SIST EN 1629:2021

SLOVENSKI STANDARD
01-september-2021
Nadomešča:
SIST EN 1629:2012+A1:2016
Vrata, okna, obešene fasade, mreže in polkna - Protivlomna odpornost - Preskusna
metoda za ugotavljanje odpornosti proti dinamičnim obremenitvam
Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance -
Test method for the determination of resistance under dynamic loading
Türen, Fenster, Vorhangfassaden, Gitterelemente und Abschlüsse - Einbruchhemmung -
Prüfverfahren für die Ermittlung der Widerstandsfähigkeit unter dynamischer Belastung
Blocs-portes pour piétons, fenêtres, façades rideaux, grilles et fermetures - Résistance à
l'effraction - Méthode d'essai pour la détermination de la résistance à la charge
dynamique
Ta slovenski standard je istoveten z: EN 1629:2021
ICS:
13.310 Varstvo pred kriminalom Protection against crime
91.060.50 Vrata in okna Doors and windows
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 1629
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2021
EUROPÄISCHE NORM
ICS 13.310; 91.060.50 Supersedes EN 1629:2011+A1:2015
English Version
Pedestrian doorsets, windows, curtain walling, grilles and
shutters - Burglar resistance - Test method for the
determination of resistance under dynamic loading
Blocs-portes pour piétons, fenêtres, façades rideaux, Türen, Fenster, Vorhangfassaden, Gitterelemente und
grilles et fermetures - Résistance à l'effraction - Abschlüsse - Einbruchhemmung - Prüfverfahren für die
Méthode d'essai pour la détermination de la résistance Ermittlung der Widerstandsfähigkeit unter
à la charge dynamique dynamischer Belastung
This European Standard was approved by CEN on 19 March 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1629:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Apparatus . 5
4.1 Test rig . 5
4.2 Pendulum impactor . 6
4.3 Suspension system . 6
4.4 Sub-frame. 6
4.5 Measuring equipment . 6
5 Test specimen. 7
5.1 General . 7
5.2 Preparation and examination of the test specimen . 7
6 Procedure . 8
6.1 Test room climate . 8
6.2 Impact points, directions and test sequence . 8
6.2.1 General . 8
6.2.2 Group 1, Group 2 and Group 3 products . 8
6.2.3 Group 4 products . 9
6.3 Impact test procedure . 10
7 Expression of results . 10
8 Test report . 10
Annex A (informative) Test equipment and impact points . 12
Annex B (informative) Test sequence for dynamic loading test in resistance classes 1 to 3 . 41

