iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 416-1:1999/A3:2003

(Amendment)

Single burner gas-fired overhead radiant tube heaters for non-domestic use - Part 1: Safety

Single burner gas-fired overhead radiant tube heaters for non-domestic use - Part 1: Safety

This standard is applicable to type A2, A3, B12, B13, B22, B23, C12, C13, C32 and C33 appliances intended for use in other than domestic dwellings, in which the supply of combustion air and/or the evacuation of the products of combustion is achieved by mechanical means located upstream of the draught diverter, if provided.

Gasgeräte-Heizstrahler - Dunkelstrahler mit einem Brenner mit Gebläse für gewerbliche und industrielle Anwendung - Teil 1: Sicherheit

Der zweite Absatz ist zu streichen und durch den folgenden Text zu ersetzen:
'Diese Norm ist für Geräte der Arten A2, A3, B12, B13, B22, B23, C12, C13, C32 und C33 anwendbar, die nicht für eine Verwendung in Wohnungen vorgesehen sind und bei denen die Zufuhr der Verbrennungsluft und/oder die Abführung der Abgase durch mechanische Einrichtungen erreicht wird, die, wenn vorgesehen, in Fließrichtung vor der Strömungssicherung angeordnet sind.'

Tubes radiants suspendus a monobruleur utilisant les combustibles gazeux a usage non-domestique - Partie 1: Sécurité

Stropna cevna sevala s plinskim gorilnikom, ki niso namenjena za ogrevanje stanovanj - 1. del: Varnost - Dopolnilo A3

General Information

Status
Withdrawn
Publication Date
28-Feb-2003
Withdrawal Date
09-Jun-2009
ICS
97.100.20 - Gas heaters
Technical Committee
PLN - Gas appliances for domestic use
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
05-Jun-2009
Due Date
28-Jun-2009
Completion Date
10-Jun-2009
Directive
90/396/EEC - Appliances burning gaseous fuels
Mandate
M/BC/CEN/89/6 - Standardization request to CEN concerning appliances burning gaseous fuels
Ref Project
EN 416-1:1999/A3:2002 - Single burner gas-fired overhead radiant tube heaters for non-domestic use - Part 1: Safety

Relations

Replaced By
SIST EN 416-1:2009 - Single burner gas-fired overhead radiant tube heaters for non-domestic use - Part 1: Safety
Effective Date
01-Jul-2009
Amends
SIST EN 416-1:1999 - Single burner gas-fired overhead radiant-tube heaters - Part 1: Safety
Effective Date
01-Mar-2003
Amends
SIST EN 416-1:1999 - Single burner gas-fired overhead radiant-tube heaters - Part 1: Safety
Effective Date
08-Jun-2022

Buy Standard

EN 416-1:1999/A3:2003EN 416-1:1999/A3:2003
PreviousNext
Amendment
EN 416-1:1999/A3:2003
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 416-1:1999/A3:2003
01-marec-2003
Stropna cevna sevala s plinskim gorilnikom, ki niso namenjena za ogrevanje
stanovanj - 1. del: Varnost - Dopolnilo A3
Single burner gas-fired overhead radiant tube heaters for non-domestic use - Part 1:
Safety
Gasgeräte-Heizstrahler - Dunkelstrahler mit einem Brenner mit Gebläse für gewerbliche
und industrielle Anwendung - Teil 1: Sicherheit
Tubes radiants suspendus a monobruleur utilisant les combustibles gazeux a usage non-
domestique - Partie 1: Sécurité
Ta slovenski standard je istoveten z: EN 416-1:1999/A3:2002
ICS:
97.100.20
SIST EN 416-1:1999/A3:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 416-1:1999/A3
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2002
ICS 97.100.20
English version
Single burner gas-fired overhead radiant tube heaters for non-
domestic use - Part 1: Safety
Tubes radiants suspendus à monobrûleur utilisant les Gasgeräte-Heizstrahler - Dunkelstrahler mit einem Brenner
combustibles gazeux à usage non-domestique - Partie 1: mit Gebläse für gewerbliche und industrielle Anwendung -
Sécurité Teil 1: Sicherheit
This amendment A3 modifies the European Standard EN 416-1:1999; it was approved by CEN on 14 March 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 416-1:1999/A3:2002 E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 416-1:1999/A3:2002 (E)
Foreword
This document (EN 416-1:1999/A3:2002) has been prepared by Technical Committee CEN/TC 180 "Non-domestic
gas-fired overhead radiant heaters", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by October 2002, and conflicting national standards shall be withdrawn at the latest
by October 2002.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EU Directive(s).
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard : Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,
Sweden, Switzerland and the United Kingdom.
This Amendment modifies EN 416-1:1999. It has been prepared to incorporate requirements for particular type C
appliances and to amend the requirements concerning automatic shut-off valves.
2

