SIST EN 13457:2005/kFprA1:2009
(Amendment)Footwear, leather and imitation leather goods manufacturing machines - Splitting, skiving, cutting, cementing and cement drying machines - Safety requirements
Footwear, leather and imitation leather goods manufacturing machines - Splitting, skiving, cutting, cementing and cement drying machines - Safety requirements
Type 1 amendment.
Maschinen zur Herstellung von Schuhen, Leder- und Kunstlederewaren - Spalt-, Schärf-, Schneid-, Klebstoffauftrag- und Klebstofftrockenmaschinen - Sicherheitsanforderungen
Machines de fabrication de chaussures et d'articles en cuir et en matériaux similaires - Machines à refendre, à parer, à couper, à encoller et à sécher l'adhésif - Prescriptions de sécurité
Stroji za izdelavo obutve ter izdelkov iz usnja in njegovih imitacij - Stroji za cepljenje, brušenje, rezanje ter nanos in sušenje lepila - Varnostne zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13457:2005/kFprA1:2009
01-november-2009
Stroji za izdelavo obutve ter izdelkov iz usnja in njegovih imitacij - Stroji za
cepljenje, brušenje, rezanje ter nanos in sušenje lepila - Varnostne zahteve
Footwear, leather and imitation leather goods manufacturing machines - Splitting,
skiving, cutting, cementing and cement drying machines - Safety requirements
Maschinen zur Herstellung von Schuhen, Leder- und Kunstlederewaren - Spalt-, Schärf-,
Schneid-, Klebstoffauftrag- und Klebstofftrockenmaschinen - Sicherheitsanforderungen
Machines de fabrication de chaussures et d'articles en cuir et en matériaux similaires -
Machines à refendre, à parer, à couper, à encoller et à sécher l'adhésif - Prescriptions de
sécurité
Ta slovenski standard je istoveten z: EN 13457:2004/FprA1
ICS:
59.140.40 Stroji in oprema za Machines and equipment for
proizvodnjo usnja in krzna leather and fur production
61.060 Obuvala Footwear
SIST EN 13457:2005/kFprA1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13457:2005/kFprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 13457:2005/kFprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 13457:2004
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
September 2009
ICS 59.140.40; 61.060
English Version
Footwear, leather and imitation leather goods manufacturing
machines - Splitting, skiving, cutting, cementing and cement
drying machines - Safety requirements
Machines de fabrication de chaussures et d'articles en cuir Maschinen zur Herstellung von Schuhen, Leder- und
et en matériaux similaires - Machines à refendre, à parer, à Kunstlederewaren - Spalt-, Schärf-, Schneid-,
couper, à encoller et à sécher l'adhésif - Prescriptions de Klebstoffauftrag- und Klebstofftrockenmaschinen -
sécurité Sicherheitsanforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 201.
This draft amendment A1, if approved, will modify the European Standard EN 13457:2004. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13457:2004/FprA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13457:2005/kFprA1:2009
EN 13457:2004/FprA1:2009 (E)
Foreword
This document (EN 13457:2004/FprA1:2009) has been prepared by WG 8 of Technical Committee
CEN/TC 201 “Leather and imitation leather goods and footwear manufacturing machinery - Safety”, the
secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
The first reason for amending the published standard EN 13457:2004 is the revision of the EU-Machinery
Directive 98/37/EC into 2006/42/EC, requiring the adaptation of published European Standards cited in the
Official Journal of the European Communities under that Directive.
Additionally at this occasion the normative references have been updated, while also some other limited rather
editorial improvements and corrections have been made.
2
---------------------- Page: 4 ----------------------
SIST EN 13457:2005/kFprA1:2009
EN 13457:2004/FprA1:2009 (E)
1 Modification to the Foreword
th
Delete the existing 4 paragraph and replace it with the following: "For relationship with EU Directive(s), see
informative Annexes ZA and ZB, which are integral parts of this document."
2 Modification to the Introduction
st
Delete the 1 paragraph.
nd
In the 2 paragraph, replace "EN 1070" with "EN ISO 12100".
th
Delete the 5 paragraph.
3 Modification to Clause 1, Scope
1.3:
After “ .intended use” add “ , foreseeable misuse“
1.6:
nd
2 indent: Delete "and prEN 12464-2".
