SIST EN ISO 8100-2:2026
(Main)Lifts for the transport of persons and goods - Part 2: Design rules, calculations, examinations and tests of lift components (ISO 8100-2:2026)
- Abstract
This document specifies for passenger lifts and goods passenger lifts:
the verification of door locking devices;
the verification of safety gears;
the verification of overspeed governors;
the verification of buffers;
the verification of safety circuits and SIL-rated circuits;
the verification of ascending car overspeed protection means;
the verification of unintended car movement protection means;
the verification of rupture valves and one-way restrictors;
the verification of suspension and compensation means;
the discard criteria for suspension means and sheaves;
the calculation of guide rails;
the calculation of rams, cylinders, rigid pipes and fittings;
the evaluation of the traction;
the evaluation of the safety factor on suspension means;
the pendulum shock tests;
the fault exclusion for electric and electronic components;
the design rules for SIL-rated circuits.
This document is not applicable to passenger lifts, goods passenger lifts or lift components, which are installed or manufactured before the date of its publication.
- Status
- Published
- Public Enquiry End Date
- 30-Jan-2024
- Publication Date
- 11-Nov-2026
- Technical Committee
- DTN - Lift and transport appliances
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 24-Jun-2026
- Due Date
- 29-Aug-2026
- Completion Date
- 12-Nov-2026
SIST EN ISO 8100-2:2026 is a European Standard published by CEN for passenger lifts and goods passenger lifts. It specifies design rules, calculations, verifications and tests for lift components, including door locking devices, safety gears, overspeed governors, buffers, suspension means, hydraulic components and SIL-rated circuits. It is intended for lift designers, manufacturers, test bodies, assessors and other people who need to check that lift components are verified in a consistent way.
What does SIST EN ISO 8100-2:2026 specify?
SIST EN ISO 8100-2:2026 sets the technical methods used to verify and calculate key lift components for passenger lifts and goods passenger lifts. It also states that the document is not applicable to lifts or lift components installed or manufactured before its publication date.
The document is organized into Clauses 1 to 5, followed by Annexes A to E and Annex ZA. Clause 4 carries the main technical rules, calculations, verifications and tests, while Clause 5 points users to ISO/TS 8100-3 when that part is applicable.
| Annex | What it covers |
|---|---|
| Annex A | Normative requirements for SIL-rated circuits |
| Annex B | Informative example for guide rail calculation |
| Annex C | Informative example for traction calculation |
| Annex D | Informative examples for equivalent number of pulleys, Nequiv |
| Annex E | Informative relationship between ISO 8100-20 and EN ISO 8100-2 |
| Annex ZA | Informative relationship with Directive 2014/33/EU |
What are the key requirements of SIST EN ISO 8100-2:2026?
General design and test conditions
Clause 4.1 requires passenger lifts and goods passenger lifts to meet the safety requirements and protective measures in the following clauses, and to use ISO 12100:2010 for hazards that are relevant but not specifically covered. It also sets the required measurement accuracy for test instruments, which matters because the verification results depend on reliable readings.
In practice, this means the engineer or test lab must use suitable instruments for masses, forces, distances, speeds, acceleration, voltage, temperature, flow and pressure. If the measurement method is not accurate enough, the verification result is not a solid basis for approval or conformity assessment.
Component verifications and performance checks
Clause 4.2 covers landing and car door locking devices. It separates the verification into operation, mechanical tests, electrical tests and special tests for certain locking device types, including horizontally or vertically sliding doors with several panels and flap-type locking devices for hinged doors.
Clauses 4.3 to 4.5 cover safety gear, overspeed governors and buffers. SIST EN ISO 8100-2:2026 distinguishes instantaneous and progressive safety gear, requires test samples and test procedures, and includes calculations for permissible mass. For buffers, it treats energy dissipation buffers and energy accumulation buffers with non-linear characteristics separately, so the chosen device has to be checked in the way it actually works.
