oSIST prEN ISO 19085-17:2026

SLOVENSKI STANDARD
01-julij-2026
Lesnoobdelovalni stroji - Varnostne zahteve - 17. del: Stroji za lepljenje robnih
trakov z verižnim dodajanjem (ISO/DIS 19085-17:2026)
Woodworking machines - Safety - Part 17: Edge banding machines fed by chains
(ISO/DIS 19085-17:2026)
Holzbearbeitungsmaschinen - Sicherheit - Teil 17: Kantenanleimmaschinen mit
Kettenbandvorschub (ISO/DIS 19085-17:2026)
Machines à bois - Sécurité - Partie 17: Machines à plaquer sur chant à alimentation par
chaînes (ISO/DIS 19085-17:2026)
Ta slovenski standard je istoveten z: prEN ISO 19085-17
ICS:
13.110 Varnost strojev Safety of machinery
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
International
Standard
ISO/DIS 19085-17
ISO/TC 39/SC 4
Woodworking machines — Safety —
Secretariat: UNI
Part 17:
Voting begins on:
Edge banding machines fed by 2026-06-04
chains
Voting terminates on:
2026-08-27
Machines à bois — Sécurité —
Partie 17: Machines à plaquer sur chant à alimentation par
chaînes
ICS: 79.120.10
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 19085-17:2026(en)
DRAFT
ISO/DIS 19085-17:2026(en)
International
Standard
ISO/DIS 19085-17
ISO/TC 39/SC 4
Woodworking machines — Safety —
Secretariat: UNI
Part 17:
Voting begins on:
Edge banding machines fed by
2026-06-04
chains
Voting terminates on:
2026-08-27
Machines à bois — Sécurité —
Partie 17: Machines à plaquer sur chant à alimentation par
chaînes
ICS: 79.120.10
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2026
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 19085-17:2026(en)
ii
ISO/DIS 19085-17:2026(en)
Contents Page
Foreword .vi
Introduction .vii
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 3
4 Safety requirements and measures for controls . 10
4.1 Safety and reliability of control systems.10
4.2 Control devices .10
4.2.1 General .10
4.2.2 Hand-held control set .10
4.2.3 Reset device .10
4.3 Start .10
4.3.1 Direct start .10
4.3.2 Start via control power-on .11
4.3.3 Integrated feed . .11
4.3.4 Laser banding unit .11
4.4 Safe stops .11
4.4.1 Stop function .11
4.4.2 Normal stop . 12
4.4.3 Operational stop . 12
4.4.4 Emergency stop . 12
4.5 Braking function of tools . 12
4.6 Operating modes . 12
4.6.1 General . 12
4.6.2 Mode selection . 12
4.6.3 Units’ Manual adjustments mode (MODE 2) . 13
4.6.4 Fine adjustment mode (MODE 3) . 13
4.6.5 Feed chains greasing mode (MODE 4) .14
4.7 Tool speed .14
4.7.1 Speed changing by shifting the belts on the pulleys .14
4.7.2 Speed changing by incremental speed change motor . 15
4.7.3 Speed control by frequency inverter . 15
4.8 Failure of any energy supply . 15
4.9 Manual reset control . 15
4.10 Standstill detection . 15
4.11 Machine moving parts speed monitoring. 15
4.12 Time delay. 15
4.13 Teleservice . 15
4.14 Protection against corruption .16
5 Safety requirements and protective measures against mechanical hazards .16
5.1 Stability .16
5.2 Risk of break-up during operation .16
5.3 Tool and tool fixing design .16
5.3.1 General .16
5.3.2 Spindle locking .16
5.3.3 Circular saw blade fixing device .16
5.3.4 Flange dimension for circular saw blades .16
5.3.5 Spindle rings.16
5.4 Tool brake . .16
5.5 Safeguards .17
5.5.1 Fixed guards .17
5.5.2 Interlocking moveable guards .17
5.5.3 Hold-to-run control .17

