ISO 10228:2011
(Main)Cross-country skis — Binding mounting area — Requirements for test screws
Cross-country skis — Binding mounting area — Requirements for test screws
ISO 10228:2011 specifies the dimensions, mechanical properties and fastening characteristics of test screws used for testing the binding mounting area of cross-country skis.
Skis de fond — Zone de montage de la fixation — Exigences pour les vis d'essai
L'ISO 10228:2011 spécifie les dimensions, les propriétés mécaniques et les caractéristiques de tenue des vis d'essai utilisées lors de l'essai réalisé sur Ia zone de montage de la fixation des skis de fond.
Tekaške smuči - Območje montaže varnostnih vezi - Zahteve za preskusne vijake
Ta mednarodni standard določa dimenzije, mehanske lastnosti in lastnosti pritrjevanja preskusnih vijakov za preskušanje območja montaže varnostnih vezi pri tekaških smučeh.
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 10228
Second edition
2011-05-15
Cross-country skis — Binding mounting
area — Requirements for test screws
Skis de fond — Zone de montage de la fixation — Exigences pour les
vis d'essai
Reference number
ISO 10228:2011(E)
©
ISO 2011
---------------------- Page: 1 ----------------------
ISO 10228:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 10228:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10228 was prepared by Technical Committee ISO/TC 83, Sports and recreational equipment,
Subcommittee SC 4, Snowsports equipment.
This second edition cancels and replaces the first edition (ISO 10228:1991), which has been technically
revised.
© ISO 2011 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 10228:2011(E)
Introduction
The use of test screws ensures the comparability of measurement data, which are determined by the
manufacturer or other institutions by testing the binding mounting area of cross-country skis.
iv © ISO 2011 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 10228:2011(E)
Cross-country skis — Binding mounting area — Requirements
for test screws
1 Scope
This International Standard specifies the dimensions, mechanical properties and fastening characteristics of
test screws used for testing the binding mounting area of cross-country skis.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1478, Tapping screws thread
ISO 2702, Heat-treated steel tapping screws — Mechanical properties
ISO 7794, Cross-country skis — Ski-binding screws — Requirements
ISO 7
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Skis de fond -- Zone de montage de la fixation -- Exigences pour les vis d'essaiCross-country skis -- Binding mounting area -- Requirements for test screws97.220.20Oprema za zimske športeWinter sports equipmentICS:Ta slovenski standard je istoveten z:ISO 10228:2011oSIST ISO 10228:2011en01-december-2011oSIST ISO 10228:2011SLOVENSKI
STANDARD
oSIST ISO 10228:2011
Reference numberISO 10228:2011(E)© ISO 2011
INTERNATIONAL STANDARD ISO10228Second edition2011-05-15Cross-country skis — Binding mounting area — Requirements for test screws Skis de fond — Zone de montage de la fixation — Exigences pour les vis d'essai
oSIST ISO 10228:2011
ISO 10228:2011(E)
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2011 – All rights reserved
oSIST ISO 10228:2011
ISO 10228:2011(E) © ISO 2011 – All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10228 was prepared by Technical Committee ISO/TC 83, Sports and recreational equipment, Subcommittee SC 4, Snowsports equipment. This second edition cancels and replaces the first edition (ISO 10228:1991), which has been technically revised.
oSIST ISO 10228:2011
ISO 10228:2011(E) iv © ISO 2011 – All rights reserved Introduction The use of test screws ensures the comparability of measurement data, which are determined by the manufacturer or other institutions by testing the binding mounting area of cross-country skis.
oSIST ISO 10228:2011
INTERNATIONAL STANDARD ISO 10228:2011(E) © ISO 2011 – All rights reserved 1 Cross-country skis — Binding mounting area — Requirements for test screws 1 Scope This International Standard specifies the dimensions, mechanical properties and fastening characteristics of test screws used for testing the binding mounting area of cross-country skis. 2 Normative references The following referenced documents are indispensable for the application of thi
...
SLOVENSKI STANDARD
SIST ISO 10228:2012
01-marec-2012
1DGRPHãþD
SIST ISO 10228:1995
7HNDãNHVPXþL2EPRþMHPRQWDåHYDUQRVWQLKYH]L=DKWHYH]DSUHVNXVQHYLMDNH
Cross-country skis -- Binding mounting area -- Requirements for test screws
Skis de fond -- Zone de montage de la fixation -- Exigences pour les vis d'essai
Ta slovenski standard je istoveten z: ISO 10228:2011
ICS:
97.220.20 Oprema za zimske športe Winter sports equipment
SIST ISO 10228:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 10228:2012
---------------------- Page: 2 ----------------------
SIST ISO 10228:2012
INTERNATIONAL ISO
STANDARD 10228
Second edition
2011-05-15
Cross-country skis — Binding mounting
area — Requirements for test screws
Skis de fond — Zone de montage de la fixation — Exigences pour les
vis d'essai
Reference number
ISO 10228:2011(E)
©
ISO 2011
---------------------- Page: 3 ----------------------
SIST ISO 10228:2012
ISO 10228:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 10228:2012
ISO 10228:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10228 was prepared by Technical Committee ISO/TC 83, Sports and recreational equipment,
Subcommittee SC 4, Snowsports equipment.
This second edition cancels and replaces the first edition (ISO 10228:1991), which has been technically
revised.
© ISO 2011 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 10228:2012
ISO 10228:2011(E)
Introduction
The use of test screws ensures the comparability of measurement data, which are determined by the
manufacturer or other institutions by testing the binding mounting area of cross-country skis.
iv © ISO 2011 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 10228:2012
INTERNATIONAL STANDARD ISO 10228:2011(E)
Cross-country skis — Binding mounting area — Requirements
for test screws
1 Scope
This International Standard specifies the dimensions, mechanical properties and fastening characteristics of
test screws used for testing the binding mounting area of cross-country skis.
2
...
NORME ISO
INTERNATIONALE 10228
Deuxième édition
2011-05-15
Skis de fond — Zone de montage de la
fixation — Exigences pour les vis d'essai
Cross-country skis — Binding mounting area — Requirements for test
screws
Numéro de référence
ISO 10228:2011(F)
©
ISO 2011
---------------------- Page: 1 ----------------------
ISO 10228:2011(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2011
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2011 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 10228:2011(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 10228 a été élaborée par le comité technique ISO/TC 83, Matériel de sports et d'activités de plein air,
sous-comité SC 4, Équipements de sport de neige.
Cette deuxième édition annule et remplace la première édition (ISO 10228:1991), qui a fait l'objet d'une
révision technique.
© ISO 2011 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 10228:2011(F)
Introduction
L'utilisation de vis d'essai permet de comparer les données de mesure qui sont déterminées par le fabricant
ou par tout autre organisme lors de l'essai réalisé sur la zone de montage de la fixation des skis de fond.
iv © ISO 2011 – Tous droits réservés
---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 10228:2011(F)
Skis de fond — Zone de montage de la fixation — Exigences
pour les vis d'essai
1 Domaine d'application
La présente Norme internationale spécifie les dimensions, les propriétés mécaniques et les caractéristiques
de tenue des vis d'essai utilisées lors de l'essai réalisé sur Ia zone de montage de la fixation des skis de fond.
2 Références normatives
Les documents de référence suivants sont indispensables à l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 1478, Filetage de vis à tôle
ISO 2702, Vis à tôle en acier traité thermiquement ― Caractéristiques mécaniques
ISO 7794, Skis de fond ― Vis de fixation ― Exigences
ISO 7795, Skis de fond ― Vis de fixation ― Méthode
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.