Clauses 4.6 to 4.9 cover safety circuits, SIL-rated circuits, ascending car overspeed protection means, unintended car movement protection means, and rupture valves/one-way restrictors. These clauses require documentation, test samples, mechanical and temperature tests, failure analysis, functional and safety tests, and specific statements about the intended duty and test conditions. In practice, this is the core evidence trail for safety-related controls and hydraulic protection parts.
Calculations, structural parts and mechanical tests
Clauses 4.10 to 4.15 cover the calculation of guide rails, traction, the safety factor of suspension means, the verification of suspension and compensation means, discard criteria for suspension means and power transmission contact, and the calculation of rams, cylinders, rigid pipes and fittings. The document also includes pendulum shock tests in Clause 4.16.
For design work, this matters because the standard does not rely on one generic calculation. It gives separate rules for bending, buckling, traction, rope and belt behaviour, pressure resistance and guidance-related checks, so the designer can size the component and then verify it with the matching test or calculation method.
Fault exclusion and SIL-rated circuits
Clause 4.17 allows fault exclusion for electric and electronic components only when the component is used within its worst-case limits and the exclusion is justified and documented. It also states that fault exclusion is not a way to bypass protection against electric shock.
Clause 4.18 sets the design rules for SIL-rated circuits. SIST EN ISO 8100-2:2026 allows compliance either with the relevant requirements in Annex A or with the relevant IEC 61508 requirements, subject to the stated restrictions. Clause 5 adds that ISO/TS 8100-3:2019, Clause 4, is to be followed when it applies.
What terms does SIST EN ISO 8100-2:2026 define?
- SIL-rated circuit (Src) - A safety-related circuit that is designed so that detection of a failure leads to a safe state.
- PFD - Probability of a dangerous failure on demand, used when the safety function is requested less than once a year.
- PFH - Probability of a dangerous failure per hour, used when the safety function is requested more than once a year.
- FMEDA - Failure mode effect and diagnostic analysis, the safety analysis method used to identify failure modes, diagnostics and failure rates.
- Fault exclusion - A documented judgement that a specific fault can be treated as not credible under defined conditions.
- Pendulum shock test - An impact test using hard or soft pendulum devices to check doors and car or wall elements.
Who uses SIST EN ISO 8100-2:2026?
Lift manufacturers, component suppliers, installers, test laboratories, certification bodies, regulators, quality managers and maintenance providers use SIST EN ISO 8100-2:2026. The standard is most useful when a team needs to design a component, run type tests, prepare technical documentation, assess safety-related electronics or check whether a component can be accepted for a lift project.
The document is also relevant to health and safety bodies, market surveillance teams and procurement staff. In practice, they use it to compare component claims against a common verification method and to specify what evidence must be available.
What changed in SIST EN ISO 8100-2:2026 from the previous edition?
SIST EN ISO 8100-2:2026 replaces ISO 8100-2:2019. The main changes stated for the new edition are:
- editorial revision of the document structure according to ISO/IEC Directives, Part 2
- updated mechanical tests and temperature tests for safety circuits and SIL-rated circuits
- corrected errors in the traction calculation formulae
- added verification methods for suspension and compensation means other than steel wire ropes
- added discard criteria for suspension means and power transmission contact
- revised requirements for SIL-rated circuits, previously called PESSRAL
Which standards are used with SIST EN ISO 8100-2:2026?
