Large yachts — Strength, weathertightness and watertightness of glazed openings — Part 3: Quality assurance, installation and in-service inspection

This document specifies — the content of the product data sheet of glazing materials for use on yachts, — the evaluation of conformity to the product data sheet of laminated glass and laminated safety glass for use on yachts, — the product labelling and identification methods for glass supplied for installation on board a yacht, and — methods for survey of installed glazing. It does not cover distortion of view or aesthetic aspects.

Grands yachts — Résistance, imperméabilité au mauvais temps et étanchéité des ouvertures vitrées — Partie 3: Assurance qualité, installation et inspection en service

General Information

Status
Published
Publication Date
18-Jun-2019
Current Stage
Ref Project

Buy Standard

Standard
ISO 11336-3:2019 - Large yachts — Strength, weathertightness and watertightness of glazed openings — Part 3: Quality assurance, installation and in-service inspection Released:6/19/2019
English language
30 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 11336-3:2019 - Large yachts -- Strength, weathertightness and watertightness of glazed openings
English language
30 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


INTERNATIONAL ISO
STANDARD 11336-3
First edition
2019-06
Large yachts — Strength,
weathertightness and watertightness
of glazed openings —
Part 3:
Quality assurance, installation and in-
service inspection
Grands yachts — Résistance, imperméabilité au mauvais temps et
étanchéité des ouvertures vitrées —
Partie 3: Assurance qualité, installation et inspection en service
Reference number
©
ISO 2019
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements for glazing material products . 3
4.1 Product data sheet . 3
4.1.1 General. 3
4.1.2 Data to be provided for all glazing materials . 4
4.1.3 Data to be provided for monolithic glazing materials and monolithic
glazing components . 4
4.1.4 Data to be provided for laminated safety glass and for compound glazing
materials . 5
4.1.5 Insulated glazing units . 5
4.2 Detailed description of the properties . 6
4.2.1 Mechanical properties . 6
4.2.2 Post failure behaviour . 7
4.3 Dangerous substances . 9
4.4 Durability . 9
4.5 Suitability for application on control positions . 9
5 Evaluation of conformity .10
5.1 General .10
5.2 Initial examination .10
5.3 Factory production control .10
6 Marking and/or labelling .10
6.1 General .10
6.2 Product marking .10
6.3 Product records .10
7 Information to be provided to the vessel .10
8 Inspection during installation .11
9 Lifetime inspections.13
9.1 General .13
9.2 Inspections .13
9.3 Inspection of glazing .13
9.3.1 General.13
9.3.2 Inspection of glazing containing TTG .13
9.3.3 Inspection of glazing containing CSG .14
9.3.4 Inspection of laminated glazing and glazing with materials other than glass .14
9.4 Inspection of bonding .14
9.5 Durability of materials .14
9.6 Routine inspections .15
9.6.1 Signs of deterioration .15
9.6.2 Signs of malfunctioning.15
9.7 Further investigation .16
9.8 Replacement or renewal of bonding and sealing. .16
Annex A (normative) Tests for ensuring conformity .17
Annex B (informative) Laminated safety glass: Mechanical resistance tests .18
Annex C (informative) Criteria for deciding if a change within an assembly requires a new
initial type test .22
Annex D (informative) Background notes on certain clauses in this document .23
Annex E (informative) Application of the Weibull distribution .25
Annex F (normative) Information to be supplied to the vessel .26
Annex G (informative) Example of bonding record .27
Annex H (informative) Example of inspection record .29
Bibliography .30
iv © ISO 2019 – All rights reserved

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 8, Ships and marine technology,
Subcommittee SC 12, Large yachts.
A list of all parts in the ISO 11336 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
INTERNATIONAL STANDARD ISO 11336-3:2019(E)
Large yachts — Strength, weathertightness and
watertightness of glazed openings —
Part 3:
Quality assurance, installation and in-service inspection
1 Scope
This document specifies
— the content of the product data sheet of glazing materials for use on yachts,
— the evaluation of conformity to the product data sheet of laminated glass and laminated safety glass
for use on yachts,
— the product labelling and identification methods for glass supplied for installation on board a
yacht, and
— methods for survey of installed glazing.
It does not cover distortion of view or aesthetic aspects.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 1288-3, Glass in building — Determination of the bending strength of glass — Part 3: Test with
specimen supported at two points (four point bending)
ISO 11336-1:2012, Large yachts — Strength, weathertightness and watertightness of glazed openings —
Part 1: Design criteria, materials, fra
...


