SIST EN 12261:2018
(Main)Gas meters - Turbine gas meters
Gas meters - Turbine gas meters
This document specifies the measuring conditions, requirements and tests for the construction,
performance and safety of class 1,0 axial and radial turbine gas meters with mechanical indicating
devices, herein after referred to as a meter(s), having in-line pipe connections for gas flow
measurement.
This document applies to turbine gas meters used to measure the volume of fuel gases of the 1st
and 2nd gas families, the composition of which is specified in EN 437, at maximum working
pressures up to 420 bar, actual flow rates up to 25 000 m3/h over a gas temperature range of at
least 40 K and for a climatic environmental temperature range of at least 50 K.
This document applies to meters that are installed in locations with vibration and shocks of low
significance and in
— closed locations (indoor or outdoor with protection as specified by the manufacturer) with
condensing or with non-condensing humidity
or, if specified by the manufacturer,
— open locations (outdoor without any covering) with condensing humidity or with noncondensing
humidity
and in locations with electromagnetic disturbances.
Unless otherwise specified in this document:
— all pressures used are gauge;
— all influence quantities, except the one under test, are kept relatively constant at their
reference value.
Gaszähler - Turbinenradgaszähler
Dieses Dokument beschreibt die Messbedingungen, Anforderungen und Prüfungen hinsichtlich Konstruktion, Leistung und Sicherheit von axialen und radialen Klasse-1,0-Turbinenradgaszählern mit mechanischen Anzeigegeräten (im Folgenden „Zähler“ genannt) mit in der Hauptleitung liegenden Anschlüssen zur Durchflussmessung.
Dieses Dokument gilt für Turbinenradgaszähler, die zur Volumenmessung von Brenngasen der 1. und 2. Gasfamilie, deren Zusammensetzung in EN 437 angegeben ist, bei maximalen Arbeitsdrücken bis zu 420 bar, Betriebsdurchflüssen bis zu 25 000 m3/h über einen Gastemperaturbereich von mindestens 40 K und einem Umgebungstemperaturbereich von mindestens 50 K benutzt werden.
Dieses Dokument gilt für Zähler an Standorten, an denen unbedeutende Vibrationen und Stöße auftreten können, sowie an
— geschlossenen Standorten (innen oder außen mit dem vom Hersteller vorgeschriebenen Schutz) mit oder ohne Betauung
oder, bei entsprechender Angabe durch den Hersteller, an
— offenen Standorten (außen ohne Abdeckung) mit oder ohne Betauung
und an Standorten mit elektromagnetischen Störungen.
Soweit in diesem Dokument nicht anders angegeben:
— sind alle dargestellten Drücke als Überdrücke zu verstehen;
— werden alle Einflussgrößen außer der geprüften Einflussgröße relativ konstant bei ihrem Referenzwert gehalten.
Compteurs de gaz - Compteurs de gaz à turbine
Ce document définit les conditions de mesure, les exigences et les essais applicables à la construction, à la performance et à la sécurité des compteurs de gaz à turbine axiale et radiale de classe 1,0 munis d’indicateurs mécaniques, désignés ci-après sous l’appellation « compteurs », ayant des raccordements sur des canalisations en ligne pour mesure de débit des gaz.
Ce document s'applique aux compteurs de gaz à turbine utilisés pour mesurer le volume des gaz combustibles des 1ère et 2ème familles de gaz, dont la composition est spécifiée dans l’EN 437, à des pressions maximales de service allant jusqu'à 420 bar, à des débits réels allant jusqu'à 25 000 m³/h sur une plage de températures du gaz d’au moins 40 K et une plage de température d’environnement climatique d’au moins 50 K.
Ce document s'applique aux compteurs installés dans des emplacements où les vibrations et les chocs sont peu importants et :
- dans des emplacements fermés (en intérieur ou en extérieur avec la protection spécifiée par le fabricant) avec ou sans condensation d'humidité ;
ou, si le constructeur le spécifie,
- dans des emplacements ouverts (en extérieur sans protection) avec ou sans condensation d'humidité ;
ainsi que dans des emplacements avec interférences électromagnétiques.
Sauf spécification contraire dans le présent document :
- toutes les pressions utilisées sont des pressions relatives ;
- toutes les grandeurs d'influence, sauf celle qui est soumise à l'essai, sont maintenues relativement constantes à leur valeur de référence.
