iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN ISO 17683:2016

(Main)

Ships and marine technology - Ceramic weld backing for marine use (ISO 17683:2014)

Ships and marine technology - Ceramic weld backing for marine use (ISO 17683:2014)

This International Standard specifies the classification, dimension and appearance, performance, and test methods for ceramic weld backing. It also specifies marking, packaging, and storage. This International Standard is applicable to designing, manufacturing, testing, and accepting ceramic weld backing that are to be used in the double side form with single side weld, such as arc welding, gas welding, vertical gas welding, and submerged arc welding, and the shaping structural steel welding end for carbon steel, stainless steel, aluminium alloy, copper alloy, and so on.

Schiffe und Meerestechnik - Keramische Schweißbadsicherungen für maritime Anwendungen (ISO 17683:2014)

Navires et technologie maritime - Soutien de soudures en céramique (ISO 17683:2014)

L'ISO 17683:2014 spécifie la classification, les dimensions, l'aspect et les performances des supports envers de soudage en céramique, ainsi que les méthodes d'essai correspondantes. Elle contient également des spécifications relatives au marquage, à l'emballage et au stockage.
L'ISO 17683:2014 est applicable à la conception, à la fabrication, aux essais et à la réception des supports envers de soudage en céramique, destinés à être utilisés des deux côtés lors d'opérations de soudage à l'arc, de soudage aux gaz, de soudage vertical aux gaz, ou de soudage à l'arc sous flux réalisées d'un seul côté sur aciers de construction, aciers au carbone, aciers inoxydables, alliages d'aluminium, alliages de cuivre, etc.

Ladje in pomorska tehnologija - Keramična podložka za zvar za uporabo v pomorstvu (ISO 17683:2014)

Ta mednarodni standard določa klasifikacijo, dimenzije in videz, delovanje in metode preskušanja za keramično podložko za zvar. Določa tudi označevanje, embalažo in shranjevanje. Ta mednarodni standard velja za oblikovanje, proizvodnjo, preskušanje in sprejemanje keramičnih podložk za zvar, ki se bodo uporabljale v dvostranski obliki z enostranskim zvarom, na primer obločno varjenje, plinsko varjenje, navpično plinsko varjenje in zakrito obločno varjenje ter varjenje pri oblikovanju konstrukcijskega jekla za ogljikovo jeklo, nerjavno jeklo, aluminijevo zlitino, bakreno zlitino in podobno.

General Information

Status
Published
Public Enquiry End Date
08-Mar-2015
Publication Date
20-Dec-2015
ICS
47.020.10 - Hulls and their structure elements
Technical Committee
VAR - Welding
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
16-Dec-2015
Due Date
20-Feb-2016
Completion Date
21-Dec-2015
Ref Project
EN ISO 17683:2015 - Ships and marine technology - Ceramic weld backing for marine use (ISO 17683:2014)

Buy Standard

EN ISO 17683:2016EN ISO 17683:2016
PreviousNext
Standard
EN ISO 17683:2016
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 17683:2016
01-februar-2016
/DGMHLQSRPRUVNDWHKQRORJLMD.HUDPLþQDSRGORåND]D]YDU]DXSRUDERY
SRPRUVWYX ,62
Ships and marine technology - Ceramic weld backing for marine use (ISO 17683:2014)
Schiffe und Meerestechnik - Keramische Schweißbadsicherungen für maritime
Anwendungen (ISO 17683:2014)
Navires et technologie maritime - Soutien de soudures en céramique (ISO 17683:2014)
Ta slovenski standard je istoveten z: EN ISO 17683:2015
ICS:
47.020.10 Ladijski trupi in njihovi Hulls and their structure
konstrukcijski elementi elements
SIST EN ISO 17683:2016 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 17683:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 17683:2016