---------------------- Page: 3 ----------------------

EN 416-1:1999/A3:2002 (E)
1 Contents list
Delete title of annex B and replace with the following:
‘Annex B (normative) Appliance (flue) types’.
2 Clause 1 Scope
Delete the second paragraph and replace it with the following:
‘This standard is applicable to type A , A , B , B , B , B , C , C , C and C appliances intended for use in
2 3 12 13 22 23 12 13 32 33
other than domestic dwellings, in which the supply of combustion air and/or the evacuation of the products of
combustion is achieved by mechanical means located upstream of the draught diverter, if provided.’
3 Clause 2 Normative references
Add the following reference:
‘CR 1749:2001 European scheme for the classification of gas appliances according to the method of evacuation of the
products of combustion (Types)’.
4 Clause 3 Definitions
Insert the following definition after 3.1.12:
‘3.1.13
premixed burner
a burner in which the gas and a quantity of air, at least equal to that theoretically necessary for complete
combustion, are mixed before the flame port(s)’.
Amend the definition numbers as follows (the definitions are to be retained):
‘3.1.14 ignition burner
3.1.15 ignition device
3.1.16 primary aeration adjuster’.
Amend the title of 3.2 as follows:
‘3.2 combustion circuit’.
Insert the following definitions after 3.2:
‘3.2.1
combustion products circuit
circuit including the combustion chamber, the radiant tube, the combustion products evacuation duct and either the
fitting piece or the connection to the terminal, if any
3

---------------------- Page: 4 ----------------------

EN 416-1:1999/A3:2002 (E)
3.2.2
air supply and combustion products evacuation ducts
means for transporting combustion air to the burner and combustion products to the terminal or fitting piece.
NOTE  A fitting piece is not utilised by appliances of type C or of type C .
1 3
It is necessary to distinguish between:
completely surrounded ducts:
the combustion products evacuation duct is surrounded by combustion air throughout its length.
separate ducts:
the combustion products evacuation duct and the combustion air supply duct are neither concentric nor completely
surrounded ducts’.
Amend the definition numbers as follows (the definitions are to be retained):
‘3.2.3 combustion chamber
3.2.4 flue outlet
3.2.5 draught diverter’.
Insert the following definitions after 3.2.5 draught diverter:
‘3.2.6
terminal
device(s) fitted to the outside of the building, which are connected to the air supply and combustion products
evacuation ducts for type C and C appliances (one or two devices)
1 3
3.2.7
terminal guard
a device that protects the terminal from mechanical damage from outside influences’.
Insert the following definition after 3.3.1:
‘3.3.2
air proving device
a device intended to cause safety shutdown in the event of abnormal conditions of air admission or of combustion
products evacuation’.
Amend the definition numbers as follows (the definitions are to be retained):
‘3.3.3 programming unit
3.3.4 programme
3.3.5 flame detector
3.3.6 flame signal
3.3.7 flame supervision device
3.3.8 flame simulation
3.3.9 pressure governor (existing footnote is to be retained)
3.3.10 adjustable pressure governor
3.3.11 volume governor (existing footnote is to be retained)
4

