SIST EN IEC 60966-2-1:2024

SLOVENSKI STANDARD
01-junij-2024
Sestavi radiofrekvenčnih in koaksialnih kablov - 2-1. del: Področna specifikacija za
sestave zvijavih koaksialnih kablov
Radio frequency and coaxial cable assemblies - Part 2-1: Sectional specification for
flexible coaxial cable assemblies
Konfektionierte Koaxial- und Hochfrequenzkabel - Teil 2-1: Rahmenspezifikation für
flexible konfektionierte Koaxialkabel
Cordons coaxiaux et cordons pour fréquences radioélectriques – Partie 2-1:
Spécification intermédiaire pour cordons coaxiaux souples
Ta slovenski standard je istoveten z: EN IEC 60966-2-1:2024
ICS:
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60966-2-1

NORME EUROPÉENNE
EUROPÄISCHE NORM May 2024
ICS 33.120.10 Supersedes EN 60966-2-1:2009
English Version
Radio frequency and coaxial cable assemblies - Part 2-1:
Sectional specification for flexible coaxial cable assemblies
(IEC 60966-2-1:2024)
Cordons coaxiaux et cordons pour fréquences Konfektionierte Koaxial- und Hochfrequenzkabel - Teil 2-1:
radioélectriques - Partie 2-1: Spécification intermédiaire Rahmenspezifikation für flexible konfektionierte
pour cordons coaxiaux souples Koaxialkabel
(IEC 60966-2-1:2024) (IEC 60966-2-1:2024)
This European Standard was approved by CENELEC on 2024-04-23. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60966-2-1:2024 E

European foreword
The text of document 46/966/FDIS, future edition 4 of IEC 60966-2-1, prepared by IEC/TC 46 "Cables,
wires, waveguides, RF connectors, RF and microwave passive components and accessories" was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 60966-2-1:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-01-23
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-04-23
document have to be withdrawn
This document supersedes EN 60966-2-1:2009 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60966-2-1:2024 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60966-1 2019 Radio frequency and coaxial cable EN IEC 60966-1 2019
assemblies - Part 1: Generic specification -
General requirements and test methods
IEC 61169 series Radio frequency connectors EN 61169 series
IEC 61196-1-126 - Coaxial communication cables - Part 1- - -
126: Electrical test methods - Corona
extinction voltage
IEC 61196-9 - Coaxial communication cables - Part 9: - -
Sectional specification for flexible RF
coaxial cables
IEC 60966-2-1 ®
Edition 4.0 2024-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Radio frequency and coaxial cable assemblies –

Part 2-1: Sectional specification for flexible coaxial cable assemblies

Cordons coaxiaux et cordons pour fréquences radioélectriques –

Partie 2-1: Spécification intermédiaire pour cordons coaxiaux souples

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.10  ISBN 978-2-8322-8412-4

– 2 – IEC 60966-2-1:2024 © IEC 2024
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Design and construction . 7
4.1 Cable design and construction . 7
4.2 Connector design and construction . 7
4.3 The relative position dimensions of the interface . 7
4.4 Outline of the cable assembly . 7
5 Workmanship, marking and packaging . 8
6 IEC type designation . 9
7 Standard rating and characteristics . 10
7.1 Nominal characteristic impedance . 10
7.2 Temperature range . 10
7.3 Bending radius . 10
7.3.1 Static bending radius . 10
7.3.2 Dynamic bending radius . 10
7.4 Rated operating frequency range . 10
7.5 Rated working voltage . 10
7.6 Rated power . 11
8 Requirements of finished cable assemblies . 11
8.1 General . 11
8.2 Electrical requirements . 11
8.3 Mechanical requirements . 13
8.4 Environmental requirements . 15
9 Quality management . 17
10 Test schedules . 17
10.1 Qualification test . 17
10.2 Acceptance tests . 18
10.3 Periodic tests . 19
Annex A (normative) The relative position dimensions of the interface of some typical
connectors . 21
Annex B (normative) Shaking test method . 24
B.1 Purpose . 24
B.2 Test equipment . 24
B.3 Test procedure . 24
B.4 Requirements . 25
B.5 Test report . 25
Annex C (normative) Preferred arrangement for vibrations, shocks test . 26

Figure 1 – Length definition of cable assemblies with two connectors . 8
Figure 2 – Length definition of cable assemblies with one connector . 8
Figure 3 – The marking example of a cable assembly . 9
Figure A.1 – The relative position dimensions of the interface of some typical
connectors . 22

IEC 60966-2-1:2024 © IEC 2024 – 3 –
Figure B.1 – Schematic diagram of shaking test . 24
Figure C.1 – Preferred arrangement for vibrations, shocks test . 26

Table 1 – Rated temperature of cable assemblies with flexible cables . 10
Table 2 – Electrical requirements . 11
Table 3 – Mechanical requirements. 13
Table 4 – Environmental requirements . 15
Table 5 – Qualification test . 17
Table 6 – Acceptance test . 18
Table 7 – Sampling plan . 19
Table 8 – Periodic test . 19
Table A.1 – The dimensions of A and B in Figure A.1 . 23

– 4 – IEC 60966-2-1:2024 © IEC 2024
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO FREQUENCY AND COAXIAL CABLE ASSEMBLIES –

Part 2-1: Sectional specification for flexible coaxial cable assemblies

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-govern
...