iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 60669-2-1:2005/A12:2010

(Amendment)

Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic switches

Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic switches

This standard applies to electronic switches and to associated electronic extension units for household and similar fixed electrical installations either indoors or outdoors. It applies to electronic switches for a.c. only, for the operation of lamp circuits and the control of the brightness of lamps (dimmers) as well as the control of the speed of motors (for example, those used in ventilating fans) and for other purposes (for example, heating controls), with a rated voltage not exceeding 250 V and a rated current not exceeding 16 A. The operation and control as mentioned above are performed by a person via an actuating member, a sensing surface or a sensing unit, by means of touch, proximity, turn, optical, acoustic, thermal or any other influence. This standard also applies to electronic switches where the operation or control is made by physical means, for example, light, wind velocity, presence of persons, etc. This standard also applies to boxes for electronic switches, with the exception of mounting boxes for flush-type electronic switches. Electronic switches complying with this standard are suitable for use at ambient temperature not normally exceeding 25 °C but occasionally reaching 35 °C. In locations where special conditions prevail, such as in ships, vehicles and the like and in hazardous locations, for example, where explosions are liable to occur, special constructions may be required. NOTE 1 This standard is not intended to cover devices which are designed to be incorporated in appliances or are intended to be delivered together with a specific appliance and which are within the scope of IEC 60730 or IEC 61058-1. Examples of designs of electronic switches and functions are shown in annex AA. NOTE 2 Electronic switches without a mechanical switch in the main circuit do not provide a “full off-state”. Therefore, the circuit on the load side should be considered to be live.

Schalter für Haushalt und ähnliche ortsfeste elektrische Installationen - Teil 2-1: Besondere Anforderungen - Elektronische Schalter

Interrupteurs pour installations électriques fixes domestiques et analogues - Partie 2-1: Prescriptions particulières - Interrupteurs électroniques

Stikala za gospodinjstva in podobne nepremične električne inštalacije - 2-1. del: Posebne zahteve - Elektronska stikala

Ta standard velja za električna stikala in z njimi povezane električne priključne enote za gospodinjstva ter podobne nepremične električne inštalacije, bodisi v zaprtih prostorih bodisi zunaj.  Velja za elektronska stikala za zgolj enosmerni tok, za delovanje vezij žarnic, za nadzor nad svetlostjo žarnic (naprave za regulacijo svetlobe) ter tudi za nadzor hitrosti motorjev (na primer tistih, ki se uporabljajo pri ventilatorjih) ter v druge namene (na primer komande za ogrevanje), z ocenjeno napetostjo, ki ne presega 250 V, in ocenjenim tokom, ki ne presega 16 A. Delovanje in nadzor, kot sta omenjena zgoraj, oseba izvaja preko dela za aktiviranje, površine ali enote za zaznavanje, z dotikom, z bližino, z obratom, vidno, slušno, toplotno ali z katerim koli drugim vplivom. Ta standard prav tako velja za elektronska stikala, pri katerih se delovanje ali nadzor izvaja s fizičnimi sredstvi, na primer s svetlobo, s hitrostjo vetra, s prisotnostjo oseb itd. Ta standard velja tudi za doze za elektronska stikala, z izjemo vgradnih doz za elektronska stikala vgrezne vrste. Elektronska stikala, ki so v skladu s tem standardom, so primerna za uporabo pri temperaturi okolja, ki običajno ne presega 25°C, vendar občasno doseže 35°C. Na lokacijah, kjer prevladujejo posebni pogoji, kot na ladjah, v vozilih in podobno ter na nevarnih lokacijah, na primer kjer je možnost eksplozij, se lahko zahtevajo posebne konstrukcije. OPOMBA 1: Ta standard ni namenjen temu, da bi zajel naprave, ki so načrtovane za vgradnjo v aparate ali ki so namenjene temu, da se dostavijo skupaj z določenim aparatom in ki so znotraj področja uporabe IEC 60730 ali IEC 61058-1. Primeri načrtov elektronskih stikal in funkcij so prikazani v Dodatku AA. OPOMBA 2: Elektronska stikala brez mehanskega stikala v glavnem omrežju ne zagotavljajo »popolnega izklopa«. Potemtakem se mora omrežje na napajalni strani šteti za električno nabitega.

