SIST EN 16383:2017

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Wärmedämmstoffe für das Bauwesen - Bestimmung des hygrothermischen Verhaltens von außenseitigen Wärmedämm-Verbundsystemen mit Putzen (WDVS)Produits isolants thermiques pour le bâtiment - Détermination du comportement hygrothermique des systèmes d'isolation thermique extérieure par enduit sur isolant (ETICS)Thermal insulation products for building applications - Determination of the hygrothermal behaviour of external thermal insulation composite systems with renders (ETICS)91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:EN 16383:2016SIST EN 16383:2017en,fr,de01-januar-2017SIST EN 16383:2017SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16383
October
t r s x ICS
{ sä s r rä x r English Version
Thermal insulation products for building applications æ Determination of the hygrothermal behaviour of external thermal insulation composite systems with renders Produits isolants thermiques destinés aux applications du bâtiment æ Détermination du comportement hygrothermique des systèmes d 5isolation thermique
Wärmedämmstoffe für das Bauwesen æ Bestimmung des hygrothermischen Verhaltens von außenseitigen This European Standard was approved by CEN on
x August
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s x u z uã t r s x ESIST EN 16383:2017

± 5) °C. These devices shall meet the required test conditions described in Clause 7. 6 Test wall 6.1 Preparation of the test wall 6.1.1 General The kit(s) shall be applied on the substrate according to the instructions of the system holder. The configuration of the kit(s) to be tested shall be according to the worst case rules given in the relevant product standard. The thermal insulation product shall be fixed to the substrate and covered by the reinforced base coat. The perimeter edges of the test wall shall be wrapped/covered with the reinforced base coat. The upper 2/3 of the height of the test wall shall be covered additionally with one or more finishing layers according to Figure 1 and Figure 2. Within the lower 1/3 from the bottom edge shall be at least one horizontal joint between thermal insulation products (see “a” in Figure 1 and Figure 2). The distance between the horizontal joint and the 1/3 of the height of the test wall (see “b” in Figure 1 and Figure 2) shall be at least 200 mm. If the height of the thermal insulation product is bigger than 1/3 of the height of the test wall minus 200 mm, the thermal insulation product shall be cut properly. The test wall shall have openings according to 6.1.2 or 6.1.3. NOTE If given in the worst case rules of the relevant product standard, the whole test wall can be covered by finishing
...