SIST EN 13880-8:2019

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Heiß verarbeitbare Fugenmassen - Teil 8: Prüfverfahren zur Bestimmung der Gewichtsänderung nach TreibstofflagerungProduits de scellement de joints appliqués à chaud - Partie 8 : Méthode d'essai pour la détermination de la variation de masse selon leur résistance aux hydrocarbures de produits de scellement de joints après immersion dans des hydrocarburesHot applied joint sealants -
Part 8: Test method for the determination of the change in weight of fuel resistance joint sealants after fuel immersion93.080.20Materiali za gradnjo cestRoad construction materials91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 13880-8:2018SIST EN 13880-8:2019en,fr,de01-marec-2019SIST EN 13880-8:2019SLOVENSKI
STANDARDSIST EN 13880-8:20041DGRPHãþD



SIST EN 13880-8:2019



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13880-8
December
t r s z ICS
{ uä r z rä t r Supersedes EN
s u z z ræ zã t r r uEnglish Version
Hot applied joint sealants æ
Part
zã Test method for the determination of the change in weight of fuel resistance joint sealants after fuel immersion Produits de scellement de joints appliqués à chaud æ Partie
z ã Méthode d 5essai pour la détermination de la variation de masse selon leur résistance aux hydrocarbures de produits de scellement de joints après immersion dans des hydrocarbures
Heiß verarbeitbare Fugenmassen æ Teil
zã Prüfverfahren zur Bestimmung der Gewichtsänderung nach Treibstofflagerung This European Standard was approved by CEN on
{ November
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u z z ræ zã t r s y ESIST EN 13880-8:2019



EN 13880-8:2018 (E) 2 Contents Page
European foreword . 3 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 5 4 Principle . 5 5 Apparatus . 5 6 Preparation and conditioning of test specimens . 6 7 Procedure. 6 8 Calculation and expression of results . 7 9 Precision . 7 10 Test report . 7
SIST EN 13880-8:2019



EN 13880-8:2018 (E) 3 European foreword This document (EN 13880-8:2018) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2019, and conflicting national standards shall be withdrawn at the latest by June 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This European Standard is one of a series of standards as listed below: EN 13880-1, Hot applied joint sealants — Part 1: Test method for the determination of density at 25 °C. EN 13880-2, Hot applied joint sealants — Part 2: Test method for the determination of cone penetration at 25 °C. EN 13880-3, Hot applied joint sealants — Part 3: Test method for the determination of penetration and recovery (resilience). EN 13880-4, Hot applied joint sealants — Part 4: Test method for the determination of heat resistance — Change in penetration value. EN 13880-5, Hot applied joint sealants — Part 5: Test method for the determination of flow resistance. EN 13880-6, Hot applied joint sealants — Part 6: Test method for the preparation of samples for testing. EN 13880-7, Hot applied joint sealants — Part 7: Function testing of joint sealants. EN 13880-8, Hot applied joint sealants — Part 8: Test method for the determination of the change in weight of fuel resistance joint sealants after fuel immersion. EN 13880-9, Hot applied joint sealants — Part 9: Test method for the determination of compatibility with asphalt pavements. EN 13880-10, Hot applied joint sealants — Part 10: Test method for the determination of adhesion and cohesion following continuous extension and compression. EN 13880-11, Hot applied sealants — Part 11: Test method for
...