EN ISO 17683
EUROPEAN STANDARD

NORME EUROPÉENNE

December 2015
EUROPÄISCHE NORM
ICS 47.020.10
English Version

Ships and marine technology - Ceramic weld backing for
marine use (ISO 17683:2014)
Navires et technologie maritime - Soutien de soudures Schiffe und Meerestechnik - Keramische
en céramique pour usage maritime (ISO 17683:2014) Schweißbadsicherungen für maritime Anwendungen
(ISO 17683:2014)
This European Standard was approved by CEN on 11 June 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17683:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 17683:2016
EN ISO 17683:2015 (E)
Contents Page
European foreword . 3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 17683:2016
EN ISO 17683:2015 (E)
European foreword
The text of ISO 17683:2014 has been prepared by Technical Committee ISO/TC 8 “Ships and marine
technology” of the International Organization for Standardization (ISO) and has been taken over as EN
ISO 17683:2015 by Technical Committee CEN/TC 121 “Welding and allied processes” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be
withdrawn at the latest by June 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 17683:2014 has been approved by CEN as EN ISO 17683:2015 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 17683:2016

---------------------- Page: 6 ----------------------

SIST EN ISO 17683:2016
INTERNATIONAL ISO
STANDARD 17683
First edition
2014-02-01
Ships and marine technology —
Ceramic weld backing for marine use
Navires et technologie maritime — Soutien de soudures en céramique
Reference number
ISO 17683:2014(E)
©
ISO 2014

---------------------- Page: 7 ----------------------

SIST EN ISO 17683:2016
ISO 17683:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 17683:2016
ISO 17683:2014(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 1
5 Dimensions and appearance . 2
5.1 General . 2
5.2 Dimensions . 2
5.3 Appearance . 2
6 Performance and test . 2
6.1 Moisture absorption rate . 2
6.2 Refractoriness . 3
6.3 Chemical composition . 3
6.4 Adhesive aluminium foil tape . 3
6.5 Metal cases. 3
7 Type approval test . 4
7.1 General . 4
7.2 Test items . 4
7.3 Acceptance criteria . 4
8 Acceptance test . 4
8.1 Test items . 4
8.2 Acceptance criteria . 4
9 Marking, packaging, and storage . 5
9.1 Marking . 5
9.2 Packaging . 5
9.3 Storage . 5
© ISO 2014 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 17683:2016
ISO 17683:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national stand
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1502:2023(Main)
Inland navigation vessels - Boarding stairs
EN 1502:2023

This document applies to boarding stairs for inland navigation vessels. Boarding stairs are used on inland navigation vessels for a safe transition into ship's boats, safe disembarking to the shore or a safe crossing over onto vessels with lower decks.
This document specifies safety requirements on the design, dimensions and strength and test methods for outboard stairs.
Boarding stairs are designed for vessels having a boarding height greater than 1,5 m above the light water-line. They can be used up to a height of around 3,0 m above the light water-line.
Boarding stairs are not intended for use by passengers.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17361:2023(Main)
Inland navigation vessels - Outboard ladders
EN 17361:2023

This document applies to outboard ladders for inland navigation vessels. Outboard ladders are used on inland navigation vessels having great side heights to facilitate safe climbing into ship's boats, safe disembarking or safe crossing over onto vessels in the case of significantly different boarding heights.
This document specifies safety requirements on design, dimensions and strength and test conditions for outboard ladders.
Outboard ladders are intended for that range where boarding stairs according to EN 1502 are not sufficient in length. This range starts at a boarding height of approximately at 2,8 m above the light water-line.
Boarding ladders are not intended for use by passengers.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 12215-7:2021(Main)
Small craft - Hull construction and scantlings - Part 7: Determination of loads for multihulls and of their local scantlings using ISO 12215-5 (ISO 12215-7:2020)
EN ISO 12215-7:2020