iii
ISO/DIS 19085-17:2026(en)
5.5.4 Two-hand control .17
5.5.5 Electro-sensitive protective equipment (ESPE) .17
5.5.6 Pressure-sensitive protective equipment (PSPE) .17
5.5.7 Enabling control .17
5.6 Prevention of access to hazardous moving parts .17
5.6.1 Guarding of tools installed inside the integral enclosure .17
5.6.2 Guarding of external milling units .18
5.6.3 Guarding of sanding belts.18
5.6.4 Guarding of the edge banding zone .18
5.6.5 Access between machine halves on double-end machines .19
5.6.6 Access to hazard points through the slot between chain beam and top pressure
beam . 20
5.6.7 Guarding of drives . 20
5.6.8 Safeguarding of the feed mechanisms .21
5.6.9 Safeguarding of machine half movement on double-end machines .24
5.7 Impact hazard . 26
5.8 Clamping devices . 26
5.9 Measures against ejection . 26
5.9.1 Devices against ejection and choice of class of guards . 26
5.9.2 Guards of class A, materials and thickness .27
5.9.3 Guards of class B, materials and thickness .27
5.9.4 Devices to minimize ejection of rigid edges .27
5.9.5 Height adjustments of feed mechanism . 28
5.10 Workpiece supports and guides . . 28
5.10.1 General . 28
5.10.2 Roller tables . 28
5.10.3 Roller rails . 28
5.10.4 Additional workpiece support at the outfeed . 28
5.10.5 Transversal infeed device . 29
5.10.6 Automatic panel returner . 29
6 Safety requirements and protective measures against other hazards .30
6.1 Fire . 30
6.2 Noise . 30
6.2.1 Noise reduction at the design stage . 30
6.2.2 Noise emission measurement and declaration .31
6.3 Emission of chips and dust .31
6.4 Electricity .31
6.5 Ergonomics and handling .31
6.6 Lighting .31
6.7 Pneumatics .31
6.8 Hydraulics .31
6.9 Electromagnetic compatibility.31
6.10 Laser .31
6.11 Static electricity.31
6.12 Errors of fitting .32
6.13 Isolation .32
6.14 Maintenance .32
6.15 Risks due to surfaces, edges or angles .32
6.16 Relevant but not significant hazards .32
6.17 Extreme temperatures .32
6.18 Substances .32
6.19 Artificial optical radiation .32
7 Information for use .32
7.1 Warning devices .32
7.2 Marking .32
7.2.1 Marking principles and methods .32
7.2.2 Marking contents . 33
7.3 Instructions . 33

iv
ISO/DIS 19085-17:2026(en)
7.3.1 Instructions principles and drafting . 33
7.3.2 Instructions handbook contents . 33
Annex A (informative) List of significant hazards .35
Annex B (informative) Performance level required .37
Annex C (normative) Brake test.39
Annex D (normative) Impact test for guards .40
Annex E (normative) Noise test code . 41
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Regulation (EU) 2023/1230 aimed to be covered .45

v
ISO/DIS 19085-17:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 4,
Woodworking machines, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 142, Woodworking machines – Safety, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This document is intended to be used in conjunction with ISO 19085-1:2026.
This second edition cancels and replaces the first edition (ISO 19085-17:2021), which has been technically
revised. The main changes are as follows:
— the way of reference from this document to ISO 19085-1:2026 has been simplified, as well as its
explanation in Introduction, and aligned to ISO drafting rules;
— the verification methods at the end of each subclause have been deleted, since self-evident;
— 4.2, 4.6, 7.2, 7.3 have been rearranged, to follow the new subdivision in ISO 19085-1:2026;
— 4.7.3, 5.10 have been subdivided, to follow the new subdivision in ISO 19085-1:2026;
— 5.4, 5.9 have been simplified in structure, for easier reading.
A list of all parts in the ISO 19085 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

