oSIST prEN 12100:2024
(Main)Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports
Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports
This document specifies a test method for the resistance to bending of a test piece, made of a valve assembled together with two pipes and placed between supports, when subjected to internal pressure.
This document is applicable to valves with a polyethylene (PE) body for use with pipes having a nominal outside diameter from greater than 63 mm up to and including 400 mm and intended for the transport of fluids.
When specified in the product standard, this document can be applied to valves of material different than PE.
Kunststoff-Rohrleitungssysteme - Armaturen aus Polyethylen (PE) - Prüfverfahren für den Widerstand gegen Biegen bei Dreipunktbelastung
Dieses Dokument legt ein Prüfverfahren für die Biegefestigkeit eines Prüfkörpers fest, der aus einer mit zwei Rohren zusammengebauten Armatur besteht und zwischen Auflagern angeordnet ist, wenn er einem Innendruck ausgesetzt wird.
Dieses Dokument gilt für Armaturen mit einem Gehäuse aus Polyethylen (PE) für den Einsatz mit Rohren mit einem Nenn-Außendurchmesser größer als 63 mm bis einschließlich 400 mm, die für den Transport von Flüssigkeiten vorgesehen sind.
Wenn in der Produktnorm festgelegt, kann dieses Dokument auf Armaturen aus einem anderen Werkstoff als PE angewendet werden.
Systemes de canalisations en plastiques - Robinets en polyéthylene (PE) - Méthode d'essai de résistance a la flexion entre supports
Le présent document spécifie une méthode d'essai relative à la résistance à la flexion d’une éprouvette, constituée d’un robinet assemblé à deux tubes et placée entre des supports, lorsqu’elle est soumise à une pression interne.
Le présent document s'applique aux robinets avec un corps en polyéthylène (PE), utilisés avec des tubes présentant un diamètre extérieur nominal supérieur à 63 mm et inférieur ou égal à 400 mm, destinés au transport de fluides.
Lorsque cela est spécifié dans la norme de produit, le présent document peut être appliqué aux robinets en matériau autre que le PE.
Cevni sistemi iz polimernih materialov - Ventili iz polietilena (PE) - Metoda za preskus odpornosti proti upogibanju med podporami
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 12100:2024
01-januar-2024
Cevni sistemi iz polimernih materialov - Ventili iz polietilena (PE) - Metoda za
preskus odpornosti proti upogibanju med podporami
Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to
bending between supports
Kunststoff-Rohrleitungssysteme - Armaturen aus Polyethylen (PE) - Prüfverfahren für
den Widerstand gegen Biegen bei Dreipunktbelastung
Systemes de canalisations en plastiques - Robinets en polyéthylene (PE) - Méthode
d'essai de résistance a la flexion entre supports
Ta slovenski standard je istoveten z: prEN 12100
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
83.140.30 Polimerne cevi in fitingi za Plastics pipes and fittings for
snovi, ki niso tekočine non fluid use
oSIST prEN 12100:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 12100:2024
---------------------- Page: 2 ----------------------
oSIST prEN 12100:2024
DRAFT
EUROPEAN STANDARD
prEN 12100
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2023
ICS 23.040.01 Will supersede EN 12100:1997
English Version
Plastics piping systems - Polyethylene (PE) valves - Test
method for resistance to bending between supports
Systèmes de canalisations en plastiques - Robinets en Kunststoff-Rohrleitungssysteme - Armaturen aus
polyéthylène (PE) - Méthode d'essai de résistance à la Polyethylen (PE) - Prüfverfahren für den Widerstand
flexion entre supports gegen Biegen bei Dreipunktbelastung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12100:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 12100:2024
prEN 12100:2023 (E)
Contents Page
EUROPEAN FOREWORD . 3
INTRODUCTION. 4
1 SCOPE . 5
2 NORMATIVE REFERENCES . 5
3 TERMS AND DEFINITIONS . 5
4 PRINCIPLE . 5
5 APPARATUS . 6
5.1 STATIC UNIAXIAL TESTING MACHINE . 6
5.2 TORQUE MEASURING DEVICE .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.