Plinomeri - Turbinski plinomeri
Ta dokument določa pogoje, zahteve, preskuse in pogoje merjenja za gradnjo, delovanje in varnost aksialnih in radialnih turbinskih plinomerov razreda 1,0 z mehanskimi kazalnimi napravami, v nadaljnjem besedilu merilniki, s serijskimi cevnimi priključki za merjenje pretoka plina.
Ta dokument se nanaša na turbinske plinomere, ki se uporabljajo za merjenje prostornine gorivnih plinov iz 1. in 2. družine, katerih sestava je določena v EN 437, pri največjem delovnem tlaku do 420 bar, dejanski hitrosti pretoka do 25 000 m3/h pri temperaturi plina preko 40 K in za klimatsko okoljsko temperaturo vsaj 50 K.
Ta dokument se nanaša na merilnike, ki so nameščeni na mestih, kjer so prisotni tresljaji in udarci majhnega pomena in v
– zaprtih lokacijah (znotraj ali na prostem z zaščito, kot jo določa proizvajalec) s kondenzirano ali nekondenzirano vlago, ali, če je tako določil proizvajalec,
– odprtih lokacijah (na prostem brez kakršnega koli prekritja) s kondenzirano ali nekondenzirano vlago in na lokacijah z elektromagnetnimi motnjami.
Razen če ni drugače določeno v tem dokumentu, velja:
– vsi uporabljeni tlaki so merjeni;
– vse vplivne količine, razen tistih, ki se preizkušajo, so pri njihovi referenčni vrednosti relativno konstantne.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Plinomeri - Turbinski plinomeriGaszähler - TurbinenradgaszählerCompteurs de gaz - Compteurs de gaz à turbineGas meters - Turbine gas meters91.140.40Sistemi za oskrbo s plinomGas supply systemsICS:Ta slovenski standard je istoveten z:EN 12261:2018SIST EN 12261:2018en,fr,de01-maj-2018SIST EN 12261:2018SLOVENSKI
STANDARDSIST EN 12261:2004/AC:2004SIST EN 12261:2004/A1:2006SIST EN 12261:20041DGRPHãþD
SIST EN 12261:2018
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12261
March
t r s z ICS
{ sä s v rä v r Supersedes EN
s t t x sã t r r tEnglish Version
Gas meters æ Turbine gas meters Compteurs de gaz æ Compteurs de gaz à turbine
Gaszähler æ Turbinenradgaszähler This European Standard was approved by CEN on
{ November
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s t t x sã t r s z ESIST EN 12261:2018
EN 12261:2018 (E) 2 Contents Page European foreword . 5 1 Scope . 6 2 Normative references . 6 3 Terms, definitions and symbols . 7 3.1 Terms and definitions . 7 3.2 Symbols . 10 4 Meter classification . 11 4.1 Flange pressure ratings . 11 4.2 Gas meter sizes, rangeability and connection diameter sizes . 12 4.3 Connections and dimensions . 13 4.4 Temperature ranges . 13 4.5 Climatic environment . 13 5 Metrological performance requirements . 13 5.1 General . 13 5.2 Type testing . 14 5.2.1 Error of indication . 14 5.2.2 Metrological stability . 15 5.2.3 Linearity .
...
SLOVENSKI STANDARD
oSIST prEN 12261:2017
01-julij-2017
Plinomeri - Turbinski plinomeri
Gas meters - Turbine gas meters
Gaszähler - Turbinenradgaszähler
Compteurs de gaz - Compteurs de gaz à turbine
Ta slovenski standard je istoveten z: prEN 12261
ICS:
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
oSIST prEN 12261:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 12261:2017
---------------------- Page: 2 ----------------------
oSIST prEN 12261:2017
DRAFT
EUROPEAN STANDARD
prEN 12261
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2017
ICS 91.140.40 Will supersede EN 12261:2002
English Version
Gas meters - Turbine gas meters
Compteurs de gaz - Compteurs de gaz à turbine Gaszähler - Turbinenradgaszähler
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 237.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12261:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 12261:2017
prEN 12261:2017 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and symbols . 6
4 Meter classification . 10
5 Metrological performance requirements . 12
6 Design and material requirements . 19
7 Meter output . 30
8 Marking . 34
9 Documentation . 35
Annex A (normative) Test facility specifications . 37
A.1 Test medium . 37
A.2 Leakage .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.