CEN/TC 188/WG 3 - Safety requirements for conveyor belting

ISO 20238:2018 specifies a method of testing to determine the propensity of a conveyor belt to generate heat flame or glow when held stationary, under a given tension, in surface contact around a rotating driven steel drum.
ISO 20238:2018 describes means of varying the conveyor belt tension.
NOTE       For conveyor belts containing steel reinforcement, it may not be possible to conduct this test in full due to the inability of the conveyor belt to comply with the requirements of 7.2. In this case, premature termination according to 7.3 can be necessary.

from CEN/TC 188 N362: The revision of EN 14973 should be started to bring it in line with the revised EN 12881-1 and EN 12881-2. (see Resolution 2/2011). The experts present agree that an Annex should be added to EN 14973 to specify that Family approval for belts is possible. Resolution 2/2011: The experts present agree that general revision of EN 14973 and EN 12882 is needed due to the work being done on EN 12881-1 and EN 12881-2.

This European Standard specifies electrical and flammability safety requirements for general purpose conveyor belts not intended for use in underground installations and a means of categorizing conveyor belts in terms of the level of safety sought in their end use application. This European Standard does not provide electrical safety requirements for volume resistance which may be measured by the methods in EN ISO 21178 and which is relevant to some types of light conveyor belts.
This European Standard is not applicable to conveyor belts which are manufactured before the date of publication of this document by CEN.
NOTE 1   Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC, this being covered in EN 14973.
NOTE 2   EN 12882 is not a product standard but is intended to help users of conveyor belts to select the required electrical and flammability safety properties needed following a suitable risk assessment. No requirements are, therefore, included for marking, information to be supplied, etc., these matters being covered in relevant product standards such as EN ISO 14890 and EN ISO 15236 1.

EN 12881-1 describes four methods for measuring the propagation of a flame along a conveyor belt which has been exposed to a relatively high localized heat source such as a fire. The damage suffered by the conveyor belt, as well as its tendency to support combustion, is measured by observing the extent to which the fire spreads along the test piece.
Method A uses a test piece 2 m in length and consumes propane gas through the burner at the rate of (1,30 ± 0,05) kg per 10 min.
Method B uses a test piece 2,5 m in length and consumes propane gas through two burners mounted above and below the test piece trestle at the rate of (1,30 ± 0,05) kg per 10 min for each burner.
Method C uses a test piece 1,5 m in length and consumes propane gas through the burner at the rate of (565 ± 10) g per 50 min.
Method D uses a test piece 1,2 m in length and consumes propane gas through the burner at the rate of
150 l/hr (D1) or 190 l/hr (D2).

This document describes a method of testing for the assessment of fire propagation along a conveyor belt when the belt is exposed to a heat source.

This document specifies electrical and flammability safety requirements for general purpose conveyor belts not intended for use in underground installations and a means of categorizing conveyor belts in terms of the level of safety sought in their end use application. This document does not provide electrical safety requirements for volume resistance which may be measured by the methods in EN ISO 21178 and which is relevant to some types of light conveyor belts.
This document is not applicable to conveyor belts which are manufactured before the date of publication of this document by CEN.
NOTE 1   Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this document. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC, this being covered in EN 14973.
NOTE 2   prEN 12882 is not a product standard but is intended to help users of conveyor belts to select the required electrical and flammability safety properties needed following a suitable risk assessment. No requirements are, therefore, included for marking, information to be supplied, etc., these matters being covered in relevant product standards such as EN ISO 14890 and EN ISO 1523-1.

This document specifies electrical and flammability safety requirements for conveyor belts intended for use in underground installations, in the presence of flammable or non-flammable atmospheres.
Conveyor belts covered by this document and intended for use in flammable atmospheres are intended for use on conveyor belt installations (machinery in mines). The belt is a component or part of equipment, which can be incorporated into the conveyor, which is an equipment of Group I, Category M2, as defined in 3.2.2 of EN ISO 80079-36:2016.
This document is not applicable to light conveyor belts as described in EN ISO 21183-1:2006 nor is it applicable to conveyor belts which are manufactured before the date of publication of this document by CEN.
This document deals with those significant hazards detailed in A.1.
Attention is drawn to Annexes ZA and ZB.
NOTE   A summary of the requirements of this document is given in Table 2. This is intended for quick reference only.

This European Standard describes a method of test to determine the propensity of a conveyor belt to generate heat flame or glow when held stationary under a given tension, in surface contact around a rotating driven steel drum.
Means of varying the belt tension are described.
NOTE   For certain belt types, due to their construction, it may not be possible to conduct this test due to the inability of the belt to comply with the requirements of 6.2.3.