1.7:
Replace the text with the following: "This document is not applicable to splitting, skiving, edge trimming, strip
cutting, cementing and cement drying machines which are manufactured before the date of its publication as
EN."
4 Modification to Clause 2, Normative references
Delete reference to EN 294:1992 and replace it with "EN ISO 13857:2008, Safety of machinery — Safety
distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)".
Replace "EN 349" with "EN 349:1993".
Delete reference to EN 418 and replace it with "EN ISO 13850:2008, Safety of machinery — Emergency stop
— Principles for design (ISO 13850:2006)".
Replace "EN 547-1" with "EN 547-1:1996".
Replace "EN 547-2" with "EN 547-2:1996".
3
---------------------- Page: 5 ----------------------
SIST EN 13457:2005/kFprA1:2009
EN 13457:2004/FprA1:2009 (E)
Delete reference to EN 563 and replace it with the following: "EN ISO 13732-1:2008, Ergonomics of the
thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1:
Hot surfaces (ISO 13732-1:2006)".
Replace "EN 614-1" with "EN 614-1:2006".
Add "EN 626-2:1996, Safety of machinery – Reduction of risk to health from hazardous substances emitted by
machinery – Part 2: Methodology leading to verification procedures".
Delete reference to EN 811.
Replace "EN 894-2" with "EN 894-2:1997".
Replace "EN 894-3" with "EN 894-3:2000".
Delete reference to EN 954-1 and replace it with the following: "EN ISO 13849-1:2008, Safety of machinery —
Safety-related parts of control systems — Part 1: General principles for design (ISO 13849-1:2006)".
Replace "EN 999" with "EN 999:1998".
Replace "EN 1037" with "EN 1037:1995".
Delete reference "EN 1050".
Delete reference "EN 1070".
Replace "EN 1127-1:1997" with "EN 1127-1:2007".
Replace "EN 1760-1" with "EN 1760-1:1997".
Replace "EN 1760-2" with "EN 1760-1:2001".
Replace "EN 12464-1" with "EN 12464-1:2002".
Delete reference "prEN 12464-2".
Replace "EN 13478" with "EN 13478:2001".
Replace EN 60204-1:1997 with "EN 60204-1:2006, Safety of machinery — Electrical equipment of machines
— Part 1: General requirements (IEC 60204-1:2005 (modified))".
Add "EN 61310-1, Safety of machinery – Indication, marking and actuation – Part 1: Requirements for visual,
acoustic and tactile signals (IEC 61310-1:2007)"
Replace IEC 61496-2:1997 with the following: "CLC/TS 61496-2:2006, Safety of machinery – Electro-sensitive
protective equipment – Particular requirements for equipment using active opto-electronic protective devices
(AOPDs) (IEC 61496-2:2006)".
Delete the reference to "EN ISO 4871".
Replace "EN ISO 11689" with "EN ISO 11689:1996".
4
---------------------- Page: 6 ----------------------
SIST EN 13457:2005/kFprA1:2009
EN 13457:2004/FprA1:2009 (E)
5 Modification to Clause 3, Terms and definitions
Replace the text in the Introductory paragraph with the following: "For the purposes of this document, the
terms and definitions given in EN ISO 12100-1:2003 and the following apply."
3.2
nd
Replace in the 2 sentence "moving" with "rotating".
6 Modification to Clause 4, List of hazards
Replace the heading of this clause as well as the heading of Table 1 (3 times) with the following: "List of
significant hazards".
Add a new sub-clause 4.1 with the following text: "This clause contains all the significant hazards, hazardous
situations and events, as far as they are dealt with in this document, identified by risk assessment as
significant for this type of machinery and which require action to eliminate or reduce the risk.".
Renumber "4.1" into "4.2" and replace the existing text with the following: "The significant hazards of splitting,
skiving, edge trimming, strip cutting, cementing and cement drying machines are outlined in Table 1 (4 3 to
4.12).”.
Delete the present sub-clause 4.2.
7 Modification to Clause 5, Safety requirements and/or measures
Replace in the headline “or measures“ with “or protective measures“.