| Standard | What it contributes |
|---|---|
| ISO 8100-1:2023 | Base safety rules for lift construction and installation, and the terms used in this document |
| ISO 8100-33:2022 | T-type guide rails for lift cars and counterweights |
| ISO 3108:2017 | Test method for measured breaking force of steel wire ropes |
| ISO 4344:2022 | Minimum requirements for steel wire ropes for lifts |
| ISO 12100:2010 | General principles for risk assessment and risk reduction |
| ISO 29584:2015 | Pendulum impact testing reference |
| IEC 60068-2-6 / -14 / -27 | Vibration, temperature change and shock tests |
| IEC 60112:2020 | Proof and comparative tracking indices for insulating materials |
| IEC 60664-1:2020 | Insulation coordination for low-voltage equipment |
| IEC 60893-3-1:2012 | Insulating material specification for rigid laminated sheets |
| IEC 60947-4-1 / -5-1 | Contactors, motor-starters and control circuit devices |
| IEC 61508-2:2010 / -3:2010 | Functional safety requirements for hardware and software |
| IEC 61558-1:2017 | Safety requirements for power transformers and power supplies |
| IEC 61709:2017 | Reliability reference conditions and failure-rate conversion |
| EN 10025-2:2019 | Technical delivery conditions for non-alloy structural steels |
| EN 12385-1 and EN 12385-5 | Safety requirements for steel wire ropes and lift ropes |
| EN 13411-6 and EN 13411-7 | Safety requirements for asymmetric and symmetric wedge sockets |
| ISO/TS 8100-3:2019 | Additional requirements to use when applicable with this document |
| ISO 8100-20:2018 | Related global essential safety requirements, referenced in Annex E |
Annex A also refers to IEC 61784-3:2021 for safety-related data communication links, and the fault-exclusion notes refer to ISO 13849-2:2012 and IEC 61800-5-2 in the cited examples.
What does the SIST EN ISO 8100-2:2026 document contain?
The document contains calculation methods, test setups, verification steps and reporting points for a broad set of lift components. It includes procedures for door locking devices, safety gear, overspeed governors, buffers, hydraulic rupture protection, guide rails, traction, suspension means, rams, cylinders, rigid pipes, fittings and pendulum shock testing.
Annex A is the technical core for SIL-rated circuits and includes architecture guidance, diagnostic intervals, failure analysis methods and formulas for PFD, PFH and residual error rate. Annexes B, C and D provide worked examples for guide rails, traction and pulley equivalence, which help engineers apply the formulas without reproducing them from scratch. Annex ZA links the standard to EU lifts legislation.
Relations
- Effective Date
- 01-Jul-2026
- Effective Date
- 24-Jun-2026
- Effective Date
- 24-Jun-2026
- Effective Date
- 24-Jun-2026
- Effective Date
- 24-Jun-2026
- Effective Date
- 24-Jun-2026
- Effective Date
- 24-Jun-2026
- Effective Date
- 24-Jun-2026
- Effective Date
- 18-Jan-2023
- Effective Date
- 06-Jul-2022
Get Certified
Connect with accredited certification bodies for this standard

DIBt (Deutsches Institut für Bautechnik)
German Institute for Building Technology.
DIN CERTCO
DIN Group product certification.

Aboma Certification B.V.
Specialized in construction, metal, and transport sectors.
Sponsored listings
Frequently Asked Questions
SIST EN ISO 8100-2:2026 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Lifts for the transport of persons and goods - Part 2: Design rules, calculations, examinations and tests of lift components (ISO 8100-2:2026)". This standard covers: This document specifies for passenger lifts and goods passenger lifts: the verification of door locking devices; the verification of safety gears; the verification of overspeed governors; the verification of buffers; the verification of safety circuits and SIL-rated circuits; the verification of ascending car overspeed protection means; the verification of unintended car movement protection means; the verification of rupture valves and one-way restrictors; the verification of suspension and compensation means; the discard criteria for suspension means and sheaves; the calculation of guide rails; the calculation of rams, cylinders, rigid pipes and fittings; the evaluation of the traction; the evaluation of the safety factor on suspension means; the pendulum shock tests; the fault exclusion for electric and electronic components; the design rules for SIL-rated circuits. This document is not applicable to passenger lifts, goods passenger lifts or lift components, which are installed or manufactured before the date of its publication.
This document specifies for passenger lifts and goods passenger lifts: the verification of door locking devices; the verification of safety gears; the verification of overspeed governors; the verification of buffers; the verification of safety circuits and SIL-rated circuits; the verification of ascending car overspeed protection means; the verification of unintended car movement protection means; the verification of rupture valves and one-way restrictors; the verification of suspension and compensation means; the discard criteria for suspension means and sheaves; the calculation of guide rails; the calculation of rams, cylinders, rigid pipes and fittings; the evaluation of the traction; the evaluation of the safety factor on suspension means; the pendulum shock tests; the fault exclusion for electric and electronic components; the design rules for SIL-rated circuits. This document is not applicable to passenger lifts, goods passenger lifts or lift components, which are installed or manufactured before the date of its publication.