---------------------- Page: 5 ----------------------

EN 416-1:1999/A3:2002 (E)
3.3.12 range-rating device
3.3.13 automatic shut-off device’.
5 Clause 4 Classification of appliances
4.3 Classification according to the mode of evacuation of the combustion products
Insert the following after 4.3.3:
‘4.3.4 Type C: An appliance in which the combustion circuit is sealed with respect to the inhabitable area of the
building in which the appliance is installed.
This standard applies to:
Type C : a type C appliance that is designed for connection via its ducts to a horizontal terminal, which at the same
1
time admits fresh air to the burner and discharges the products of combustion to the outside through orifices that
are either concentric or close enough to come under similar wind conditions.
Type C : a type C appliance incorporating a fan downstream of the combustion chamber/heat exchanger.
12 1
Type C : a type C appliance incorporating a fan upstream of the combustion chamber/heat exchanger.
13 1
Type C : a type C appliance that is designed for connection via its ducts to a vertical terminal, which at the same
3
time admits fresh air to the burner and discharges the products of combustion to the outside through orifices that
are either concentric or close enough to come under similar wind conditions.
Type C : a type C appliance incorporating a fan downstream of the combustion chamber/heat exchanger.
32 3
Type C : a type C appliance incorporating a fan upstream of the combustion chamber/heat exchanger.
33 3
See B.2 for the types of appliances identified above, in which the combustion air is supplied and/or in which the
products of combustion are evacuated either by natural draught or mechanical means.’
6 Clause 5 Constructional requirements
5.1.4 Means of sealing
Insert the following after 5.1.4.2:
‘5.1.4.3 Soundness of the combustion circuit (type C appliances)
Parts which have to be removed during routine service and affect the soundness of the appliance and/or its ducts,
shall be sealed by mechanical means, excluding pastes, liquids and tapes. The need for replacement of the seal(s),
following a cleaning or servicing operation as stated by the manufacturer, is permitted.
However, parts of the assembly that are not intended to be dismantled for maintenance may be joined in such a
way, that permanent soundness is assured during continuous service under normal conditions of use.
The ducts, bends, if any, and the terminal or fitting piece shall fit together correctly and shall form a stable
assembly. Parts intended to be dismantled for periodic servicing shall be designed and arranged so that soundness
is guaranteed after re-assembly.
Any fitting piece shall allow a sound connection to be made to the system intended for the evacuation of
combustion products and supply of air.’
5

---------------------- Page: 6 ----------------------

EN 416-1:1999/A3:2002 (E)
5.1.5 Supply of combustion air and evacuation of combustion products
Insert the following after the title:
‘5.1.5.1 General
All appliances shall be designed so that there is an adequate supply of combustion air during ignition and ove
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 15502-1:2022/AC:2023(Corrigendum)
Gas-fired heating boilers - Part 1: General requirements and tests
EN 15502-1:2021/AC:2022

This European Standard specifies the common requirements and test methods, as well as the classification, marking and energy labelling of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as “boilers”.
This European Standard is to be used in conjunction with the specific Parts 2 (Part 2-1 and following ones).
This European Standard applies to boilers of types B and C.
NOTE For further background information on appliance types see CEN/TR 1749:2014 [1].
a) that use one or more combustible gases of the three gas families at the pressures stated in EN 437;
b) where the temperature of the water is below or above 105 °C during normal operation;
c) where the maximum operating pressure in the water circuit does not exceed 6 bar;
d) which can give rise to condensation under certain circumstances;
e) which are declared in the instructions for installation to be either a "condensing" boiler or a "low temperature boiler" or a "standard boiler" or an "other boiler". If no declaration is given the boiler is to be considered both a "standard boiler" and an "other boiler";
NOTE The Ecodesign Directive defines "other boilers", "low temperature boilers" and "condensing boilers". The Boiler Efficiency Directive defines "standard boilers", "low temperature boilers" and "condensing boilers". Depending on the legislation applied, a boiler can be both "a standard boiler" and an "other boiler"."
f) which are intended to be installed inside a building or in a partially protected place;
g) which are intended to produce also hot water either by the instantaneous or storage principle as a single unit.
This European Standard applies to boilers designed for sealed water systems or for open water systems.
NOTE This general standard and the specific standards (see Part 2) provide requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard or a specific standard, the risk associated with this alternative construction will need to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This European Standard is not intended to cover appliances intended for connection to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex EE).
This European Standard is not intended to cover appliances designed and constructed to burn gas containing toxic components.