General Information

Status
Published
Publication Date
10-Oct-2010
ICS
29.120.40 - Switches
Technical Committee
EPR - Electrical accessories
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
23-Sep-2010
Due Date
28-Nov-2010
Completion Date
11-Oct-2010
Directive
2004/108/EU - DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
2014/30/EU - Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility (recast)
2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
Ref Project
EN 60669-2-1:2004/A12:2010 - Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic switches

Relations

Replaced By
SIST EN IEC 60669-2-1:2023 - Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic control devices (IEC 60669-2-1:2021)
Effective Date
20-Sep-2022
Amends
SIST EN 60669-2-1:2005 - Switches for household and similar fixed electrical installations -- Part 2-1: Particular requirements - Electronic switches
Effective Date
28-Jan-2023
Amends
SIST EN 60669-2-1:2005 - Switches for household and similar fixed electrical installations -- Part 2-1: Particular requirements - Electronic switches
Effective Date
01-Nov-2010

Buy Standard

EN 60669-2-1:2005/A12:2010EN 60669-2-1:2005/A12:2010
PreviousNext
Amendment
EN 60669-2-1:2005/A12:2010
English language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60669-2-1:2005/A12:2010
01-november-2010
6WLNDOD]DJRVSRGLQMVWYDLQSRGREQHQHSUHPLþQHHOHNWULþQHLQãWDODFLMHGHO
3RVHEQH]DKWHYH(OHNWURQVNDVWLNDOD
Switches for household and similar fixed electrical installations - Part 2-1: Particular
requirements - Electronic switches
Schalter für Haushalt und ähnliche ortsfeste elektrische Installationen - Teil 2-1:
Besondere Anforderungen - Elektronische Schalter
Interrupteurs pour installations électriques fixes domestiques et analogues - Partie 2-1:
Prescriptions particulières - Interrupteurs électroniques
Ta slovenski standard je istoveten z: EN 60669-2-1:2004/A12:2010
ICS:
29.120.40 Stikala Switches
SIST EN 60669-2-1:2005/A12:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60669-2-1:2005/A12:2010

---------------------- Page: 2 ----------------------

SIST EN 60669-2-1:2005/A12:2010

EUROPEAN STANDARD
EN 60669-2-1/A12

NORME EUROPÉENNE
June 2010
EUROPÄISCHE NORM

ICS 29.120.40


English version


Switches for household and similar fixed electrical installations -
Part 2-1: Particular requirements -
Electronic switches



Interrupteurs pour installations électriques Schalter für Haushalt und ähnliche
fixes domestiques et analogues - ortsfeste elektrische Installationen -
Partie 2-1: Prescriptions particulières - Teil 2-1: Besondere Anforderungen -
Interrupteurs électroniques Elektronische Schalter




This amendment A12 modifies the European Standard EN 60669-2-1:2004; it was approved by CENELEC on
2010-06-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 60669-2-1:2023(Main)
Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic control devices (IEC 60669-2-1:2021)
EN IEC 60669-2-1:2022

This clause of Part 1 is completely replaced by the following:
This part of IEC 60669 applies to electronic control devices, a general term to cover electronic switches, home and building electronic systems (HBES) / building automation and control systems (BACS) switches and electronic extension units.
It applies to electronic switches and to HBES/BACS switches, for alternating current (AC) only with a rated switching voltage not exceeding 250 V and a rated current not exceeding 16 A, intended for household and similar fixed electrical installations, either indoors or outdoors.
It also applies to electronic extension units with a rated supply voltage not exceeding 250 V AC and 120 V DC, such as sensors and push buttons.
This document also applies to electronic remote control switches (RCS) and electronic time delay switches (TDS). Particular requirements are given in Annex FF.
Switches including only passive components such as resistors, capacitors, inductors, positive temperature coefficient (PTC) and negative temperature coefficient (NTC) components, varistors, printed wiring boards and connectors are not considered as electronic control devices.
This document also applies to electronic switches and HBES/BACS switches for the operation of lighting equipment circuits and the control of the brightness of lighting equipment (dimmers) as well as the control of the speed of motors (for example, those used in ventilating fans) and for other purposes (for example, heating controls).
The operation and/or control as mentioned above can be transmitted by an electronic signal via several media, for example, powerline (mains), twisted pair, optical fibre, radio frequency, infrared, etc. and are performed:
- intentionally by a person via an actuating member, a key, a card, etc., via a sensing
surface or a sensing unit, by means of touch, proximity, turn, optical, acoustic, thermal;
- by physical means, for example, light, temperature, humidity, time, wind velocity, presence
of people;
- by any other influence.
This document also applies to electronic control devices which include integrated radio receivers and transmitters.
This document covers only those requirements for mounting boxes which are necessary for the tests on the electronic control devices.
Requirements for general purpose mounting boxes are given in the relevant part, if any, of IEC 60670.
This document is not intended to cover devices falling within the scope of IEC 60730 (all parts).
Electronic control devices complying with this document are suitable for use at ambient temperature not normally exceeding 25 °C but occasionally reaching 35 °C with a lower limit of the ambient air temperature of −5 °C.
NOTE 1 For lower temperatures, see Annex E.
Functional safety aspects are not covered by this document. Functional safety requirements are covered by the standards of the controlled devices.
In locations where special conditions prevail, such as in ships, vehicles and the like and in hazardous locations, for example where explosions are liable to occur, special construction and/or additional requirements may be required.
This document is not intended to cover devices which are designed to be incorporated in appliances or are intended to be delivered together with a specific appliance and which are within the scope of IEC 60730 (all parts) or IEC 61058-1.
Examples of designs of electronic switches and HBES/BACS switches and functions are shown in Annex AA.
Additional requirements for electronic control devices using DLT-technology in accordance with IEC 62756-1 are given in Annex CC.
Electrical interface specification for phase-cut dimmer used in phase-cut dimmed lighting systems are given for information only in Annex EE.
NOTE 2 Electronic switches and HBES/BACS switches without a mechanical switch in the main circuit do not provide a "full off-state". Therefore, the circuit on the load side are to be considered to be live.