SIST EN ISO 8100-2:2026 is classified under the following ICS (International Classification for Standards) categories: 91.140.90 - Lifts. Escalators. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN ISO 8100-2:2026 has the following relationships with other standards: It is inter standard links to SIST EN 10025-2:2019, SIST EN 81-21:2009+A1:2012, SIST EN 12016:2005+A1:2008, SIST EN 13015:2002+A1:2008, SIST EN 81-58:2004, SIST EN 12015:2005, SIST EN 81-73:2005, SIST EN 50600-2-1:2021, SIST EN 81-50:2020, SIST EN 81-50:2020. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN ISO 8100-2:2026 is associated with the following European legislation: EU Directives/Regulations: 2014/33/EU; Standardization Mandates: M/549, M/599. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN ISO 8100-2:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2026
Dvigala za prevoz oseb in blaga - 2. del: Pravila konstruiranja, izračuni, pregledi in
preskusi sestavnih delov dvigal (ISO 8100-2:2026)
Lifts for the transport of persons and goods - Part 2: Design rules, calculations,
examinations and tests of lift components (ISO 8100-2:2026)
Aufzüge für den Personen- und Gütertransport - Teil 2: Konstruktionsregeln,
Berechnungen und Prüfungen von Aufzugskomponenten (ISO 8100-2:2026)
Elévateurs pour le transport de personnes et d'objets - Partie 2: Règles de conception,
calculs, examens et essais des composants pour élévateurs (ISO 8100-2:2026)
Ta slovenski standard je istoveten z: EN ISO 8100-2:2026
ICS:
91.140.90 Dvigala. Tekoče stopnice Lifts. Escalators
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 8100-2
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2026
EUROPÄISCHE NORM
ICS 91.140.90 Supersedes EN 81-50:2020
English Version
Lifts for the transport of persons and goods - Part 2:
Design rules, calculations, verifications and tests of lift
components (ISO 8100-2:2026)
Elévateurs pour le transport de personnes et d'objets - Aufzüge für den Personen- und Gütertransport - Teil 2:
Partie 2: Règles de conception, calculs, examens et Konstruktionsregeln, Berechnungen und Prüfungen
essais des composants pour élévateurs (ISO 8100- von Aufzugskomponenten (ISO 8100-2:2026)
2:2026)
This European Standard was approved by CEN on 1 March 2026.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8100-2:2026 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/33/EU aimed to be covered . 4
European foreword
This document (EN ISO 8100-2:2026) has been prepared by Technical Committee ISO/TC 178 "Lifts,
escalators and moving walks" in collaboration with Technical Committee CEN/TC 10 “Lifts, escalators
and moving walks” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2026, and conflicting national standards
shall be withdrawn at the latest by June 2029.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 81-50:2020.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 8100-2:2026 has been approved by CEN as EN ISO 8100-2:2026 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2014/33/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request C(2023)
1)
6588 final (‘M/599’) to provide one voluntary means of conforming to requirements of
Directive 2014/33/EU of the European Parliament and of the Council of 26 February 2014 as regards
lifts and safety components for lifts (OJ L 96, 29.3.2014).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1.1, Table ZA.1.2 and
Table ZA.1.3 confers, within the limits of the scope of this standard, a presumption of conformity with
the corresponding essential requirements of that Directive and associated EFTA regulations.
