SIST EN ISO 11591:2021
(Main)Small craft - Field of vision from the steering position (ISO 11591:2020)
Small craft - Field of vision from the steering position (ISO 11591:2020)
This document specifies requirements for the field of vision from the steering position, forward
(horizontally and vertically) and astern, for small craft up to 24 m length of hull (LH) in accordance with
ISO 8666:2016.
Kleine Wasserfahrzeuge - Sichtfeld vom Steuerstand (ISO 11591:2020)
Dieses Dokument legt Anforderungen an das Sichtfeld vom Steuerstand aus nach vorn (horizontal und vertikal) und nach achtern bei kleinen Wasserfahrzeugen mit einer Rumpflänge (LH) bis 24 m nach ISO 8666 fest.
Petits navires - Champ de vision depuis le poste de pilotage (ISO 11591:2020)
Le présent document spécifie les exigences relatives au champ de vision depuis le poste de pilotage, vers l'avant (horizontalement et verticalement) et vers l'arrière, pour les petits navires d'une longueur de coque (LH) inférieure ou égale à 24 m conformément à l'ISO 8666:2016.
Mala plovila - Vidno polje izza krmila (ISO 11591:2020)
Ta dokument določa zahteve za vidno polje izza krmila, spredaj (vodoravno in navpično) in zadaj
za mala plovila z dolžino trupa (LH) do 24 m v skladu s
standardom ISO 8666:2016.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11591:2021
01-januar-2021
Nadomešča:
SIST EN ISO 11591:2019
Mala plovila - Vidno polje izza krmila (ISO 11591:2020)
Small craft - Field of vision from the steering position (ISO 11591:2020)
Kleine Wasserfahrzeuge - Sichtfeld vom Steuerstand (ISO 11591:2020)
Petits navires - Champ de vision depuis le poste de pilotage (ISO 11591:2020)
Ta slovenski standard je istoveten z: EN ISO 11591:2020
ICS:
47.080 Čolni Small craft
SIST EN ISO 11591:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11591:2021
---------------------- Page: 2 ----------------------
SIST EN ISO 11591:2021
EN ISO 11591
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2020
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 11591:2019
English Version
Small craft - Field of vision from the steering position (ISO
11591:2020)
Petits navires - Champ de vision depuis le poste de Kleine Wasserfahrzeuge - Sichtfeld vom Steuerstand
pilotage (ISO 11591:2020) (ISO 11591:2020)
This European Standard was approved by CEN on 13 September 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11591:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11591:2021
EN ISO 11591:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11591:2021
EN ISO 11591:2020 (E)
European foreword
This document (EN ISO 11591:2020) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with Technical Committee CEN/TC 464 “Small Craft” the secretariat of which is
held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2021, and conflicting national standards shall be
withdrawn at the latest by April 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11591:2019.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11591:2020 has been approved by CEN as EN ISO 11591:2020 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11591:2021
EN ISO 11591:2020 (E)
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request
M/542/C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1— Correspondence between this European Standard and Annex 1 and Annex II of
Directive 2013/53/EU
Essential Requirements of Clause(s)/sub-clause(s) of Remarks/Notes
Directive 2013/53/EU this EN
I.A.2.4 — Visibility from the main 1, 2, 3, 4, 5, 6, 7 This Standard specifies the field
steering position of vision requirements from the
main steering position, both
forward and astern, in the
horizontal and vertical planes for
recreational craft as defined in
Article 3(2) of Directive
2013/53/EU that fall within its
scope.
I.A.2.5 - Owner’s manual 8
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this
European Standard is maintained in the list published in the Official Journal of the European
Union. Users of this standard should consult frequently the latest list published in the Official
Journal of the European Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the
scope of this standard.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 11591:2021
INTERNATIONAL ISO
STANDARD 11591
Fourth edition
2020-10
Small craft — Field of vision from the
steering position
Petits navires — Champ de vision depuis le poste de pilotage
Reference number
ISO 11591:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 11591:2021
ISO 11591:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11591:2021
ISO 11591:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements for all craft . 2
4.1 General requirements . 2
4.2 Field of vision — Forward . 3
4.2.1 Horizontal . 3
4.2.2 Vertical . 3
4.3 Field of vision — Astern. 3
5 Additional requirements for human-powered craft . 4
5.1 General requirements . 4
6 Additional requirements for power-driven craft with steering wheel or equivalent
fixed installed direction control . 4
6.1 General requirements . 4
7 Additional requirements for sailing craft under sail or auxiliary power .4
7.1 General requirements . 4
7.2 Sails . 4
7.3 Steering means . 4
8 Owner’s manual. 6
8.1 Human-powered craft . 6
8.2 Power-driven craft . 6
8.3 Sailing craft . 7
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11591:2021
ISO 11591:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction an
...