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15502-2-1:2022(Main)
Gas-fired central heating boilers - Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW
EN 15502-2-1:2022

This European Standard specifies, the requirements and test methods concerning, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as “boilers”.
This document is to be used in conjunction with FprEN15502-1:2020
This European Standard covers gas-fired central heating boilers from the types C1 up to C9 and the types B2, B3 and B5:
NOTE   For further background information on appliance types see EN 1749:2020.
a)   that have a nominal heat input (on the basis of net calorific value) not exceeding 1 000 kW;
b)   that use one or more combustible gases of the three gas families at the pressures stated in EN 437:2018;
c)   where the temperature of the heat transfer fluid does not exceed 105 °C during normal operation;
d)   where the maximum operating pressure in the water circuit does not exceed 6 bar;
e)   which can give rise to condensation under certain circumstances;
f)   which are declared in the instructions for installation to be either a “condensing” boiler or a "low temperature boiler" or a “standard boiler”; if no declaration is given the boiler is to be considered a “standard boiler”;
g)   which are intended to be installed inside a building or in a partially protected place;
h)   which are intended to produce also hot water either by the instantaneous or storage principle as a single unit.;
i)   which are designed for either sealed water systems or for open water systems;
j)   which are either modular boilers, or non modular boilers.
k) which are from the types C(10) that are equipped with a gas-air ratio control and that have a ∆pmax, saf(min) of 25 Pa, and C(11) that have condensing boiler modules that are equipped with a gas-air ratio control and that have a ∆pmax, saf(min) of 25 Pa."
NOTE   This European Standard provides requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard, the risk associated with this alternative construction needs to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This European Standard does not cover all the requirements for:
aa)   Appliances above 1000 kW
ab) Appliances that are intended to be connected to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex XC);"
ac)   Appliances using flue dampers;
ad)   Appliances of the types B21, B31, B51, C21, C41, C51, C61, C71, C81 ,C(12) and C(13);"
ae)   C7 appliances that have a nominal heat input (on the basis of net calorific value) exceeding 70 kW;
af)   Appliances incorporating flexible plastic flue liners;
ag)   C(10) boilers:
1)    without a gas-air ratio control, or
2)    which are non-condensing appliances, or
3)    which have a maximum safety pressure difference at minimum heat input not equal to 25 Pa (∆pmax, saf(min));
ah)   C(11) boilers that have boiler modules:
1)    without a gas-air ratio control, or
2)    which are non-condensing appliances, or
3)    which have a maximum safety pressure difference at minimum heat input not equal to 25 Pa (∆pmax, saf(min));"
ai)   Appliances intended to be connected to a (common) flue having mechanical extraction.
aj)   surface temperatures of external parts particular to children and elderly people
ak)   appliances that are intended to burn natural gases of the second family where hydrogen is added to the natural gas.
al)    appliances equipped with an adaptive combustion control function (ACCF).
am)   boilers intended to be installed in areas accessible to elderly people and children

  • Standard
    107 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    109 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16830:2022(Main)
Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Temperature Control function
EN 16830:2022

This European Standard specifies the safety, design, construction and performance requirements for Temperature Control Function (TCF) and Combustion Product Discharge Safety Device (TTB) intended for use with burners and appliances using gaseous or liquid fuels.
It also describes the test procedures for checking compliance with these requirements.
This European Standard is applicable to AC and DC supplied TCF and TTB (for TCF and TTB supplied by stand-alone battery system, battery systems for mobile applications or systems which are intended to be connected to DC supply networks, see Annex I).
This European Standard is applicable to electronically based TTB and TCF only.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 613:2022(Main)
Independent closed-fronted gas-fired type B11, type C11, type C31 and type C91 heaters
EN 613:2021

This document specifies the requirements and test methods for the construction, safety, marking and rational use of energy.
This standard is applicable to types B11, type C11, type C31 and type C91 appliances that burn gas and:
-   are closed-fronted;
-   incorporate a natural draught burner;
-   are connected directly to an open flue or to a device to evacuate the products of combustion (open-flued appliances, balanced-flued appliances);
-   are wall mounted, free-standing or built-in;
-   have a nominal heat input not exceeding 20 kW (based on the net calorific value).
This document is not applicable to:
-   open fronted appliances as specified in EN 13278;
-   decorative fuel effect appliances as specified in EN 509;
-   catalytic combustion appliances;
-   appliances in which the supply of combustion air and/or evacuation of products of combustion is achieved by mechanical means as specified in EN 1266;
-   ducted-air appliances;
-    appliances installed by means of a closure plate (see 3.3.3.3).
Matters related to quality assurance systems, tests during production and to certificates of conformity of auxiliary devices are not dealt with by this standard.