Table ZA.1.1 — Correspondence between this European Standard and Annex I of
Directive 2014/33/EU
The relevant essential
health and safety
Clause(s)/sub-clause(s) of this EN Remarks/Notes
requirements of Annex I to
Directive 2014/33/EU
1.1 See below Table ZA.1.2
6.1 4.2.3, 4.3.5, 4.4.3, 4.5.4, 4.6.4, 4.7.4,
4.8.4, 4.9.4
Table ZA.1.2 — Correspondence between this European Standard and Annex I of
Directive 2006/42/EC
The relevant essential
health and safety
Clause(s)/sub-clause(s) of this EN Remarks/Notes
requirements of Annex I to
Directive 2006/42/EC
1.1.2 (a) 4
1.1.2 (c) 4
1)
C(2023) 6588, COMMISSION IMPLEMENTING DECISION of 5.10.2023 on a standardisation request to the European
Committee for Standardization as regards lifts and safety components for lifts in support of Directive 2014/33/EU of the
European Parliament and of the Council
Table ZA.1.3 — Correspondence between this European Standard and Annex III of
Regulation (EU) 2023/1230
The relevant essential
health and safety
requirements of Annex III Clause(s)/sub-clause(s) of this EN Remarks/Notes
to Regulation
(EU) 2023/1230
1.1.2 (a) 4
1.1.2 (c) 4
WARNING 1 Presumption of conformity stays valid only as long as a reference to this European Standard is
maintained in the list published in the Official Journal of the European Union. Users of this standard should
consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2 Other Union legislation may be applicable to the product(s) falling within the scope of this standard.
International
Standard
ISO 8100-2
Second edition
Lifts for the transport of persons
2026-03
and goods —
Part 2:
Design rules, calculations,
verifications and tests of lift
components
Reference number
ISO 8100-2:2026(en) © ISO 2026
ISO 8100-2:2026(en)
© ISO 2026
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 8100-2:2026(en)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Design rules, calculations, verifications and tests . 2
4.1 General .2
4.2 Verification of landing and car door locking devices .3
4.2.1 Verifications and tests .3
4.2.2 Test particular to certain types of locking devices .5
4.2.3 Instructions .5
4.3 Verification of safety gear .5
4.3.1 General provisions .5
4.3.2 Instantaneous safety gear .6
4.3.3 Progressive safety gear .8
4.3.4 Additional verifications.10
4.3.5 Instructions .10
4.4 Verification of overspeed governors .10
4.4.1 General provisions .10
4.4.2 Check on the characteristics of the overspeed governor .10
4.4.3 Instructions .11
4.5 Verification of buffers . . 12
4.5.1 General provisions . 12
4.5.2 Samples subject to test. 12
4.5.3 Testing . 12
4.5.4 Instructions . 15
4.6 Verification of safety circuits and SIL-rated circuits .16
4.6.1 General provisions .16
4.6.2 Samples subject to test.16
4.6.3 Tests .17
4.6.4 Instructions .18
4.7 Verification of ascending car overspeed protection means .19
4.7.1 General provisions .19
4.7.2 Statement and test sample.19
4.7.3 Testing .19
4.7.4 Instructions . 20
4.8 Verification of unintended car movement protection means . 20
4.8.1 General provisions . 20
4.8.2 Statement and test sample.21
4.8.3 Testing .21
4.8.4 Instructions . 23
4.9 Verification of rupture valve/one-way restrictor . 23
4.9.1 General provisions . 23
4.9.2 Testing .24
4.9.3 Test procedure.24
4.9.4 Instructions .27
4.10 Guide rails calculation . 28
4.10.1 Range of calculation . 28
4.10.2 Bending . 28
4.10.3 Buckling . . 30
4.10.4 Combination of bending and compression/tension or buckling stresses .31
4.10.5 Flange bending .31
4.10.6 Deflections .32
4.11 Traction calculation . 33
iii
ISO 8100-2:2026(en)
4.11.1 General . 33
4.11.2 Evaluation of T and T . 34
1 2
4.11.3 Formulae for a general case (see Figure 6) . 35
4.12 Evaluation of safety factor of steel wire ropes . 38
4.12.1 General . 38
4.12.2 Equivalent number, N , of pulleys . 39
equiv
4.12.3 Safety factor . 40
4.13 Verification of suspension means, compensation means and their terminations .41
4.13.1 Material and construction verification .41
4.13.2 Verification of elastomeric coated traction sheave grooves .41
4.13.3 Terminations of suspension means .42
4.13.4 Minimum breaking force (MBF) . 44
4.13.5 Fatigue lifetime testing . . 44
