iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ISO

ISO 7176-3:2012

(Main)

Wheelchairs — Part 3: Determination of effectiveness of brakes

Wheelchairs — Part 3: Determination of effectiveness of brakes

ISO 7176-3:2012 specifies test methods for the measurement of the effectiveness of brakes of manual wheelchairs and electrically powered wheelchairs, including scooters, intended to carry one person, with a maximum speed not exceeding 15 km/h. It also specifies disclosure requirements for the manufacturer.

Fauteuils roulants — Partie 3: Détermination de l'efficacité des freins

L'ISO 7176-3:2012 spécifie des méthodes d'essai permettant de mesurer l'efficacité des freins des fauteuils roulants manuels et électriques, y compris les scooters, destinés à transporter une personne à une vitesse maximale ne dépassant pas 15 km/h. Elle spécifie également les exigences que le fabricant doit rendre publiques.

General Information

Status
Published
Publication Date
10-Dec-2012
ICS
11.180.10 - Aids and adaptation for moving
Technical Committee
ISO/TC 173/SC 1 - Wheelchairs
Drafting Committee
ISO/TC 173/SC 1/WG 1 - Test methods
Current Stage
9093 - International Standard confirmed
Completion Date
20-Oct-2023
Ref Project

Relations

Revises
ISO 7176-3:2003 - Wheelchairs — Part 3: Determination of effectiveness of brakes
Effective Date
28-Feb-2009

Buy Standard

ISO 7176-3:2012 - WheelchairsISO 7176-3:2012 - Wheelchairs
PreviousNext
Standard
ISO 7176-3:2012 - Wheelchairs
English language
14 pages
sale 15% off
Preview
sale 15% off
Preview
ISO 7176-3:2012 - Fauteuils roulantsISO 7176-3:2012 - Fauteuils roulants
PreviousNext
Standard
ISO 7176-3:2012 - Fauteuils roulants
French language
14 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 7176-3
Third edition
2012-12-15
Wheelchairs —
Part 3:
Determination of effectiveness of
brakes
Fauteuils roulants —
Partie 3: Détermination de l’efficacité des freins
Reference number
ISO 7176-3:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 7176-3:2012(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the
address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 7176-3:2012(E)

Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
6 Preparation of test wheelchair . 3
7 Brake performance . 3
7.1 General . 3
7.2 Parking brakes . 4
7.3 Running brakes, normal operation . 4
7.4 Running brakes, operation by reverse command . 5
7.5 Running brakes, emergency operation . 5
8 Test report . 5
9 Disclosure . 6
Annex A (normative) Brake levers — Determination of operating force .8
Annex B (informative) Manual running brakes — Determination of performance .10
Annex C (informative) Running brakes — Alternative test method .12
Bibliography .
...

NORME ISO
INTERNATIONALE 7176-3
Troisième édition
2012-12-15
Fauteuils roulants —
Partie 3:
Détermination de l’efficacité des freins
Wheelchairs —
Part 3: Determination of effectiveness of brakes
Numéro de référence
ISO 7176-3:2012(F)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 7176-3:2012(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2012
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée
sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans
l’accord écrit de l’ISO à l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2012 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 7176-3:2012(F)

Sommaire Page
Avant-propos .iv
Introduction .vi
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe . 2
5 Appareillage . 2
6 Préparation du fauteuil roulant d’essai . 3
7 Performances de freinage . 4
7.1 Généralités . 4
7.2 Freins de stationnement . 4
7.3 Freins de service, fonctionnement normal . 5
7.4 Freins de service, arrêt par inversion du sens de commande . 5
7.5 Freins de service, fonctionnement d’urgence . 6
8 Rapport d’essai . 6
9 Diffusion d’informations . 6
Annexe A (normative) Leviers de freinage — Détermination de la force de manœuvre .8
Annexe B (informative) Freins de service manuels — Détermination d’efficacité .10
Annexe C (normative) Freins de service — Méthode d’essai alternative .12
Bibliographie .14
© ISO 2012 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 7176-3:2012(F)

Avant-propos
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ISO
ISO/TS 16840-14:2023(Main)
Wheelchair seating — Part 14: Concepts related to managing external forces to maintain tissue integrity

