SIST EN 14930:2007+A1:2009
(Main)Agricultural and forestry machinery and gardening equipment - Pedestrian controlled and hand-held machines - Determination of accessibility of hot surfaces
Agricultural and forestry machinery and gardening equipment - Pedestrian controlled and hand-held machines - Determination of accessibility of hot surfaces
This European Standard specifies a method for combustion engine driven pedestrian controlled and hand-held machines with or without back pack power unit used in agriculture, forestry and gardening to determine those parts of the surfaces identified by the product specific standards that are hot surfaces and can be touched unintentionally by an operator during normal operation.
This European Standard is only applicable together with product specific standards for the categories of machines specified above.
This European Standard does not specify which surfaces shall be assessed.
Land- und forstwirtschaftliche Maschinen und Gartengeräte - Mitgängergeführte und handgehaltene Maschinen - Bestimmung der Zugänglichkeit von heißen Oberflächen
Diese Europäische Norm enthält ein Verfahren für verbrennungsmotorgetriebene mitgängergeführte und
handgehaltene Maschinen mit oder ohne rückengetragener Antriebseinheit zur Verwendung in der Land- und
Forstwirtschaft sowie im Gartenbau zur Bestimmung der Teile von Oberflächen, die in einer produktspezifischen
Norm als heiß identifiziert worden sind und die beim normalen Betrieb durch die Bedienungsperson
unabsichtlich berührt werden können.
Diese Europäische Norm ist nur zusammen mit produktspezifischen Normen von oben beschriebenen Arten
von Maschinen anwendbar.
Diese Europäische Norm legt nicht fest, welche Oberflächen zu bewerten sind.
Matériels agricoles et forestiers et matériels de jardinage - Machines portables à la main et à conducteur à pied - Détermination du risque de contact avec les surfaces chaudes
La présente norme européenne spécifie une méthode pour les machines à moteur à combustion interne à conducteur
à pied et tenues à la main avec ou non le moteur porté à dos, utilisées dans l’agriculture, la foresterie et le jardinage,
afin de déterminer si les surfaces de ces éléments identifiées par les normes de produit spécifiques comme étant des
surfaces chaudes, peuvent être touchées par inadvertance par un opérateur pendant le fonctionnement normal.
La présente Norme européenne n'est applicable qu'avec des normes de produit spécifiques pour les catégories de
machines spécifiées ci-dessus.
La présente Norme européenne ne spécifie pas quelles surfaces doivent être évaluées.
Kmetijski in gozdarski stroji ter vrtna oprema - Nožno in ročno upravljani stroji - Opredelitev dostopa do vročih površinskih delov
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Land- und forstwirtschaftliche Maschinen und Gartengeräte - Mitgängergeführte und handgehaltene Maschinen - Bestimmung der Zugänglichkeit von heißen OberflächenMatériels agricoles et forestiers et matériels de jardinage - Machines portables à la main et à conducteur à pied - Détermination du risque de contact avec les surfaces chaudesAgricultural and forestry machinery and gardening equipment - Pedestrian controlled and hand-held machines - Determination of accessibility of hot surfaces65.060.01Kmetijski stroji in oprema na splošnoAgricultural machines and equipment in generalICS:Ta slovenski standard je istoveten z:EN 14930:2007+A1:2009SIST EN 14930:2007+A1:2009en,fr01-maj-2009SIST EN 14930:2007+A1:2009SLOVENSKI
STANDARDSIST EN 14930:20071DGRPHãþD
SIST EN 14930:2007+A1:2009
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14930:2007+A1
March 2009 ICS 65.060.01 Supersedes EN 14930:2007English Version
Agricultural and forestry machinery and gardening equipment - Pedestrian controlled and hand-held machines - Determination of accessibility of hot surfaces
Matériels agricoles et forestiers et matériels de jardinage - Machines portables à la main et à conducteur à pied - Détermination du risque de contact avec les surfaces chaudes
Land- und forstwirtschaftliche Maschinen und Gartengeräte - Mitgängergeführte und handgehaltene Maschinen - Bestimmung der Zugänglichkeit von heißen Oberflächen This European Standard was approved by CEN on 26 April 2007 and includes Amendment 1 approved by CEN on 29 December 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14930:2007+A1:2009: ESIST EN 14930:2007+A1:2009
EN 14930:2007+A1:2009 (E) 2 Contents Page Foreword .3 Introduction .4 1 Scope .5 2 Normative references .5 3 Terms and definitions .5 4 Principles .5 5 Test equipment .6 5.1 Temperature measuring equipment.6 5.2 Test cone .6 6 Test procedure .6 6.1 Determination of touchable surfaces .6 6.2 Determination of temperature of touchable surfaces .7 6.3 Determination of area for interrupted surfaces .7 7 Test acceptance .9 Annex A (informative)
Flowchart for the determination of inadvertent accessibility of hot surfaces of machinery . 10 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC, amended by Directive 98/79/EC . 11 Annex ZB (informative)
!!!!Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC"""" . 12 Bibliography . 13
SIST EN 14930:2007+A1:2009
EN 14930:2007+A1:2009 (E) 3 Foreword This document (EN 14930:2007+A1:2009) has been prepared by Technical Committee CEN/TC 144 “Tractors and machinery for agriculture and forestry”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This document includes Amendment 1, approved by CEN on 2008-12-29. This document supersedes EN 14930:2007. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document." According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
SIST EN 14930:2007+A1:2009
EN 14930:2007+A1:2009 (E) 4 Introduction This European Standard is a type C standard as stated in EN ISO 12100. Products with built-in engines or other heat-sources often show hot surfaces. If such a surface is touched by the unprotected skin, burning of the skin can occur. To avoid skin burning protective measures should be applied, especially in cases when the user of the product is not aware of the risk of burning. So it is essential to assess the risk of burning when using a product with a built-in heat source and to apply protective measures if necessary. This European Standard provides a test method to identify the touchable hot surfaces. Guidance for human response to contact with hot surfaces is given in EN 13202. C-type standard writers should consider making an exception from this test for parts or systems which can not be guarded (e.g. the inside and the end of exhaust pipe outlet). The aim of this European Standard is that it will be referenced in the type C standards. SIST EN 14930:2007+A1:2009
EN 14930:2007+A1:2009 (E) 5 1 Scope This European Standard specifies a method for combustio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.