4.13.6 Friction factor .45
4.13.7 Additional mechanical tests for elastomeric coated suspension means .52
4.13.8 Additional mechanical tests for CFRP elastomeric coated suspension means.52
4.13.9 Instructions . 53
4.14 Discard criteria for suspension means and sheaves . 54
4.14.1 General . 54
4.14.2 Steel wire ropes . 54
4.14.3 Elastomeric coated suspension means . 55
4.15 Calculations of rams, cylinders, rigid pipes and fittings . 56
4.15.1 Calculation against over pressure . 56
4.15.2 Calculations of the jacks against buckling . 60
4.16 Pendulum shock tests . 66
4.16.1 General . 66
4.16.2 Test rig .67
4.16.3 Tests .67
4.16.4 Assessment of the test results . 68
4.17 Electrical and electronic components — Fault exclusion .71
4.18 Design rules for SIL-rated circuits . 75
4.19 Verification of the tripping element . 75
4.19.1 General provisions . 75
4.19.2 Check of the characteristics of the tripping element . 75
4.19.3 Instructions .76
Annex A (normative) SIL-rated circuits.77
Annex B (informative) Example for calculation of guide rails .97
Annex C (informative) Calculation of traction — Example .106
Annex D (informative) Equivalent number of pulleys, N — Examples .108
equiv
Bibliography .110
iv
ISO 8100-2:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 178, Lifts, escalators and moving walks, in
collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC 10,
Lifts, escalators and moving walks, in accordance with the Agreement on technical cooperation between ISO
and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 8100-2:2019), which has been technically
revised.
The main changes are as follows:
— mechanical tests and temperature tests of safety circuits and SIL-rated circuits have been updated;
— errors in the formulae for traction calculation have been corrected;
— verification methods for suspension and compensation means other than steel wire ropes have been
added;
— discard criteria for suspension means and sheaves have been added;
— requirements for SIL-rated circuits (previously called PESSRAL) have been revised;
— the document structure has been revised as per the ISO/IEC Directives, Part 2.
ISO/TS 8100-3:2019 provides information on the differences between this document and local standards
(ASME A17.1/CSA B44 and JIS A 4307 1/JIS A 4307 2) not included in this document.
This document is intended to be used in conjunction with documents calling for the use of this document
(e.g. ISO 8100-1:2026).
A list of all parts in the ISO 8100 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
v
ISO 8100-2:2026(en)
Introduction
This document is a type-C standard as stated in ISO 12100:2010.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance, etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate in the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations and hazardous events are
covered are indicated in the scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or type-B
standards, the requirements of this type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this type-C
standard.
vi
International Standard ISO 8100-2:2026(en)
Lifts for the transport of persons and goods —
Part 2:
Design rules, calculations, verifications and tests of lift
components
1 Scope
This document specifies for passenger lifts and goods passenger lifts:
— the verification of door locking devices;
— the verification of safety gears;
— the verification of overspeed governors;
— the verification of buffers;
— the verification of safety circuits and SIL-rated circuits;
— the verification of ascending car overspeed protection means;
— the verification of unintended car movement protection means;
— the verification of rupture valves and one-way restrictors;
— the verification of suspension and compensation means;
— the discard criteria for suspension means and sheaves;
— the calculation of guide rails;
— the calculation of rams, cylinders, rigid pipes and fittings;
— the evaluation of the traction;
— the evaluation of the safety factor on suspension means;
— the pendulum shock tests;
— the fault exclusion for electric and electronic components;
— the design rules for SIL-rated circuits.