This document describes common terms related to forces and their effects as experienced by human bodies and their support surfaces. It provides further information on concepts around how these forces affect the human body's response to postural support systems, and particularly highlights the impact of the interface between tissues and postural support devices (PSD) on the maintenance of tissue integrity. It provides a general introduction to biomechanical concepts, phenomena, and vocabulary. This is intended to facilitate effective understanding and sharing of information between a range of disciplines/stakeholders involved in providing equipment to manage tissue integrity. Representative stakeholders include people with a disability, occupational therapists, physical therapists, biomedical engineers, nurses, medical and para medical personnel, device manufacturers, and other professionals facilitating development, provision, and access to seating and mobility equipment. This document does not provide detailed information that is currently available in physiological text books or scientific literature.

  • Technical specification
    12 pages
    English language
    sale 15% off
  • Draft
    12 pages
    English language
    sale 15% off
  • Draft
    12 pages
    English language
    sale 15% off
ISO
ISO 7176-31:2023(Main)
Wheelchairs — Part 31: Lithium-ion battery systems and chargers for powered wheelchairs — Requirements and test methods

This document specifies requirements and test methods for lithium-ion batteries and battery systems intended for use in electrically powered wheelchairs, and their charging systems.

  • Standard
    10 pages
    English language
    sale 15% off
  • Draft
    14 pages
    English language
    sale 15% off
ISO
ISO 16840-3:2022(Main)
Wheelchair seating — Part 3: Determination of static, impact, and repetitive load strengths for postural support devices

This document specifies requirements for static, impact, and repetitive load strengths for postural support devices (PSDs) with associated attachment hardware intended for use with an undefined wheelchair seating system. It specifies the test methods for determining whether the minimum performance requirements have been met to release a product into use. It also specifies requirements for disclosure of the test results. Not all tests apply to all PSDs. This document is also applicable to other seating systems. The test methods can be used to verify the manufacturer’s claims that a product meets the requirements of this document. This document does not apply to PSDs that are designed to fail under certain static, dynamic, or repetitive loads. This document does not apply to the strength of PSDs under crash conditions in a motor vehicle. This document does not evaluate long-term useful life. NOTE 1 ISO 16840‑4 provides crash test methods and requirements for wheelchair seating systems when used as part of a wheelchair seat in a motor vehicle. NOTE 2 For user masses greater or less than those specified in this document, appropriate extrapolation of test apparatus dimensions, mounting point separation, forces, etc. can be carried out, and the test parameters noted in the test report. NOTE 3 Rigid surrogate test fixtures are utilized to provide a standardized test method, and consequently this document does not involve a test of a PSD on a particular wheelchair.

  • Standard
    40 pages
    English language
    sale 15% off
  • Standard
    42 pages
    French language
    sale 15% off
ISO
ISO 7176-25:2022(Main)
Wheelchairs — Part 25: Lead-acid batteries and chargers for powered wheelchairs — Requirements and test methods

This document specifies requirements and test methods for lead-acid batteries and their chargers intended for use with electrically-powered wheelchairs and scooters. Requirements for chargers are applicable to those with a rated input voltage not greater than 250 V AC and a nominal output voltage not greater than 36 V.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    17 pages
    English language
    sale 15% off
  • Standard
    22 pages
    French language
    sale 15% off
ISO
ISO 16840-11:2022(Main)
Wheelchair seating — Part 11: Determination of dissipation characteristics of sensible perspiration into seat cushions

This document specifies a method for determining the dissipation characteristics of simulated sensible perspiration exposure on seat cushions of a wheelchair under test conditions that simulate body loading on support surfaces with flat and contoured profiles. The test method is applicable to a wide variety of seat cushion materials and constructions that are used across the world. The test method is intended to determine how the cushion handles a liquid load. It is not intended to determine how the cushion responds to a continuous release of liquid or vapour. This document also specifies apparatus to measure dissipation characteristics (of perspiration) of seat cushions and the approach to be employed in measuring these characteristics. This document is applicable to seat cushions for wheelchairs that include a cushion cover. NOTE The significance of the dissipation characteristics of the seat cushion can be greatly affected by the clothing worn, for example a moisture wicking cover might not help the skin condition of the patient sitting in a wet adult diaper.