European foreword
This document (EN 1629:2021) has been prepared by Technical Committee CEN/TC 33 “Doors, windows,
shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by December 2021, and conflicting national standards
shall be withdrawn at the latest by December 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1629:2011+A1:2015.
Significant changes in this revision are:
a) updated editions of Normative References;
b) clarification of combined impact points in 6.2.1.
This document is one of a series of standards for burglar resistant pedestrian doorsets, windows, curtain
walling, grilles and shutters. The other standards in the series are:
— EN 1627:2021, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar
resistance — Requirements and classification;
— EN 1628:2021, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar
resistance — Test method for the determination of resistance under static loading;
— EN 1630:2021, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar
resistance — Test method for the determination of resistance to manual burglary attempts.
The test described in this document is intended to simulate physical attacks, e.g. shoulder charge, kicking.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
1 Scope
This document specifies a test method for the determination of resistance to dynamic loading in order to
assess the burglar resistant properties of pedestrian doorsets, windows, curtain walling, grilles and
shutters. It is applicable to the following opening functions: turning, tilting, folding, turn-tilting, top or
bottom hung, sliding (horizontally and vertically), projecting, pivoted (horizontally and vertically) and
rolling as well as non-openable constructions.
It is acknowledged that there are two aspects to the burglar resistance performance of construction
products, their normal resistance to forced operation and their ability to remain fixed to the building.
This test method does not evaluate the performance of the fixing to the building.
The manufacturer's installation instructions will give guidance on the fixing of the product.
An example for the contents of the manufacturer's installation instructions is given in EN 1627:2021,
Annex A.
This document does not apply to walls and roofs, as well as for doors, gates and barriers, intended for
installation in areas in the reach of persons, and for which the main intended uses are giving safe access
for goods and vehicles accompanied or driven by persons in industrial, commercial or residential
premises, as covered by EN 13241:2003+A2:2016.
NOTE It is important that construction products that can be reached or driven through by vehicles are
protected by appropriate measures such as barriers, extensible ramps, etc.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 356:1999, Glass in building — Security glazing — Testing and classification of resistance against
manual attack
EN 1627:2021, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar resistance —
Requirements and classification
EN 1628:2021, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar resistance —
Test method for the determination of resistance under static loading
EN 1630:2021, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar resistance —
Test method for the determination of resistance to manual burglary attempts
EN 12216:2018, Shutters, external blinds, internal blinds — Terminology, glossary and definitions
EN 12519:2018, Windows and pedestrian doors — Terminology
EN 12600:2002, Glass in building — Pendulum test — Impact test method and classification for flat glass
EN 13119:2016, Curtain walling — Terminology
EN 13241:2003+A2:2016, Industrial, commercial, garage doors and gates — Product standard,
performance characteristics
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1627:2021, EN 12519:2018, EN
12216:2018 and EN 13119:2016 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at https://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
test specimen
complete, fully functioning construction product as detailed in the scope of this document
3.2
sub-frame
standard surrounding frame into which the test specimen is mounted for testing purpose
3.3
test rig
surrounding substantial steel frame with movable steel supports into which the sub-frames containing
test specimens of various dimensions can be mounted
3.4
impacting unit
impactor suspended by means of a suitable steel cable, as a pendulum of fixed length, with a release hook
and height regulating device
3.5
impactor
body used to strike the test specimen
3.6
impact point
position on the surface of the test specimen where the dynamic load is applied
4 Apparatus
4.1 Test rig
The test rig into which test specimens of various dimensions can be mounted is shown in Annex A,
Figure A.1. The stiffness of the rig shall be such that a 15 kN force applied to any of the defined points and
normal to the plane of the frame will not cause a deflection of more than 5 mm and shall not affect the
results of the test. The test rig shall not impede the execution of the test.
4.2 Pendulum impactor
The pendulum impactor, conforming to EN 12600:2002, is listed with individual components and
pictured in Annex A, Figure A.2 and Figure A.3. The impactor shall consist of two pneumatic tyres (type
) inflated to a pressure of (0,35 ± 0,02) MPa with round section and flat longitudinal tread
3.50 R8 4PR
and shall be suspended by means of a suitable steel cable giving a minimum pendulum length of
1 000 mm, with a release hook and height regulating device. The tyres shall be fitted to the rims (type
250-8) of wheels that carry two steel weights of equal mass. The weights shall be dimensioned so that
the total mass of the impactor is (50 ± 0,1) kg (excluding the steel cable and release hook) and the weights
do not have any contact with the test specimen during the impact.
The drop height shall be the vertical height through which the centre of gravity of the impactor falls, with
a tolerance of ± 10 mm. The impactor support point shall allow the impactor to strike the test specimen
at all relevant points. The complete pendulum impactor unit shall be adjustable and may be installed
either on the test rig, as shown in Annex A, Figure A.1, or as an independent unit.
4.3 Suspension system
The suspension system shall conform to EN 12600:2002.
4.4 Sub-frame
The sub-frame shall simulate the support given to the product when installed into a building. It shall
typically consist of the following:
a) for group 1 to group 4 products, a rectangular minimum metal tube 120 mm × 120 mm × 5 mm or a
rectangular timber frame minimum 100 mm × 70 mm;
NOTE High quality wood, e.g. glue laminated timber.
b) additionally, for group 3 products and group 4 products a steel tube 40 mm × 40 mm × 3 mm and a
base plate of 8 mm steel, consisting of several segments which shall be removable for the purposes
of loading, if necessary.
4.5 Measuring equipment
The measuring equipment consists of the following:
a) suitable device for measuring the drop height;
b) equipment for determining temperature and relative humidity;
c) gap gauge C, as shown in EN 1628:2021, Figure A.14.
The dimensions of the gap gauge shall have a tolerance of ± 1 mm.

Tyre 3.50-R8 4PR can be used for the pendulum test. Tyre 3.50-R8 4PR is the trade name of a product supplied by
Vredestein BV. This information is given for the convenience of users of this European Standard and does not
constitute an endorsement by CEN of the product named. Equivalent products may be used if they can be shown to
lead to the same results.
5 Test specimen
5.1 General
The test specimen shall be a functioning product complete with its frames, hardware, guide rails, curtain,
tube, roller box and accessories, as appropriate.
The test specimen shall be fixed square and plumb and without twist or bend into a sub-frame. The
installation shall be in accordance with the manufacturer’s installation instructions relevant for the given
subframe material/dimensions (see examples in Figure A.4 to A.20 b).
For the purposes of this document, the test specimen shall be glazed according to the relevant glazing
resistance class of EN 356:1999, corresponding to the resistance class of the construction product
according to EN 1627:2021, as shown in Table 1 of this document.
For the purpose of this test, the glass pane offering the highest security level shall be placed on the impact
side of the product. The test specimen used in this test may also be used for the pre-test in accordance
with EN 1630:2024, provided that any damage caused by these tests will not affect the result of the pre-
test. See EN 1627:2021, Clause 11.
Table 1 — Test specimen glazing requirements
Minimum resistance class of glazing according to EN
Resistance class
356:1999 fitted on the test specimen for testing purpose
RC 1 N P4 A
RC 1 P4 A
RC 2 N P4 A
RC 2 P4 A
RC 3 P5 A
Products that use infilling other than glass shall be tested with the intended infill material. The test
specimen used in the static test in accordance with EN 1628:2021 may also be used for this test.
Products that are intended to be installed in orientations other than vertical (e.g. roof lights) shall be
installed in the vertical orientation for the purpose of this test.
Should the glass break during any tests, the test programme shall proceed with the broken glass in situ
...