SIST EN 546-4:2007

SLOVENSKI STANDARD
01-marec-2007
1DGRPHãþD
SIST EN 546-4:1998
Aluminij in aluminijeve zlitine - Folija - 4. del: Zahtevane posebne lastnosti
Aluminium and aluminium alloys - Foil - Part 4: Special property requirements
Aluminium und Aluminiumlegierungen - Folien - Teil 4: Besondere
Eigenschaftsanforderungen
Aluminium et alliages d'aluminium - Feuille mince - Partie 4 : Exigences de propriétés
particulieres
Ta slovenski standard je istoveten z: EN 546-4:2006
ICS:
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 546-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2006
ICS 77.150.10 Supersedes EN 546-4:1997
English Version
Aluminium and aluminium alloys - Foil - Part 4: Special property
requirements
Aluminium et alliages d'aluminium - Feuille mince - Partie 4 Aluminium und Aluminiumlegierungen - Folien - Teil 4:
: Exigences de propriétés particulières Besondere Eigenschaftsanforderungen
This European Standard was approved by CEN on 25 November 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 546-4:2006: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Scope.4
2 Normative references.4
3 Terms and definitions .4
4 Application of special property testing .4
5 Porosity.5
5.1 Test principle.5
5.2 Test method.5
5.3 Acceptance values.6
5.4 Sampling and frequency of testing.6
6 Wettability.6
6.1 Test principle.6
6.2 General test conditions.6
6.3 Test procedures.7
6.4 Frequency of testing .10
7 Stickiness.10
7.1 Test principle.10
7.2 Test method.10
7.3 Acceptance criteria.11
7.4 Frequency of testing .11
8 Burst strength.11
9 Erichsen cupping test.12
9.1 Test principle.12
9.2 Test method.12
9.3 Acceptance criteria.12
9.4 Frequency of testing .12
Bibliography .13

Table
Table 1 — Applicability of special property tests to product group .5

Foreword
This document (EN 546-4:2006) has been prepared by Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at
the latest by June 2007.
This document supersedes EN 546-4:1997.
Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 6 "Foil and
finstock" to revise EN 546-4:1997.
The following modifications have been made:
 Clause 3: reference to EN 12258-1:1998 has been added, the definition of perforation has been deleted;
 Clause 4: Table 1: limitation of pinholes (6 µm to 20 µm) detection range for light gauge converter double
roller (6 µm to 70 µm) has been deleted;
 Clause 6: addition of test by use of Cotton Wool Pad (6.3.4);
 Figure 3 second Figure has been added.
EN 546 comprises the following parts under the general title "Aluminium and aluminium alloys - Foil":
 Part 1: Technical conditions for inspection and delivery
 Part 2: Mechanical properties
 Part 3: Tolerances on dimensions
 Part 4: Special property requirements
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardised
standard products under reasonable and not discriminatory conditions, then this product shall be removed
from the corresponding standard.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
1 Scope
This document specifies the requirements for special properties of wrought aluminium and wrought aluminium
alloy foil and their tests. It applies to flat rolled products.
It does not apply to lacquered, painted, embossed or laminated products.
The technical conditions for inspection and delivery of foil are specified in EN 546-1.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 12258-1:1998, Aluminium and aluminium alloys — Terms and definitions — Part 1: General terms
EN ISO 20482, Metallic materials — Sheet and strip — Erichsen cupping test (ISO 20482:2003)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following
apply.
3.1
pinholes (foil)
randomly distributed voids in foil of gauge 6 µm to 20 µm of normally round or oval shape with a maximum
diameter < 0,2 mm
3.2
roll holes (foil)
voids with a maximum diameter > 0,2 mm which occur at regular intervals throughout the rolled coil length
4 Application of special property testing
The applicability of tests for special properties of foil products is given in Table 1.
The tests shall only be carried out when agreed between supplier and purchaser and stated on the order.
Table 1 — Applicability of s
...