This document is not applicable to passenger lifts, goods passenger lifts or lift components, which are
installed or manufactured before the date of its publication.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 148-1:2016, Metallic materials — Charpy pendulum impact test — Part 1: Test method
ISO 8100-2:2026(en)
ISO 3108:2017, Steel wire ropes — Test method — Determination of measured breaking force
ISO 4344:2022, Steel wire ropes for lifts — Minimum requirements
ISO 7500-1:2018, Metallic materials — Calibration and verification of static uniaxial testing machines — Part 1:
Tension/compression testing machines — Calibration and verification of the force-measuring system
ISO 8100-1:2026, Lifts for the transport of persons and goods — Part 1: Safety rules for the construction and
installation of passenger and goods passenger lifts
ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 17638:2016, Non-destructive testing of welds — Magnetic particle testing
ISO 23277:2015, Non-destructive testing of welds — Penetrant testing — Acceptance levels
ISO 29584:2015, Glass in building — Pendulum impact testing and classification of safety glass
IEC 60068-2-6:2007, Environmental testing — Part 2-6: Tests — Test Fc: Vibration (sinusoidal)
IEC 60068-2-14:2023, Environmental testing — Part 2-14: Tests — Test N: Change of temperature
IEC 60068-2-27:2008, Environmental testing — Part 2-27: Tests — Test Ea and guidance: Shock
IEC 60947-5-1:2024, Low-voltage switchgear and control gear — Part 5-1: Control circuit devices and switching
elements — Electromechanical control circuit devices
IEC 61508-1:2010, Functional safety of electrical/electronic/programmable electronic safety-related systems —
Part 1: General requirements
IEC 61508-2:2010, Functional safety of electrical/electronic/programmable electronic safety-related systems —
Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems
IEC 61508-3:2010, Functional safety of electrical/electronic/programmable electronic safety-related systems —
Part 3: Software requirements
IEC 61709:2017, Electric components — Reliability — Reference conditions for failure rates and stress models
for conversion
EN 10025-2:2019, Hot rolled products of structural steels — Part 2: Technical delivery conditions for non-alloy
structural steels
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 12100:2010 and ISO 8100-1:2026
apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Design rules, calculations, verifications and tests
4.1 General
Passenger and goods passenger lifts shall be in accordance with the safety requirements and/or protective
measures of the following clauses. In addition, the passenger and goods passenger lifts shall be designed in
accordance with the principles of ISO 12100:2010 for hazards relevant but not significant that are not dealt
with by this document.
ISO 8100-2:2026(en)
The precision of the instruments shall allow measurements to be made within the following accuracy:
a) ±1 % for masses, forces, distances, speeds;
b) ±2 % for accelerations, retardations;
c) ±5 % for voltages, currents;
d) ±5 °C for temperatures;
e) ±2,5 % for flow rate;
f) ±1 % for pressure, p, below 200 kPa;
g) ±5 % for pressure, p, above 200 kPa.
Recording equipment shall be capable of detecting signals, which vary in time of 0,01 s.
4.2 Verification of landing and car door locking devices
4.2.1 Verifications and tests
4.2.1.1 Verification of operation
It shall be verified that the electric safety device is not activated unless the locking element is engaged as
specified by the standard calling for the use of this document (e.g. 7 mm as per ISO 8100-1:2026, 4.3.9.1.2).
4.2.1.2 Mechanical tests
4.2.1.2.1 General
The mechanical tests shall be performed in the following sequence:
a) endurance test as per 4.2.1.2.2;
b) static test as per 4.2.1.2.3;
c) dynamic test as per 4.2.1.2.4.
The static test and the dynamic test shall be carried out with the same test sample used in the endurance
test.
4.2.1.2.2 Endurance test
The locking device shall be submitted to 1 000 000 (±1 %) complete cycles; one cycle comprises one forward
and return movement over the full travel possible in both directions.
During the endurance test, the electrical safety device of the lock shall close a resistive circuit under the
rated voltage and at a current value double that of the rated current of the locking device.
If the locking device is provided with a mechanical checking device for the locking pin or the position of
the locking element, this mechanical checking device shall additionally be submitted to an endurance test
of 100 000 (±1 %) cycles with the counterpart (means allowing the positive operation of the means used to
prove the position of a locking element) not in place and the mechanical locking and the safety contact being
not made.
The driving of the device shall be at a rate of 60 (±10 %) cycles per minute.
The number of operations of the locking element and the mechanical checking device shall be recorded by
mechanical or electrical counters.
ISO 8100-2:2026(en)
4.2.1.2.3 Static test
The test shall be made consisting of the application of a force, applied at the level of the lock, increasing to
the value laid down in the standard calling for the use of this document [e.g. ISO 8100-1:2026, 4.3.9.1.6 a)]
between 30 s to 60 s. The force shall be applied for a period of 300 s.