This document defines the dimensions, local design pressures and global loads acting on multihull
craft with a hull length (LH) or load line length of up to 24 m (see Note). It considers all parts of the
craft that are assumed watertight or weathertight when assessing stability, freeboard and buoyancy in
accordance with ISO 12217 (all parts). Scantlings corresponding to the local design pressures are then
assessed using ISO 12215-5.
NOTE The load line length is defined in the OMI "International Load Lines Convention 1966/2005", it can
be smaller than LH for craft with overhangs. This length also sets up at 24 m the lower limit of several IMO
conventions.
This document is applicable to multihulls built from the same materials as in ISO 12215-5, in intact
condition, and of the two following types:
— recreational craft, including recreational charter vessels;
— commercial craft and workboats.
It is not applicable to multihull racing craft designed only for professional racing.
This document is applicable to the structures supporting windows, portlights, hatches, deadlights
and doors.
For the complete scantlings of the craft, this document is intended to be used in conjunction with
ISO 12215-8 for rudders, ISO 12215-9 for appendages of sailing craft and ISO 12215-10 for rig loads and
rig attachment in sailing craft. ISO 12215-6 can be used for additional details.
Throughout this document, unless otherwise specified, dimensions are in (m), areas in (m2), masses
in (kg), forces in (N), moments in (Nm), Pressures in (kN/m2) (1 kN/m2 = 1 kPa), stresses and elastic
modulus in (N/mm2) (1 N/mm2 = 1 MPa).

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 12215-10:2021(Main)
Small craft - Hull construction and scantlings - Part 10: Rig loads and rig attachment in sailing craft (ISO 12215-10:2020)
EN ISO 12215-10:2020

This document specifies methods for the determination of:
— the design loads and design stresses on rig elements; and
— the loads and scantlings of rig attachments and mast steps/pillars;
on monohull and multihulls sailing craft.
It also gives, in Annexes, "established practices" for the assessment of mast steps/pillars or chainplates
NOTE 1 Other engineering methods can be used provided the design loads and design stresses are used.
This document is applicable to craft with a hull length LH up to 24 m but it can also be applied to craft up
to 24 m load line length.
NOTE 2 The load line length is defined in the OMI "International Load Lines Convention 1966/2005", it is
smaller than LH. This length also sets up, at 24 m, the lower limit of several IMO conventions.
Scantlings derived from this document are primarily intended to apply to recreational craft, including
charter vessels.
This document is not applicable to racing craft designed only for professional racing.
This document only considers the loads exerted when sailing. Any loads that may result from other
situations are not considered in this document.
Throughout this document, and unless otherwise specified, dimensions are in (m), areas in (m2), masses
in (kg), forces in (N), moments in (N m), stresses and elastic modulus in N/mm2 (1 N / mm2 = 1 Mpa).
Unless otherwise stated, the craft is assessed in fully loaded ready for use condition.

  • Standard
    87 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    74 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17360:2020(Main)
Inland navigation vessels - Stanchions and holders for tiltable and detachable railings
EN 17360:2020

This document is applicable to stanchions and holders of tiltable and detachable railings (railing type CT and CD according to EN 711 in work areas) for inland navigation vessels. These railings are situated in the side deck areas, where a permanently fitted railing can be an obstacle for loading/discharging operations.
The stanchions are designed for use with handrails and intermediate guardrails made of wire ropes.
Dimensions marked with a ● are safety dimensions and correspond to the stipulations in EN 711.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 12215-5:2019(Main)
Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls, design stresses, scantlings determination (ISO 12215-5:2019)
EN ISO 12215-5:2019