5.1:
nd st
Replace in the 2 sentence of the 1 paragraph "should" with "shall".
nd
Replace in the 2 paragraph "EN 294" with "EN ISO 13857".
nd
Replace in the 2 paragraph "EN 418" with "EN ISO 13850".
5.2.1.1:
Replace the existing text with the following: "All transmission machinery and drive mechanisms shall be
safeguarded by fixed enclosing guards which meet the requirements of EN 953 and A.4.".
5.2.1.2.1:
Replace in the introductory text “a risk assessment and in accordance with EN 1050” with
“usability/applicability”.
st
Replace the text of the 1 indent with the following: "fixed enclosing guards which meet the requirements of
A.4 and EN 953; or".
nd
Replace the text of the 2 indent with the following: "fencing which meets the requirements of A.3 and A.4;
or".
5
---------------------- Page: 7 ----------------------
SIST EN 13457:2005/kFprA1:2009
EN 13457:2004/FprA1:2009 (E)
rd
Replace the text of the 3 indent with the following: "fixed covers which meet the requirements of A.1 and A.4;
or".
5.2.1.2.3:
Replace "EN 294:1992" with "EN ISO 13857:2008".
5.2.2.1:
nd
Replace in the 2 sentence of the introductory paragraph "EN 60204-1:1997" with "EN 60204-1:2006".
th
Replace in the 5 indent "12.3" with "11.3".
5.2.3:
st
Replace in the 1 sentence "EN 563" with "EN ISO 13732-1".
nd
Replace in the 2 sentence "EN 563:1994" with "EN ISO 13732-1:2008".
5.2.4.4:
nd
Replace the 2 sentence with the following "The parts of the control system related to the interlocking shall
present at least a performance level "c" defined in accordance with EN ISO 13849-1.".
5.2.7:
nd
Delete in the last indent of the 2 paragraph "and prEN 12464-2".
5.2.9.1:
st
Replace in the 1 indent "EN 60204-1:1997" with "EN 60204-1:2006".
5.2.9.2:
st
Replace in the 1 sentence "EN 954-1" with "EN ISO 13849-1".
5.2.9.3:
st st
Replace the text of the 1 indent of the 1 paragraph with the following "safety related parts of pneumatic and
hydraulic control systems shall present at least a performance level "c" defined in accordance with EN ISO
13849-1;".
nd st
Replace the text of the 2 indent of the 1 paragraph with the following "safety related parts of electrical /
electronic control systems shall normally present at least a performance level "d" defined in accordance with
EN ISO 13849-1. Depending on the risk assessment the parts of the control system related to the emergency
stop system shall present a performance level of at least "c" defined in accordance with EN ISO 13849-1.".
6
---------------------- Page: 8 ----------------------
SIST EN 13457:2005/kFprA1:2009
EN 13457:2004/FprA1:2009 (E)
nd
Replace the 2 paragraph with the following:
"NOTE This requirement includes that safety related functions shall not solely rely on normal traditional programmable
electronic systems (PES): the required performance level should be realised by the use of, for example, an additional
hardwired circuit, a redundant solid state channel, or other provisions for redundancy.
when using a performance level "d" (based on the risk assessment) with a category 2 the test interval
shall be as short as required and not more than 4 h.
the parts of the control system processing the signal of a safety device shall comply at least with the
performance level of that device."
5.2.10.1:
Replace "EN 418" with "EN ISO 13850" and "EN 60204-1:1997" with "EN 60204-1:2006".
5.2.11:
Replace in the note "7.1" with "7.3".
5.3.1.3:
Replace "EN 294" with "EN ISO 13857".
5.3.1.5:
Replace the last sentence with the following: "The grinding wheel shall be safeguarded by a fixed eye
protection guard satisfying A.1 and A.4 of this document.".
5.3.2:
st
Replace the text of the 1 indent with the following: "fixed enclosing guards which meet the requirements of
EN 953 and A.4 of this document, or".
5.3.4.1:
st
In the 1 sentence, replace ”EN 294“ with “EN ISO 13857:2008”.
nd
Replace the 2 sentence with the following: "This requirement is met, for example, by using transport rollers
installed on the inlet side the in-running nip of which is safeguarded by a fixed cover satisfying A.1 and A.4 of
this document.".