4.2.1.2.4 Dynamic test
The test shall be made consisting of the shock laid down in the standard calling for the use of this document
[e.g. ISO 8100-1:2026, 4.3.9.1.6 b)] at the height of the locking device.
4.2.1.3 Criteria for the mechanical tests
After the endurance test (see 4.2.1.2.2), the static test (see 4.2.1.2.3) and the dynamic test (see 4.2.1.2.4),
carried out on the locking device, there shall not be:
— wear reducing the minimum engagement of the locking element(s) as specified in the standard calling
for the use of this document (e.g. ISO 8100-1:2026, 4.3.9.1.2); or
— permanent deformation; or
— breakage of parts of the locking device or of the mechanical linkage.
4.2.1.4 Electrical test
4.2.1.4.1 Endurance test of safety contacts
This test is included in the endurance test laid down in 4.2.1.2.2.
4.2.1.4.2 Test of ability to break circuit
4.2.1.4.2.1 This test shall be carried out after the endurance test to check the ability to break a live circuit.
This test shall be made in accordance with the procedure in IEC 60947-5-1:2024. The values of current and
rated voltage serving as a basis for the tests shall be those specified for the locking device.
The capacity to break circuit shall be verified for both AC and DC conditions.
The tests shall be carried out with the locking device in all assembly positions specified in the instructions
(see 4.2.3).
The sample tested shall be provided with covers and electric wiring.
4.2.1.4.2.2 Locking devices for AC current shall open and close an electric circuit under a voltage equal
to 110 % of the specified rated voltage of the safety contact 50 times at intervals of 5 s to 10 s. The contact
shall remain closed for at least 0,5 s.
The testing circuit shall comprise of an inductor and a resistor in series. Its power factor shall be 0,7 ± 0,05
and the test current shall be 11 times the specified rated current of the locking device.
4.2.1.4.2.3 Locking devices for DC current shall open and close an electric circuit under a voltage equal to
110 % of the specified rated voltage of the safety contact 20 times at intervals of 5 s to 10 s. The contact shall
remain closed for at least 0,5 s.
The testing circuit shall comprise of an inductor and a resistor in series, having values such that the current
reaches 95 % of the steady-state value of the test current in 300 ms.
The test current shall be 110 % of the specified rated current of the locking device.
4.2.1.4.2.4 The tests are considered satisfactory if the safety contact has the ability to break a live circuit.
ISO 8100-2:2026(en)
4.2.1.4.3 Verification of clearances and creepage distances
The clearances in air and creepage distances shall be in accordance with the requirements laid down in the
standards calling for the use of this document (e.g. ISO 8100-1:2026, 4.11.2.2.4).
4.2.1.4.4 Verification of the protection against direct contact
In case of access to hazardous voltage this verification shall be made taking into account the mounting
position, the orientation and the layout of the locking device (e.g. ISO 8100-1:2026, 4.10.1.2).
4.2.2 Test particular to certain types of locking devices
4.2.2.1 Locking device for horizontally or vertically sliding doors with several panels
Devices providing direct mechanical linkage between panels shall be included in the tests mentioned in
4.2.1.2.2.
4.2.2.2 Flap type locking device for hinged door
For the flap type locking device the following shall be verified:
— the specified minimum overlap-dimensions as required by the standard calling for this device [e.g.
ISO 8100-1:2026, 4.3.9.1.12 b) and 4.3.9.1.12 c)];
— the locking device cannot engage when the landing door is not fully in the closed position as required by
the standard calling for this device [e.g. ISO 8100-1:2026, 4.3.9.1.12 d)];
— the locking force limiter as in the standard calling for the use of this document
[e.g. ISO 8100-1:2026, 4.3.9.1.12 f)] shall be tested on an operationally constructed door by pushing open
the door panels with a steadily increasing force until the locking force limiter releases the flap. The force
shall be applied as required by the standard calling for this device [e.g. ISO 8100-1:2026, 4.3.9.1.12 f)].
The flap sh
...