  • Standard
    139 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    120 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60669-2-1:2023/A11:2023(Amendment)
Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic control devices
EN IEC 60669-2-1:2022/A11:2022

To give requirements and tests for electronic control devices, a general term to cover electronic switches, HBES/BACS switches and electronic extension units.
It applies to electronic switches and to HBES/BACS switches, for alternating current (AC) only with a rated switching voltage not exceeding 250 V and a rated current not exceeding 16 A, intended for household and similar fixed electrical installations, either indoors or outdoors.
It also applies to electronic extension units with a rated supply voltage not exceeding 250 V AC and 120 V DC.
This Part of IEC 60669 also applies to electronic control devices which include integrated radio receivers and transmitters.

  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61058-2-1:2021(Main)
Switches for appliances - Part 2-1: Particular requirements for cord switches (IEC 61058-2-1:2018)
EN IEC 61058-2-1:2021

This document applies to cord switches (mechanical or electronic) for appliances actuated by
hand, by foot or by other human activity, to operate or control electrical appliances and other
equipment for household or similar purposes with a rated voltage not exceeding 250 V and a
rated current not exceeding 16 A.
Throughout this document, the word "appliance" means "appliance or equipment".
These switches are intended to be operated by a person, via an actuating member or by
actuating a sensing unit. The actuating member or sensing unit can be integral or arranged
separately from the switch. The transmission of a signal between the actuating member or
sensing unit and the switch can be made either physically or electrically (for example,
electrical, optical, acoustic or thermal).
Switches which incorporate additional control functions governed by the switch function are
within the scope of this document.
This document also covers the indirect actuation of the switch when the operation of the
actuating member or sensing unit is provided by a remote control or a part of an appliance
such as a door.
NOTE 1 Electronic switches can be combined with mechanical switches giving full disconnection or
microdisconnection.
NOTE 2 Electronic switches without a mechanical switch in the supply circuit provide only electronic
disconnection. Therefore, the circuit on the load side is always considered to be live.
NOTE 3 For switches used in tropical climates, additional requirements can apply.
NOTE 4 Attention is drawn to the fact that the standards for appliances can contain additional or alternative
requirements for switches.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61058-2-5:2021(Main)
Switches for appliances - Part 2-5: Particular requirements for change-over selectors (IEC 61058-2-5:2018)
EN IEC 61058-2-5:2021

This Part of IEC 61058 applies to change-over selectors (mechanical or electronic) for
appliances actuated by hand, by foot or by other human activity, to operate or control
electrical appliances and other equipment for household or similar purposes with a rated
voltage not exceeding 480 V and a rated current not exceeding 63 A.
These change-over selectors are intended to be operated by a person, via an actuating
member or by actuating a sensing unit. The actuating member or sensing unit can be integral
with or arranged separately, either physically or electrically, from the switch, and can involve
transmission of a signal, for example electrical, optical, acoustic or thermal, between the
actuating member or sensing unit and the switch.
Change-over selectors which incorporate additional control functions governed by the switch
function are within the scope of this document.
This document also covers the indirect actuation of the switch when the operation of the
actuating member or sensing unit is provided by a remote control or a part of an appliance or
equipment such as a door.
NOTE 1 Electronic change-over selectors can be combined with mechanical change-over selectors giving full
disconnection or micro-disconnection.
NOTE 2 Electronic change-over selectors without a mechanical switch in the supply circuit provide only electronic
disconnection. Therefore, the circuit on the load side is always considered to be live.
NOTE 3 For change-over selectors used in tropical climates, additional requirements can apply.
NOTE 4 Attention is drawn to the fact that the standards for appliances can contain additional or alternative
requirements for change-over selectors.
NOTE 5 Throughout this document, the word "appliance" means "appliance or equipment".
This document applies to change-over selectors intended to be incorporated in, on, or with an
appliance.
This document also applies to change-over selectors incorporating electronic devices.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61058-2-4:2021(Main)
Switches for appliances - Part 2-4: Particular requirements for independently mounted switches (IEC 61058-2-4:2018)
EN IEC 61058-2-4:2021

