386-203:2009 specifies a protocol and test procedures for the control of electronic control gear by digital signals used on a.c. or d.c. supplies, associated with discharge lamps (excluding fluorescent lamps). This Part 203 is intended to be used in conjunction with IEC 62386-101 and IEC 62386-102, which contain general requirements for the relevant product type (control gear or control devices).
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62386-204:2009 specifies a protocol and methods of test for the control by digital signals of electronic control gear for use on a.c. or d.c. supplies, associated with low voltage halogen lamps. This part 204 is intended to be used in conjunction with IEC 62386-101 and IEC 62386-102, which contain general requirements for the relevant product type (control gear or control devices).
- Standard39 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62386-208:2009 specifies a protocol and test methods for the control by digital signals of electronic control gear that switches its output only on and off. This Part 208 is intended to be used in conjunction with IEC 62386-101 and IEC 62386-102, which contain general requirements for the relevant product type (control gear or control devices).
- Standard74 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62386-202:2009 specifies a protocol and test procedures for the control by digital signals of electronic control gear for use on a.c. or d.c. supplies, associated with self-contained emergency lighting. This Part 202 is intended to be used in conjunction with IEC 62386-101 and IEC 62386-102, which contain general requirements for the relevant product type (control gear or control devices).
- Standard110 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
Specifies performance requirements for starting devices (starters and ignitors) for tubular fluorescent and other discharge lamps for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz which produce starting pulses not greater than 5 kV. Should be read in conjunction with EN 60926.
- Standard34 pagesEnglish languagesale 10% offe-Library read for1 day
This standard specifies performance requirements for ballasts excluding resistance types for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with tubular fluorescent lamps with pre-heated cathodes operated with or without a starter or starting device and having rated wattages, dimensions and characteristics as specified in EN 60081 and 60901. It applies to complete ballasts and their component parts such as resistors, transformers and capacitors.
- Standard35 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard specifies performance requirements for electronic step-down convertors for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with tungsten halogen lamps as specified in EN 60357 and other filament lamps.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard states the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including 2,5 kVAr, and not less than 0,1 µF, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m.
- Standard39 pagesEnglish languagesale 10% offe-Library read for1 day