7
---------------------- Page: 9 ----------------------
SIST EN 13457:2005/kFprA1:2009
EN 13457:2004/FprA1:2009 (E)
5.3.4.2:
st
Replace the 1 sentence with the following: "Circular rotating knife machines shall be fitted with devices
according to A.1 and A.4 of Annex A covering the unused section of the knife.".
5.3.5.2:
Replace “EN 294“ with “EN ISO 13857".
5.3.5.3:
st nd
Replace the text of the 1 indent of the 2 paragraph with the following: "fixed guards in accordance with EN
953 and A.4 or"
5.3.6.1:
Replace “EN 294“ with “EN ISO 13857".
8 Modification to Clause 6, Verification
Heading:
Replace the heading with the following: "Verification of safety requirements and/or protective measures".
Introductory paragraph:
st st
Replace in the 1 indent of the 1 paragraph "EN 294" with "EN ISO 13857" and "EN 954-1" with "EN ISO
13849-1".
nd
Replace the text of the 2 indent with the following: "the performance level of all safety related parts of the
control system is correct,".
Delete the last paragraph of the introduction.
Table 2:
Replace Table 2 with a new Table 2 as follows:
8
---------------------- Page: 10 ----------------------
SIST EN 13457:2005/kFprA1:2009
EN 13457:2004/FprA1:2009 (E)
"
Table 2 — Methods of testing
Clause Subject rel. standards Verification method/clause of rel.
standard
5.2 Common requirements for all machines within the scope
5.2.1.1 Transmission machinery and drive Measurement of
mechanism distances, visual inspection in
accordance with
fixed enclosing guards EN ISO 12100-2: 2003 5.1 and Annex A of this document
EN ISO 13857:2008 Tables 1, 3 and 4
EN 349 minimum gaps
EN 953:1997 Clause 8
5.2.1.2 Moving machinery parts, tools and Measurement of distances, visual
work pieces inspection in accordance with
EN ISO 12100-2:2003 5.1 and Annex A of this document
EN ISO 13857:2008 Tables 1, 3 and 4
EN 349 minimum gaps
5.2.1.2.1 - fixed enclosing guard EN 953:1997 Clause 8
- fixed covers Sub-clause A.1 of this document
- fencing Sub-clause A.3 of this document
- interlocking guard practical examination of function in
accordance with
EN 1088:1995 Clause 7
Sub-clauses B.2/A.2 of this
document
9
---------------------- Page: 11 ----------------------
SIST EN 13457:2005/kFprA1:2009
EN 13457:2004/FprA1:2009 (E)
5.2.1.2.2 - trip devices check of safety component
certification of the manufacturer
according to
• electro-sensitive protective EN 61496-1:2004 Clause 8 (general)
CLC/TS 61496-2:2006 Clause 5 (opto-electric)
devices
Sub-clauses C.2, C.3 of this
document (level, function,
separation, distances)
• mechanical trip devices Sub-clause C.1 of this
document
• pressure sensitive bars EN 1760-2
• hold to run control device Sub-clause D.1 of this
document
5.2.1.2.3 Safety distances and gap limitation EN ISO 13857:2008 Tables 1, 3 and 4
measurement of distances and
gaps as specified in 5.1.1.2.3 of
this document
5.2.1.2.4 Force limitation measurement of force,
Pressure limitation calculation of pressure, as
specified in 5.2.1.2.4 of this
document
5.2.1.3 Operator’s standing area visual inspection as specified in
5.2.1.3 of this document
5.2.2 Electrical equipment examination with suitable
measuring instruments in
accordance with
5.2.2.1 - electrical equipment EN 60204-1:2006 Clause 18
- electrical components EN 60204-1:2006 visual inspection and check in
accordance with
Clauses 4 to 17 and 5.2.2.1 of
this standard
5.2.2.2 operating controls visual inspection in accordance
with
5.2.2.2 of this document
5.2.3 Thermal protection in accordance with
EN ISO 13732-1 5.2.3 and Annex H of this
document, measurements of
surface temperatures, visual
check of precautions adopted
5.2.4 Protection against fire
5.2.4.1 design (general) visual inspection in accordance
with
EN 13478
5.2.4.2 design (dust zones) visual inspection as specified in
5.2.4.2 of this document
5.2.4.3 design (collector, filter) visual inspection check of
m
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.