ISO 7076-6:2016
(Main)Fire protection — Foam fire extinguishing systems — Part 6: Vehicle mounted compressed air foam systems
Fire protection — Foam fire extinguishing systems — Part 6: Vehicle mounted compressed air foam systems
ISO 7076-6:2016 specifies requirements for compressed air foam systems (CAFS) in which foam concentrate and compressed air are continuously added to the water being discharged from the fire-fighting pump. This part of ISO 7076 is applicable to CAFS that can be permanently installed in fire-fighting vehicles, transportable, or mobile. ISO 7076-6:2016 specifies requirements for CAFS which are used at ambient temperatures ranging from ?10 °C to +40 °C. ISO 7076-6:2016 does not apply to stationary CAFS. ISO 7076-6:2016 does not apply to requirements for hazards related to handling foam concentrates, noise generated by CAFS, drives, auxiliary equipment, power sources, or pumps connected to the CAFS. ISO 7076-6:2016 does not specify requirements for special hazards arising from particular conditions under which CAFS are used, for example: - immunity against electromagnetic fields and electrostatic discharge; - operation without supervision; - events specific to the location where the CAFS is set up (e.g. on public roads); - handling of any equipment, devices, etc., which have to be connected to the CAFS or are joined to it (e.g. branch pipes, nozzles and pressure hoses); - decommissioning and disposal.
Protection contre l'incendie — Systèmes d'extinction d'in cendie à mousse — Partie 6: Équipement pour mousse physique à air comprimé monté sur vehicules
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 7076-6
First edition
2016-06-01
Fire protection — Foam fire
extinguishing systems —
Part 6:
Vehicle mounted compressed air
foam systems
Protection contre l’incendie — Systèmes d’extinction d’in cendie à
mousse —
Partie 6: Équipement pour mousse physique à air comprimé monté
sur vehicules
Reference number
ISO 7076-6:2016(E)
©
ISO 2016
---------------------- Page: 1 ----------------------
ISO 7076-6:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 7076-6:2016(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements . 3
4.1 Compliance . 3
4.1.1 Type assessments . 3
4.1.2 Individual assessments . 3
4.2 Safety and protective measures. 4
4.2.1 General. 4
4.2.2 Mechanical equipment. 4
4.2.3 Components under pressure . 5
4.2.4 Material, parts and components . 5
4.2.5 Hot parts . 5
4.2.6 Electrical equipment . 5
4.2.7 Operator controls and indicators . 5
4.2.8 System failure and continuation of on-going fire-fighting operation . 5
4.2.9 Shutdown control . 6
4.2.10 Maintenance and service . 6
4
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.