This document defines the dimensions, design local pressures, mechanical properties and design
stresses for the scantlings determination of monohull small craft with a hull length (LH) or a load line
length (see NOTE 1) of up to 24 m. It considers all parts of the craft that are assumed to be watertight or
weathertight when assessing stability, freeboard and buoyancy in accordance with ISO 12217.
NOTE 1 The load line length is defined in the IMO "International Load Lines Convention 1966/2005", it
can be larger than LH for craft with overhangs. This length also sets up at 24 m the lower limit of several IMO
conventions.
The main core of this document determines the local design pressures and stresses for monohulls and
details the possible scantlings methods derived from these pressures and stresses, both for monohulls
and multihulls (see NOTE 2). The assessment process requires, where relevant, the application of
Annexes.
This document is applicable to small craft, in intact condition, of the two following types:
— recreational craft, including recreational charter vessels;
— small commercial craft and workboats, see Clause 12 and Annex J.
It is not applicable to racing craft designed only for professional racing.
NOTE 2 Local pressures and stresses for multihulls are given in ISO 12215-7.
This document is applicable to the structures supporting windows, portlights, hatches, deadlights,
and doors.
For the complete scantlings of the craft, this document is intended to be used with ISO 12215-8 for
rudders, ISO 12215-9 for appendages and ISO 12215-10 for rig loads and rig attachments.
This document covers small craft built from the following materials:
— fibre-reinforced plastics, either in single skin or sandwich construction;
— aluminium or steel alloys;
— glued wood or plywood (single skin or sandwich), excluding traditional wood construction;
— non-reinforced plastics for craft with a hull length less than 6 m (see Annex D).
Throughout this document, unless otherwise specified, dimensions are in (m), areas in (m2), masses
in (kg), forces in (N), moments in (N.m), pressures in kN/m2 (1 kN/m2 = 1 kPa), stresses and elastic
modulus in N/mm2 (1 N/mm2 = 1 Mpa). Max(a;b;c) means that the required value is the maximum of a,
b, and c; and min(d;e;f) means that the required value is the minimum of d, e, and f.

  • Standard
    136 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 12215-1:2018(Main)
Small craft - Hull construction and scantlings - Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate (ISO 12215-1:2000)
EN ISO 12215-1:2018

This part of ISO 12215 is applicable to thermosetting resins and glass-fibre reinforcement used in the construction of
small craft with a length of the hull of up to , in accordance with ISO 8666. This part of ISO 12215 specifies
the minimum requirements for material properties of glass reinforcement and resin matrix and the reference laminate
made thereof.
This part of ISO 12215 may be applicable to materials other than those specified, provided that the minimum requirements
and properties of the reference laminate are met.
NOTE The underlying reason for preparing this International Standard is to harmonize existing standards and recommended
practices for loads on the hull and the dimensioning of small craft because they differ too considerably and thus limit general
worldwide acceptability of boats.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 12215-9:2018(Main)
Small craft - Hull construction and scantlings - Part 9: Sailing craft appendages (ISO 12215-9:2012)
EN ISO 12215-9:2018

This part of ISO 12215 defines the loads and specifies the scantlings of sailing craft appendages on monohull
sailing craft with a length of hull, LH, of up to 24 m, measured according to ISO 8666. It gives
 design stresses,
 the structural components to be assessed,
 load cases and design loads for keel, centreboard and their attachments,
 computational methods and modelling guidance, and
 the means for compliance with its provisions.

  • Standard
    85 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 12215-2:2018(Main)
Small craft - Hull construction and scantlings - Part 2: Materials: Core materials for sandwich construction, embedded materials (ISO 12215-2:2002)
EN ISO 12215-2:2018

This part of ISO 12215 specifies requirements for core materials for structural use and materials that are embedded
in sandwich construction. It is applicable to small craft with a hull length (LH) according to ISO 8666 of up to 24 m.
NOTE The underlying reason for preparing this part of ISO 12215 is that sandwich structures of small craft require careful
selection of core materials from a multitude of choices, and that the manufacturing has to follow certain procedures to achieve
the intended long-term durability under the expected loads and environmental conditions.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 12215-8:2018(Main)
Small craft - Hull construction and scantlings - Part 8: Rudders (ISO 12215-8:2009, including Cor 1:2010)
EN ISO 12215-8:2018

This part of ISO 12215 gives requirements on the scantlings of rudders fitted to small craft with a length of hull,
LH, of up to 24 m, measured according to ISO 8666. It applies only to monohulls.
This part of ISO 12215 does not give requirements on rudder characteristics required for proper steering
capabilities.
This part of ISO 12215 only considers pressure loads on the rudder due to craft manoeuvring. Loads on the
rudder or its skeg, where fitted, induced by grounding or docking, where relevant, are out of scope and need
to be considered separately.
NOTE Scantlings derived from this part of ISO 12215 are primarily intended to apply to recreational craft including
charter craft.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day