This document applies to independently mounted switches for appliances (mechanical or
electronic) actuated by hand, by foot or by other human activity, to operate or control
electrical appliances and other equipment for household or similar purposes with a rated
voltage not exceeding 480 V and a rated current not exceeding 63 A.
These switches are intended to be operated by a person, via an actuating member or by
actuating a sensing unit. The actuating member or sensing unit can be integral with or
arranged separately, either physically or electrically, from the switch and involve transmission
of a signal, for example, electrical, optical, acoustic or thermal, between the actuating
member or sensing unit and the switch.
Switches which incorporate additional control functions governed by the switch function are
within the scope of this document.
This document also covers the indirect actuation of the switch when the operation of the
actuating member or sensing unit is provided by a remote control or by a part of an appliance
or equipment, such as a door.
NOTE 1 Electronic switches can be combined with mechanical switches giving full disconnection or microdisconnection.
NOTE 2 Electronic switches without a mechanical switch in the supply circuit provide only electronic
disconnection. Therefore, the circuit on the load side is always considered to be live.
NOTE 3 For switches used in tropical climates, additional requirements can apply.
NOTE 4 Attention is drawn to the fact that the standards for appliances can contain additional or alternative
requirements for switches.
NOTE 5 Throughout this document, the word "appliance" means "appliance or equipment".

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 63180:2021(Main)
Methods of measurement and declaration of the detection range of detectors - Passive infrared detectors for major and minor motion detection (IEC 63180:2020)
EN IEC 63180:2020

This document provides a methodology and test procedures to be able to declare and verify
the detection area for motion detectors using passive infrared technology in electronic control
devices and appliance switches, whether stand-alone (direct control of one or more
applications) or as part of home and building electronic systems or building automation
control systems (HBES/BACS) or similar.
It also provides a uniform way to present the test results.
The purpose of these detectors is to detect the major and minor movements of persons.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60669-1:2018/AC:2020(Corrigendum)
Switches for household and similar fixed electrical installations - Part 1: General requirements (IEC 60669-1:2017/COR1:2020)
EN 60669-1:2018/AC:2020-02

TAN - // IEC Corrigendum

  • Corrigendum
    6 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60934:2019(Main)
Circuit-breakers for equipment (CBE) (IEC 60934:2019)
EN IEC 60934:2019

This document is applicable to mechanical switching devices designed as "circuit-breakers for equipment" (CBE) for household and similar applications. CBEs according to this document are intended to provide protection to circuits within electrical equipment including its components (e.g. motors, transformers, internal wiring). This document covers also CBEs applicable for protection of electrical equipment in case of undervoltage and/or overvoltage. This document also covers CBEs which are suitable for isolation. CBEs are not applicable for overcurrent protection of wiring installations of buildings. CBEs according to this document have: - a rated voltage not exceeding 440 V AC (between phases) and/or DC not exceeding 250 V; - a rated current not exceeding 125 A; - a short-circuit capacity (Icn) of at least 6 × In (AC types) and 4 × In (DC types) but not exceeding 3 000 A. CBEs may have a conditional short-circuit current (Inc) rating in association with a specified short-circuit protective device (SCPD). A guide for coordination of a CBE associated in the same circuit with a SCPD is given in Annex F. For CBEs having a degree of protection higher than IP20 according to IEC 60529, for use in locations where hazardous environmental conditions prevail (e.g. excessive humidity, heat or cold or deposition of dust) and in hazardous locations (e.g. where explosions are liable to occur), special constructions may be required. This document contains all the requirements necessary to ensure compliance with the operational characteristics required for these devices by type tests. It also contains the details relative to test requirements and methods of testing necessary to ensure reproducibility of test results. This document states: a) the characteristics of CBEs; b) the conditions with which CBEs shall comply, with reference to: 1) their operation and behaviour in normal service; 2) their operation and behaviour in case of overload; 3) their operation and behaviour in case of short-circuits up to their rated short-circuit capacity; 4) their dielectric properties; c) the tests intended for confirming that these conditions have been met and the methods to be adopted for the tests; d) the data to be marked on the devices; e) the test sequences to be carried out and the number of samples to be submitted for certification purposes (see Annex C); f) the routine tests to be carried out to reveal unacceptable variations in material or manufacture, likely to affect safety (see Annex I).

  • Standard
    122 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61058-1-2:2017/AC:2019(Corrigendum)
Switches for appliances - Part 1-2: Requirements for electronic switches
EN 61058-1-2:2016/AC:2019-02
  • Corrigendum
    1 page
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61058-1-1:2017/AC:2019(Corrigendum)
Switches for appliances - Part 1-1: Requirements for mechanical switches
EN 61058-1-1:2016/AC:2019-02
  • Corrigendum
    1 page
    English language
    sale 10% off
    e-Library read for
    1 day