SLOVENSKI STANDARD
oSIST prEN ISO 11591:2020
01-julij-2020
Mala plovila - Vidno polje izza krmila (ISO/FDIS 11591:2020)
Small craft - Field of vision from the steering position (ISO/FDIS 11591:2020)
Kleine Wasserfahrzeuge - Sichtfeld vom Steuerstand (ISO/FDIS 11591:2020)
Petits navires - Champ de vision depuis le poste de pilotage (ISO/FDIS 11591:2020)
Ta slovenski standard je istoveten z: prEN ISO 11591
ICS:
47.080 Čolni Small craft
oSIST prEN ISO 11591:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 11591:2020
---------------------- Page: 2 ----------------------
oSIST prEN ISO 11591:2020
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 11591
ISO/TC 188
Small craft — Field of vision from the
Secretariat: SIS
steering position
Voting begins on:
20200520
Petits navires — Champ de vision depuis le poste de pilotage
Voting terminates on:
20200812
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 11591:2020(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2020
---------------------- Page: 3 ----------------------
oSIST prEN ISO 11591:2020
ISO/FDIS 11591:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 11591:2020
ISO/FDIS 11591:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements for all craft . 2
4.1 General requirements . 2
4.2 Field of vision — Forward . 3
4.2.1 Horizontal . 3
4.2.2 Vertical . 3
4.3 Field of vision — Astern. 3
5 Additional requirements for human-powered craft . 4
5.1 General requirements . 4
6 Additional requirements for power-driven craft with steering wheel or equivalent
fixed installed direction control . 4
6.1 General requirements . 4
7 Additional requirements for sailing craft under sail or auxiliary power .4
7.1 General requirements . 4
7.2 Sails . 4
7.3 Steering means . 4
8 Owner’s manual. 6
8.1 Humanpowered craft . 6
8.2 Powerdriven craft . 6
8.3 Sailing craft . 7
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 8
© ISO 2020 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 11591:2020
ISO/FDIS 11591:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and nongovernmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of Standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 188, Small craft.
This fourth edition cancels and replaces the third edition (ISO 11591:2019), of which it constitutes a
minor revision. The changes compared to the previous edition are as follows:
— all normative references have been dated.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 11591:2020
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 11591:2020(E)
Small craft — Field of vision from the steering position
1 Scope
This document specifies requirements for the field of vision from the steering position, forward
(horizontally and vertically) and astern, for small craft up to 24 m length of hull (L ) in accordance with
H
ISO 8666:2016.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 7010:2019, Graphical symbols — Safety colours and safety signs — Registered safety signs
ISO 8666:2016, Small craft — Principal data
ISO 10240:2019, Small craft — Owner's manual
ISO 11192:2005, Small craft — Graphical symbols
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
steering position
steering area (3.2) or steering location (3.3)
3.2
steering area
area on board a sailing craft (3.11) from which the operator (3.14) steers the craft
3.3
steering location
location on board a power-driven craft (3.12) or a human-powered craft (3.10) in which the operator
(3.14) steers the craft and controls the propulsion
3.4
main steering position
steering position (3.1) as defined by the manufacturer and specified in the owner’s manual that meets
the field of vision requirements of this document
3.5
high eye position
eye position 1 730 mm above the surface on which the operator (3.14) stands,
400 mm from the centre of the steering wheel rim
© ISO 2020 – All rights reserved 1
---------------------- Page: 7 ----------------------
oSIST prEN ISO 11591:2020
ISO/FDIS 11591:2020(E)
3.6
high eye position
eye position 840 mm above the intersection of the compr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.