This European Standard specifies electrical and flammability safety requirements for conveyor belts intended for use in underground installations, in the presence of flammable or non-flammable atmospheres.
Conveyor belts covered by this European Standard and intended for use in flammable atmospheres are intended for use on conveyor belt installations (machinery in mines). The belt is a component, which will be incorporated into the conveyor, which is an equipment of Group I, Category M2, as defined in 3.2.2 of EN 13463-1:2001.
This European Standard is not applicable to light conveyor belts as described in EN 873 nor is it applicable to conveyor belts which are manufactured before the date of publication of this document by CEN.
This European Standard deals with those significant hazards detailed in A.1.
Attention is drawn to Annexes ZA and ZB.
NOTE   A summary of the requirements of this European Standard is given in Table 1.

This European Standard specifies electrical and flammability safety requirements for general purpose conveyor belts not intended for use in underground installations and a means of categorizing conveyor belts in terms of the level of safety sought in their end use application. This European Standard does not provide electrical safety requirements for volume resistance which may be measured by the methods in
EN ISO 21178 and which is relevant to some types of light conveyor belts.
This European Standard is not applicable to conveyor belts which are manufactured before the date of publication of this document by CEN.
NOTE 1   Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC, this being covered in EN 14973.
NOTE 2   EN 12882 is not a product standard but is intended to help users of conveyor belts to select the required electrical and flammability safety properties needed following a suitable risk assessment. No requirements are, therefore, included for marking, information to be supplied, etc., these matters being covered in relevant product standards such as EN ISO 14890 and EN ISO 15236-1.

This part of EN 12881 describes three methods for measuring the propagation of a flame along a conveyor belt which has been exposed to a relatively high localised heat source such as a fire. The damage suffered by the conveyor belt, as well as its tendency to support combustion, are measured by observing the extent to which the fire spreads along the test piece.
Method A uses a test piece 2 m in length and consumes propane gas through the burner at the rate of (1,30 ± 0,05) kg per 10 min.
Method B uses a test piece 2,5 m in length and consumes propane gas through two burners mounted above and below the test piece trestle at the rate of (1,30 ± 0,05) kg per 10 min for each burner.
Method C uses a test piece 1,5 m in length and consumes propane gas through the burner at the rate of (565 ± 10) g per 50 min.

This European Standard describes a method of test to determine the propensity of a conveyor belt to generate heat flame or glow when held stationary under a given tension, in surface contact around a rotating driven steel drum. Means of varying the belt tension are described. Note: For certain belt types, due to their construction, it may not be possible to conduct this test due to the inability of the belt to comply with the requirements of 6.2.3.

This European Standard specifies electrical and flammability safety requirements for
general purpose  conveyor belts not intended for use in underground installations
and a means of categorizing conveyor belts in terms of the level of safety sought in
their end use application.  This European Standard does not provide electrical safety
requirements for volume resistance which may be measured by the methods in EN
1637 and which is relevant to some types of light conveyor belts.
NOTE  Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC.

AFNOR - Translation error

This European Standard specifies electrical and flammability safety requirements for conveyor belts intended for use in underground installations, in the presence of flammable or non-flammable atmospheres.
Conveyor belts covered by this European Standard and intended for use in flammable atmospheres are intended for use on conveyor belt installations (machinery in mines). The belt is a component, which will be incorporated into the conveyor, which is an equipment of Group I, Category M2, as defined in 3.2.2 of EN 13463-1:2001.
This European Standard is not applicable to light conveyor belts as described in EN 873 nor is it applicable to conveyor belts which are manufactured before the date of publication of this document by CEN.
This European Standard deals with those significant hazards detailed in A.1.
Attention is drawn to Annexes ZA and ZB.
NOTE   A summary of the requirements of this European Standard is given in Table 1.

This part of EN 12881 describes three methods for measuring the propagation of a flame along a conveyor belt which has been exposed to a relatively high localised heat source such as a fire. The damage suffered by the conveyor belt, as well as its tendency to support combustion, are measured by observing the extent to which the fire spreads along the test piece.
Method A uses a test piece 2 m in length and consumes propane gas through the burner at the rate of (1,30 ± 0,05) kg per 10 min.
Method B uses a test piece 2,5 m in length and consumes propane gas through two burners mounted above and below the test piece trestle at the rate of (1,30 ± 0,05) kg per 10 min for each burner.
Method C uses a test piece 1,5 m in length and consumes propane gas through the burner at the rate of (565 ± 10) g per 50 min.

This document describes a method of testing for the assessment of fire propagation along a conveyor belt when the belt is exposed to a heat source.