vi
ISO/DIS 19085-17:2026(en)
Introduction
The ISO 19085 series provides technical safety requirements for the design and construction of
woodworking machinery, as well as for the content of the relevant instruction handbook. It concerns
designers, manufacturers, suppliers and importers of the machines specified in the Scope.
This document is a type-C standard as stated in ISO 12100.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organisations, market surveillance etc.)
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e. g. for maintenance (small, medium and large enterprises);
— consumers (in case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are
covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or type-B
standards, the requirements of this type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this type-C
standard.
In this document, a subclause can refer to the same subclause of ISO 19085-1:2026 or give specific
requirements or both.
vii
DRAFT International Standard ISO/DIS 19085-17:2026(en)
Woodworking machines — Safety —
Part 17:
Edge banding machines fed by chains
1 Scope
This document specifies the safety requirements and measures for edge banding machines fed by chains or
belts, with manual loading and unloading and maximum workpiece height capacity of 100 mm, capable of
continuous production use, hereinafter referred to also as “machines”.
This document deals with all significant hazards, hazardous situations or hazardous events, listed in
Annex A, relevant to the machines when used as intended and under conditions of misuse which are
reasonably foreseeable, as well as when transported, assembled, adjusted, maintened, dismantling, disabled
and scrapped.
The machines are designed to process in one pass one end (single-end machine) or both ends (double-end
machine) of panels of:
— materials with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2), even with a core
sheet of aluminium light alloy;
— gypsum plaster boards.
Edges to be applied by the machine can be made of:
— paper;
— melamine;
— plastic;
— composite materials;
— aluminium;
— light alloy;
— veneer;
— solid wood.
This document is also applicable to machines fitted with one or more of the following devices or additional
working units, whose hazards have been dealt with:
— hot air banding unit;
— laser banding unit;
— infrared banding unit;
— dynamic processing units;
— sanding belt units;
— milling unit installed out of the integral enclosure at the panel side on single-end machines;

ISO/DIS 19085-17:2026(en)
— milling unit installed out of the integral enclosure between machines halves of double-end machines;
— additional fixed or movable workpiece support along the feed;
— additional infeed workpiece support;
— additional outfeed workpiece support;
— in-feed device for transversal loading of panels in single-end machines;
— intermediate workpiece support in double-end machines;
— automatic panel returner in single-end machines;
— automatic tool changing;
— quick tool changing system;
— automatic multiple edges infeed device;
— workpiece heaters.
This document does not deal with any hazard related to:
a) systems for loading and unloading of the workpiece to a single machine other than automatic panel
returner and infeed and outfeed workpiece supports (e.g. robots);
b) the combination of a single machine being used with other machines (as part of a line);
c) workpiece dividing unit installed out of the integral enclosure or whose tools protrude out of the
integral enclosure;
d) plasma banding unit.
This document is not applicable to machines intended for use in potentially explosive atmosphere nor
manufactured before the date of its publication.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 286-2:2010, Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes —
Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
ISO 7010:2019, Graphical symbols — Safety colours and safety signs — Registered safety signs
ISO 11553-1:2005, Safety of machinery — Laser processing machines — Part 1: General safety requirements
ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 13732-1:2006, Ergonomics of the thermal environment — Methods for the assessment of human responses
to contact with surfaces — Part 1: Hot surfaces
ISO 13849-1:2023, Safety of machinery — Safety-related parts of control systems — Part 1: General principles
for design
ISO/DIS 19085-1, Woodworking machines — Safety — Part 1: Common requirements
IEC 60825-1:2014, Safety of laser products - Part 1: Equipment classification and requirements

ISO/DIS 19085-17:2026(en)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 12100:2010, ISO 13849-1:2023,
ISO/DIS 19085-1:2026 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
edge banding machine
machine designed for banding in one pass the edge on one side of the workpiece (single-end edge banding
machine) or on both sides of the workpiece (double-end edge banding machine), consisting of an edge
banding zone with various units (e.g. for heating, banding, pressing of the edge, etc.), of a zone for additional
operations (e.g. for snipping, trimming, milling, sanding, polishing, chamfering, etc.) and in addition a sizing/
profiling zone that can precede the edge banding zone.
Note 1 to entry: The main parts of a single-end machine and a double-end machine and their terminology are illustrated
in Figure 1 and Figure 2 respectively.
Note 2 to entry: The glue can be applied to the edge or to the workpiece side.
Note 3 to entry: Workpiece feeding can be by chains or by feeding belts.