INTERNATIONAL ISO
STANDARD 11336-3
First edition
2019-06
Large yachts — Strength,
weathertightness and watertightness
of glazed openings —
Part 3:
Quality assurance, installation and in-
service inspection
Grands yachts — Résistance, imperméabilité au mauvais temps et
étanchéité des ouvertures vitrées —
Partie 3: Assurance qualité, installation et inspection en service
Reference number
©
ISO 2019
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements for glazing material products . 3
4.1 Product data sheet . 3
4.1.1 General. 3
4.1.2 Data to be provided for all glazing materials . 4
4.1.3 Data to be provided for monolithic glazing materials and monolithic
glazing components . 4
4.1.4 Data to be provided for laminated safety glass and for compound glazing
materials . 5
4.1.5 Insulated glazing units . 5
4.2 Detailed description of the properties . 6
4.2.1 Mechanical properties . 6
4.2.2 Post failure behaviour . 7
4.3 Dangerous substances . 9
4.4 Durability . 9
4.5 Suitability for application on control positions . 9
5 Evaluation of conformity .10
5.1 General .10
5.2 Initial examination .10
5.3 Factory production control .10
6 Marking and/or labelling .10
6.1 General .10
6.2 Product marking .10
6.3 Product records .10
7 Information to be provided to the vessel .10
8 Inspection during installation .11
9 Lifetime inspections.13
9.1 General .13
9.2 Inspections .13
9.3 Inspection of glazing .13
9.3.1 General.13
9.3.2 Inspection of glazing containing TTG .13
9.3.3 Inspection of glazing containing CSG .14
9.3.4 Inspection of laminated glazing and glazing with materials other than glass .14
9.4 Inspection of bonding .14
9.5 Durability of materials .14
9.6 Routine inspections .15
9.6.1 Signs of deterioration .15
9.6.2 Signs of malfunctioning.15
9.7 Further investigation .16
9.8 Replacement or renewal of bonding and sealing. .16
Annex A (normative) Tests for ensuring conformity .17
Annex B (informative) Laminated safety glass: Mechanical resistance tests .18
Annex C (informative) Criteria for deciding if a change within an assembly requires a new
initial type test .22
Annex D (informative) Background notes on certain clauses in this document .23
Annex E (informative) Application of the Weibull distribution .25
Annex F (normative) Information to be supplied to the vessel .26
Annex G (informative) Example of bonding record .27
Annex H (informative) Example of inspection record .29
Bibliography .30
iv © ISO 2019 – All rights reserved

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 8, Ships and marine technology,
Subcommittee SC 12, Large yachts.
A list of all parts in the ISO 11336 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
INTERNATIONAL STANDARD ISO 11336-3:2019(E)
Large yachts — Strength, weathertightness and
watertightness of glazed openings —
Part 3:
Quality assurance, installation and in-service inspection
1 Scope
This document specifies
— the content of the product data sheet of glazing materials for use on yachts,
— the evaluation of conformity to the product data sheet of laminated glass and laminated safety glass
for use on yachts,
— the product labelling and identification methods for glass supplied for installation on board a
yacht, and
— methods for survey of installed glazing.
It does not cover distortion of view or aesthetic aspects.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 1288-3, Glass in building — Determination of the bending strength of glass — Part 3: Test with
specimen supported at two points (four point bending)
ISO 11336-1:2012, Large yachts — Strength, weathertightness and watertightness of glazed openings —
Part 1: Design criteria, materials, fra
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.