SIST EN ISO 9658:2024

SLOVENSKI STANDARD
01-december-2024
Jeklo - Določevanje aluminija - Metoda plamenske atomske absorpcijske
spektrometrije (ISO 9658:2024)
Steel - Determination of aluminium content - Flame atomic absorption spectrometric
method (ISO 9658:2024)
Stahl - Bestimmung des Aluminiumgehaltes -
Flammenatomextinktionsspektrometrisches Verfahren (ISO 9658:2024)
Aciers - Détermination de l'aluminium - Méthode par spectrométrie d'absorption
atomique dans la flamme (ISO 9658:2024)
Ta slovenski standard je istoveten z: EN ISO 9658:2024
ICS:
77.040.30 Kemijska analiza kovin Chemical analysis of metals
77.080.20 Jekla Steels
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 9658
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2024
EUROPÄISCHE NORM
ICS 77.080.20 Supersedes EN 29658:1991
English Version
Steel - Determination of aluminium content - Flame atomic
absorption spectrometric method (ISO 9658:2024)
Aciers - Détermination de l'aluminium - Méthode par Stahl - Bestimmung des Aluminiumgehaltes -
spectrométrie d'absorption atomique dans la flamme Flammenatomextinktionsspektrometrisches Verfahren
(ISO 9658:2024) (ISO 9658:2024)
This European Standard was approved by CEN on 16 September 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9658:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 9658:2024) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee CEN/TC 459/SC 2 “Methods of chemical analysis for iron and
steel” the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2025, and conflicting national standards shall
be withdrawn at the latest by March 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 29658:1991.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 9658:2024 has been approved by CEN as EN ISO 9658:2024 without any modification.

International
Standard
ISO 9658
Second edition
Steel — Determination of
2024-09
aluminium content — Flame atomic
absorption spectrometric method
Aciers — Détermination de l'aluminium — Méthode par
spectrométrie d'absorption atomique dans la flamme
Reference number
ISO 9658:2024(en) © ISO 2024
ISO 9658:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 9658:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Reagents . 2
6 Apparatus . 3
7 Sampling and preparation of the test samples . 4
8 Procedure . 4
8.1 Test portion .4
8.2 Blank test .4
8.3 Determination .4
8.3.1 Preparation of the test solution .4
8.3.2 Preparation of the calibration solutions .5
8.3.3 Adjustment of atomic absorption spectrometer .6
8.3.4 Optimizing the atomic absorption spectrometer settings .6
8.3.5 Spectrometric measurements .7
8.4 Plotting the calibration graph .7
9 Expression of results . 8
9.1 Method of calculation .8
9.2 Precision . . .8
10 Test report . 9
Annex A (informative) Procedures for the determination of instrumental criteria .10
Annex B (informative) Additional information on the international cooperative test .12
Annex C (informative) Graphical representation of precision data .13
Bibliography .15

iii
ISO 9658:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 1, Methods of
determination of chemical composition, in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/TC 459, ECISS - European Committee for Iron and Steel Standardization, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 9658:1990), which has been technically
revised.
The main changes are as follows:
— re-assessment of the precision data;
— updating of the normative references;
— adding of some notes that can contribute to a better accuracy of the method;
— adding a Bibliography.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
International Standard ISO 9658:2024(en)
Steel — Determination of
...