  • Standard
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    93 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14459:2022(Main)
Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Methods for classification and assessment
EN 14459:2021

This European Standard specifies methods for the classification and assessment of function blocks designed to operate burners and appliances burning gaseous or liquid fuels with particular regards to their fault behaviour and preventative measures.
This European Standard is applicable to new control function blocks, not covered by dedicated control standards.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15502-1:2022(Main)
Gas-fired heating boilers - Part 1: General requirements and tests
EN 15502-1:2021

This European Standard specifies the common requirements and test methods, as well as the classification, marking and energy labelling of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as “boilers”.
This European Standard is to be used in conjunction with the specific Parts 2 (Part 2-1 and following ones).
This European Standard applies to boilers of types B and C.
NOTE For further background information on appliance types see CEN/TR 1749:2014 [1].
a) that use one or more combustible gases of the three gas families at the pressures stated in EN 437;
b) where the temperature of the water is below or above 105 °C during normal operation;
c) where the maximum operating pressure in the water circuit does not exceed 6 bar;
d) which can give rise to condensation under certain circumstances;
e) which are declared in the instructions for installation to be either a "condensing" boiler or a "low temperature boiler" or a "standard boiler" or an "other boiler". If no declaration is given the boiler is to be considered both a "standard boiler" and an "other boiler";
NOTE The Ecodesign Directive defines "other boilers", "low temperature boilers" and "condensing boilers". The Boiler Efficiency Directive defines "standard boilers", "low temperature boilers" and "condensing boilers". Depending on the legislation applied, a boiler can be both "a standard boiler" and an "other boiler"."
f) which are intended to be installed inside a building or in a partially protected place;
g) which are intended to produce also hot water either by the instantaneous or storage principle as a single unit.
This European Standard applies to boilers designed for sealed water systems or for open water systems.
NOTE This general standard and the specific standards (see Part 2) provide requirements for boilers with known constructions. For boilers with any alternative constructions, which might not fully be covered by this standard or a specific standard, the risk associated with this alternative construction will need to be assessed.
An example of an assessment methodology, based upon risk assessment, is given in Clause 11.
This European Standard is not intended to cover appliances intended for connection to gas grids where the quality of the distributed gas is likely to vary to a large extent over the lifetime of the appliance (see Annex EE).
This European Standard is not intended to cover appliances designed and constructed to burn gas containing toxic components.

  • Standard
    213 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    215 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17175:2020(Main)
Gas-fired overhead radiant strip heaters and multi-burner continuous radiant tube heater systems for non-domestic use - Safety and energy efficiency
EN 17175:2019

This document specifies the requirements and test methods for the construction, safety, classification, marking and efficiency of non-domestic gas-fired overhead radiant strips heaters and multi-burner continuous radiant tube heater systems (referred to in the body of the text as the “system”) with each burner unit under the control of an automatic burner control system.
For radiant strip heaters incorporating a single burner, this standard is applicable to Type B22, B23, B52, B53, C12, C13, C32, C33 C52 and C53 appliances intended for use in other than domestic dwellings, in which the supply of combustion air and/or the evacuation of the products of combustion is achieved by mechanical means.
For multi-burner continuous radiant tube heater systems this standard is applicable to type B22, B52, and C52 appliances intended for use in other than domestic dwellings, in which the supply of combustion air and/or the evacuation of the products of combustion is achieved by mechanical means.
This standard also includes appliances incorporating a secondary heat exchanger in the flue system.
This standard is not applicable to:
a)   appliances designed for use in domestic dwelling;
b)   outdoor appliances;
c)   radiant strip heaters where the heat input is in excess of  300 KW (based on the net calorific value of the appropriate reference test gas);
d)   continuous radiant tube heater systems where the heat input of any individual burner unit is in excess of 70 kW (based on the net calorific value of the appropriate reference test gas);
e)   appliances having combustion products evacuation ducts that are non-metallic in the flue system – except ducts downstream of a possible additional condensing exhaust gas heat exchanger.
In addition, for heater systems incorporating multiple tube heaters this standard is not applicable to:
f)        appliances that are designed for continuous condensation within the flue system under normal      operating conditions – except downstream a possible additional exhaust gas heat exchanger.
This standard is applicable to appliances which are intended to be type tested.