ISO/DIS 19085-17:2026(en)
Key
1 feed direction
2 top pressure beam
3 chain/belt beam
4 controls
5 edge banding zone
6 additional operation zone
7 integral enclosure
Figure 1 — Example of a single-end machine
3.2
machine half
part of a machine consisting of a frame, chain/belt beam, top pressure beam and
working units
Note 1 to entry: the two machine halves process the two opposite sides of the workpiece in the same pass. One or
both machine halves are capable of opening (distancing) and closing (approaching) to accept workpieces of different
dimensions.
ISO/DIS 19085-17:2026(en)
Key
1 feed direction
2 top pressure beam
3 chain beam
4 controls
5 edge banding zone
6 additional operation zone
7 integral enclosure
8 machine halves
9 feed cross drive shaft
10 intermediate workpiece support
Figure 2 — Example of a double-end machine
3.3
integral enclosure
guarding designed to fit close to the single-end machine or to each machine half (3.2) of double-end machines,
where certain setting adjustments can be available outside the enclosure
Note 1 to entry: the integral enclosure can also attenuate noise
3.4
gluing unit
unit for the adhesion of the edge to the panel by any technology
Note 1 to entry: Hot melt banding unit (3.5), hot air banding unit (3.6), laser banding unit (3.7), infrared banding unit
(3.8) are kinds of gluing unit, and can be alternative or additional to each other in a machine.

ISO/DIS 19085-17:2026(en)
3.5
hot melt banding unit
unit using hot melt glue for edge banding
3.6
hot air banding unit
unit heating the edge using high temperature compressed air for edge banding, without addition of glue
3.7
laser banding unit
unit heating the edge using laser radiation for edge banding, without addition of glue
3.8
infrared banding unit
unit heating the edge using infrared radiation for edge banding, without addition of glue
3.9
workpiece heater
device to pre-heat the panel before the edge is banded to the panel
Note 1 to entry: Workpiece heater is different from the units heating the edge for adhesion activation
3.10
dynamic processing unit
unit which moves with the workpiece during processing and returns to its starting position ready for the
following (succeeding) workpiece
Note 1 to entry: An example of dynamic processing unit is shown in Figure 3.
Key
1 dynamic processing unit (e.g. sniper saw)
2 feed direction
3 movement zone
Figure 3 — Example of a dynamic processing unit

ISO/DIS 19085-17:2026(en)
3.11
external milling unit
milling unit installed out of the integral enclosure at the panel side for grooving
along the lower surface of the processed panel or for grooving/milling along the panel side opposite to the
banded one
Note 1 to entry: An example of external milling unit for grooving along the lower surface of the processed panel or
along the panel side opposite to the banded one in single-end machines is shown in Figure 4.
Note 2 to entry: An example of external milling unit for milling along the panel side opposite to the banded one in
single-end machines is shown in Figure 5.
Figure 4 — Example of unit for grooving along the lower surface of the processed panel or along the
panel side opposite to the banded one
Key
1 feed direction
2 workpiece guide
3 external milling unit
4 tools inside the integral enclosure
Figure 5 — Example of unit for milling along the panel side opposite to the banded one

ISO/DIS 19085-17:2026(en)
3.12
external milling unit
milling unit installed out of the integral enclosure between machines halves for
grooving along the lower surface of the processed panel
Note 1 to entry: An example of external milling unit in double-end machines is shown in Figure 9, key 7.
3.13
additional workpiece support
workpiece support with the purpose of facilitating manipulation and manual loading or unloading of panels
Note 1 to entry: An additional workpiece support can be installed at the infeed or at the outfeed side of the machine.
3.14
transversal infeed device
power-driven device for transversal loading of panels at right angle respect to the
feed direction
Note 1 to entry: An example of transversal infeed device is shown in Figure 6.
Key
1 feed direction
2 moving arm
3 workpiece clamping device/pins
Figure 6 — Example of transversal infeed device
3.15
intermediate workpiece support
retractable workpiece support positioned between the machine halves

ISO/DIS 19085-17:2026(en)
3.16
automatic panel returner
powered system bringing the panel from the machine end back to the loading
position
Note 1 to entry: An example of automatic panel returner is shown in Figure 16
3.17
dog
lug
element protruding from the feed chain aimed at improving workpiece guidance during
machining
Note 1 to entry: An example of a feed chain provided with dogs is shown in Figure 7.
Key
1 feed chain
2 dogs or lugs
Figure 7 — Example of a feed chain provided with dogs
3.18
jog control
control device for momentary activation of a function or a movement
3.19
MODE 2
units’ manual adjustment mode
condition with safeguards disabled for manual adjustment of processing units not containing rotating tools
...