SIST EN 485-2:2016/oprA1:2018
(Amendment)Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
This European Standard specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards.
The chemical composition limits of the alloys are specified in EN 573-3. Temper designations are defined in EN 515.
Aluminium und Aluminiumlegierungen - Bänder, Bleche und Platten - Teil 2: Mechanische Eigenschaften
Diese Europäische Norm legt die mechanischen Eigenschaften für Bleche, Bänder und Platten aus Aluminium und Aluminium-Knetlegierungen fest, die für die allgemeine Verwendung bestimmt sind.
Sie gilt nicht für gewalzte Halbzeuge in aufgerollter Form, die einem weiteren Walzvorgang unterzogen werden (Vorwalzbänder), oder für spezielle Erzeugnisse, wie z. B. profilierte, geprägte oder lackierte Bänder und Bleche oder für spezielle Anwendungen, wie z. B. Luft- und Raumfahrt, Getränkedosen und Wärmeaustauscher, für die die mechanischen Eigenschaften in gesonderten Europäischen Normen festgelegt sind.
Die Grenzwerte der chemischen Zusammensetzung der Legierungen sind in EN 573-3 festgelegt. Die Bezeichnungen der Werkstoffzustände sind in EN 515 definiert.
Aluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses - Partie 2 : Partie 2 : Caractéristiques mécaniques
La présente Norme européenne spécifie les caractéristiques mécaniques des tôles, bandes et tôles épaisses en aluminium corroyé et alliages d’aluminium corroyés pour applications courantes.
Elle ne s’applique pas aux demi-produits laminés, livrés en bobines, destinés à être relaminés (ébauches de relaminage), ni aux produits spéciaux, tels que les tôles et bandes ondulées, gravées, laquées, etc., ni aux applications spéciales, telles que la construction aéronautique, le boîtage et les échangeurs thermiques, pour lesquels les caractéristiques mécaniques sont spécifiées dans des Normes européennes séparées.
Les limites de composition chimique des alliages sont spécifiées dans l’EN 573-3. Les désignations des états métallurgiques sont définies sont définies dans l'EN 515.
Aluminij in aluminijeve zlitine - Pločevine, trakovi in plošče - 2. del: Mehanske lastnosti
General Information
- Status
- Not Published
- Public Enquiry End Date
- 14-Feb-2018
- Technical Committee
- INEK - Nonferrous metals
- Current Stage
- 98 - Abandoned project (Adopted Project)
- Start Date
- 08-Nov-2018
- Due Date
- 13-Nov-2018
- Completion Date
- 08-Nov-2018
Relations
- Consolidated By
SIST EN 485-2:2016+A1:2018 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties - Effective Date
- 18-Jan-2023
- Effective Date
- 01-Feb-2018
Overview
EN 485-2:2016/prA1 is a CEN draft amendment to EN 485-2:2016 covering the mechanical properties of wrought aluminium and aluminium alloy sheet, strip and plate for general engineering applications. The amendment corrects entries in the alloy list (notably Table 41 for EN AW-5657) and updates table page references. The standard excludes reroll stock (coiled semi-finished products), special surface or forming products (corrugated, embossed, painted) and special application families (e.g. aerospace, can stock, finstock) that are covered by separate standards.
Key Topics
- Scope and applicability: Defines the range of wrought aluminium sheet, strip and plate intended for general engineering use and clarifies which product types and applications are excluded.
- Mechanical properties: Establishes required tensile strength, yield strength, elongation, bend behaviour and hardness criteria for listed alloys and temper conditions.
- Amendment A1 highlights: Corrects mechanical-property entries for Alloy EN AW-5657 and adjusts the alloy table page references in clause 4.3.
- Referenced documents: Chemical composition limits are specified in EN 573-3 and temper designations follow EN 515. These cross-references ensure consistent alloy identification and tempering conventions.
Applications
EN 485-2:2016/prA1 is intended to support practical use of wrought aluminium sheet, strip and plate across engineering and manufacturing sectors where consistent mechanical data are required. Typical practical benefits include:
- Design reliability: Provides designers with validated tensile, yield and elongation data to size components and assess safety margins.
- Manufacturing control: Helps production engineers select appropriate alloys and tempers for forming, bending and fabrication processes.
- Procurement and QA: Enables clear purchase specifications and acceptance criteria based on harmonized mechanical property requirements.
The standard is most applicable to general engineering components and assemblies where the listed mechanical properties directly influence performance. It should not be used for products explicitly excluded by the scope, which are governed by other European standards.
Related Standards
- EN 573-3 - chemical composition limits for aluminium alloys (referenced by EN 485-2)
- EN 515 - temper designations and definitions (referenced by EN 485-2)
- EN 485 series - other parts addressing dimensions, tolerances and product specifics
By aligning mechanical property requirements with EN 573-3 and EN 515, EN 485-2:2016/prA1 promotes consistent material selection, reliable design data and harmonized quality assessment for wrought aluminium sheet, strip and plate used in general engineering.
Frequently Asked Questions
SIST EN 485-2:2016/oprA1:2018 is a draft published by the Slovenian Institute for Standardization (SIST). Its full title is "Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties". This standard covers: This European Standard specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards. The chemical composition limits of the alloys are specified in EN 573-3. Temper designations are defined in EN 515.
This European Standard specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards. The chemical composition limits of the alloys are specified in EN 573-3. Temper designations are defined in EN 515.
SIST EN 485-2:2016/oprA1:2018 is classified under the following ICS (International Classification for Standards) categories: 77.150.10 - Aluminium products. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 485-2:2016/oprA1:2018 has the following relationships with other standards: It is inter standard links to SIST EN 485-2:2016+A1:2018, SIST EN 485-2:2016. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase SIST EN 485-2:2016/oprA1:2018 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2018
$OXPLQLMLQDOXPLQLMHYH]OLWLQH3ORþHYLQHWUDNRYLLQSORãþHGHO 0HKDQVNH
ODVWQRVWL
Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
Aluminium und Aluminiumlegierungen - Bänder, Bleche und Platten - Teil 2:
Mechanische Eigenschaften
Aluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses - Partie 2 : Partie 2 :
Caractéristiques mécaniques
Ta slovenski standard je istoveten z: EN 485-2:2016/prA1
ICS:
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 485-2:2016
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
December 2017
ICS 77.150.10
English Version
Aluminium and aluminium alloys - Sheet, strip and plate -
Part 2: Mechanical properties
Aluminium et alliages d'aluminium - Tôles, bandes et Aluminium und Aluminiumlegierungen - Bänder,
tôles épaisses - Partie 2 : Partie 2 : Caractéristiques Bleche und Platten - Teil 2: Mechanische Eigenschaften
mécaniques
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 132.
This draft amendment A1, if approved, will modify the European Standard EN 485-2:2016. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 485-2:2016/prA1:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Modifications to 4.3, “List of alloys and their mechanical properties” . 5
2 Modifications to 4.3, Table 41, “Alloy EN AW-5657 [Al 99,85Mg 1]” . 7
European foreword
This document (EN 485-2:2016/prA1:2017) has been prepared by Technical Committee CEN/TC 132
“Aluminium and its
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...