  • Standard
    162 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    162 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    164 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17082:2020(Main)
Domestic and non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW
EN 17082:2019

This European Standard specifies the requirements and test methods for the safety and efficiency of gas fired air heaters with or without a fan to assist the transportation of combustion air and/or flue gases, hereafter referred to as "appliances".
This European Standard applies to Type A2, A3, B11, B11AS, B11BS, B12, B12AS, B12BS, B13, B13AS, B13BS, B14, B14AS, B14BS, B22, B23, B41, B41AS, B41BS, B42, B42AS, B42BS, B43, B43AS, B43BS, B44, B44AS, B44BS, B52, B53, C11, C12, C13, C21, C31, C32, C33, C41, C62 and C63 appliances with an input not exceeding 300 kW (net cv basis), intended for use in single unit residential dwellings and in other than single unit residential units. Provision of the heated air may be by means of ducting.
This European Standard does not apply to:
a)   dual purpose air conditioning appliances (heating and cooling);
b)   appliances where the air is heated by an intermediate fluid;
c)   portable or transportable forced convection appliances;
d)   domestic appliances for outdoor installation;
e)   appliances fitted with manual or automatic means of adjusting  the combustion products evacuation  by means of flue dampers;
f)   appliances having multiple heating units with a single draught diverter;
g)   appliances fitted with more than one flue outlet;
h)   appliances fitted with gas boosters;
i)   domestic appliances of type C22, C23, C42, C43, C52 and C53;
j)   C21 and C41 appliances for 3rd family gases;
NOTE For C41 appliances, see all requirements and test methods that are valid for C21 appliances, unless otherwise stated.
This European Standard is applicable to appliances which are intended to be type tested. It also includes requirements concerning the evaluation of conformity, including factory production control, but these requirements only apply to POCEDs and their associated terminals.

  • Standard
    193 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 419:2020(Main)
Gas-fired overhead luminous radiant heaters for non-domestic use - Safety and energy efficiency
EN 419:2019

This European Standard specifies the requirements and test methods for the construction, safety, rational use of energy, classification and marking of non-domestic gas-fired overhead luminous radiant heaters for environmental comfort, referred to in the body of the text as "appliances".
This European Standard is applicable to Type A1 and Type A3 appliances only (see 4.2.2) intended for use in other than residential dwellings:
a)   low gas pressure appliances operating at pressures up to and including 50 mbar;
b)   medium gas pressure appliances operating at pressures above 50 mbar and up to 2 bar.
This European Standard is not applicable to:
-   appliances designed for use in domestic dwellings;
-   outdoor appliances;
-   appliances of heat input in excess of 120 kW (based on the net calorific value of the appropriate reference gas);
This standard is applicable to appliances which are intended to be type tested.

  • Standard
    114 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 416:2020(Main)
Gas-fired overhead radiant tube heaters and radiant tube heater systems for non-domestic use - Safety and energy efficiency
EN 416:2019

This European Standard specifies the requirements and test methods for the construction, safety, classification, marking and efficiency of non-domestic gas-fired overhead radiant tube heaters incorporating a single burner and multiple burner systems (referred to in the body of the text as the "system") with each burner unit under the control of an automatic burner control system.
For radiant tube heaters incorporating a single burner, this standard is applicable to Type A2, A3, B12, B13, B22, B23, B42, B43, B52, B53, C12, C13, C32, C33, C52 and C53 appliances intended for use in other than domestic dwellings, in which the supply of combustion air and/or the evacuation of the products of combustion is achieved by mechanical means located upstream of the draught diverter, if provided.
For radiant tube heater systems incorporating multiple tube heater segments, this standard is applicable to Type B52, B52x, B53 and B53x systems intended for use in other than domestic dwellings, in which the supply of combustion air and/or the evacuation of the products of combustion is achieved by mechanical means.
This standard also includes appliances incorporating a secondary heat exchanger in the flue system.
This standard is not applicable to:
a)   appliances designed for use in domestic dwelling;
b)   outdoor appliances;
c)   appliances where the heat input of any individual burner unit is in excess of 120 kW (based on the net calorific value of the appropriate reference test gas);
d)   appliances having combustion products evacuation ducts that are non-metallic in the flue system - except ducts downstream of a possible additional condensing exhaust gas heat exchanger.
In addition, for heater systems incorporating multiple tube heaters this standard is not applicable to:
e)   appliances and systems that are designed for continuous condensation within the flue system under normal operating conditions - except downstream a possible additional exhaust gas heat exchanger.
This standard is applicable to systems which are intended to be type tested.

  • Standard
    167 pages
    English language
    sale 10% off
    e-Library read for
    1 day