  • Standard
    8 pages
    English language
    sale 15% off
ISO
ISO 7176-32:2022(Main)
Wheelchairs — Part 32: Test method for wheelchair castor assembly durability

This document specifies strength requirements and test methods for wheelchair castor assemblies. The test methods include corrosion, abrasion and fatigue conditions. This document also specifies requirements for disclosure of test results. It is applicable to castor assemblies of or developed for use in occupant and to assistant-propelled manual wheelchairs and electrically powered wheelchairs. The test requirements are also applicable to wheelchair castor assemblies not necessarily associated or supplied with a wheelchair. Castor assemblies including those with anti-tip castor wheels that do not touch the ground during wheelchair travel are outside the scope of this document.

  • Standard
    12 pages
    English language
    sale 15% off
ISO
ISO 7176-19:2022(Main)
Wheelchairs — Part 19: Wheelchairs for use as seats in motor vehicles

This document specifies test methods, requirements and recommendations for wheelchairs intended for use as seats in motor vehicles related to design, performance, labelling, presale literature, user instructions and user warnings. This document is applicable to all manual and powered wheelchairs, including scooters, which, in addition to their primary function as wheeled mobility devices, are also likely to be used as forward-facing seats in motor vehicles by children and adults with a body mass equal to or greater than 12 kg. This document is applicable to complete wheelchairs, including a frame or powerbase and seating system. It is also applicable to wheelchairs equipped with additional components designed to facilitate conformity with one or more of the requirements of this document.

  • Standard
    91 pages
    English language
    sale 15% off
  • Standard
    94 pages
    French language
    sale 15% off
  • Draft
    92 pages
    English language
    sale 15% off
ISO
ISO 7176-14:2022(Main)
Wheelchairs — Part 14: Power and control systems for electrically powered wheelchairs and scooters — Requirements and test methods

This document specifies requirements and associated test methods for the power, and control systems of electrically powered wheelchairs and scooters. It sets safety and performance requirements that apply during normal use and some conditions of abuse and failure. It also specifies methods of measurement of the forces necessary to operate controls and sets limits on the forces needed for some operations. This document is applicable to electrically powered wheelchairs and scooters with a maximum speed no greater than 15 km/h intended to provide indoor and/or outdoor mobility for one disabled person whose mass lies in the range specified in ISO 7176-11.

  • Standard
    65 pages
    English language
    sale 15% off
  • Standard
    69 pages
    French language
    sale 15% off
  • Draft
    65 pages
    English language
    sale 15% off
ISO
ISO 16840-12:2021(Main)
Wheelchair seating — Part 12: Envelopment and immersion characterization of seat cushions using a dual semispherical indenter

This document specifies apparatus, test methods, and disclosure requirements for characterization of wheelchair seat cushion immersion and envelopment properties using indenters instrumented with pressure sensors. This document expands the characterization of products intended to manage tissue integrity (ISO 16840‑2) and provides a standardized indenter for other wheelchair seating tests. It does not provide information specific to cushion performance for a particular individual user, nor is it intended to characterize envelopment or immersion under higher loading conditions, nor to assess the weight capacity of a cushion. This document includes a method that is specific to 220 mm and 255 mm indenters. Dimensions are provided for a 380 mm indenter to allow for extension of the method to larger patient simulation.

  • Standard
    15 pages
    English language
    sale 15% off
  • Draft
    15 pages
    English language
    sale 15% off
ISO
ISO 16840-13:2021(Main)
Wheelchair seating — Part 13: Determination of the lateral stability property of a seat cushion

This document specifies apparatus, test methods, and disclosure requirements for determination of lateral stability properties of wheelchair seat cushions by measuring the response from the cushion to a shift in the centre of mass of the load on the cushion. It provides a method of determining changes in a particular physical and mechanical property of the cushion. It does not provide information specific to cushion performance for a particular individual user. It does not provide information related to anterior-posterior stability, nor to stability contributions from cushion edges. NOTE 1 Test conditions simulate a symmetric anatomy. NOTE 2 Loads are intended to represent those seen under the pelvis of a 40th to 60th percentile wheelchair user. This document is applicable to cushions used in situations other than a wheelchair.

  • Standard
    9 pages
    English language
    sale 15% off
  • Draft
    9 pages
    English language
    sale 15% off