ISO 15874-3:2013/Amd 1:2018
(Amendment)Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 1
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 1
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide — Polypropylène (PP) — Partie 3: Raccords — Amendement 1
General Information
- Status
- Published
- Publication Date
- 24-Jun-2018
- Technical Committee
- ISO/TC 138/SC 2 - Plastics pipes and fittings for water supplies
- Current Stage
- 6060 - International Standard published
- Start Date
- 25-Jun-2018
- Due Date
- 12-Sep-2017
- Completion Date
- 12-Sep-2017
Relations
- Effective Date
- 27-Nov-2021
Overview
ISO 15874-3:2013/Amd 1:2018 is an important amendment to the internationally recognized standard for plastics piping systems used in hot and cold water installations. This amendment focuses specifically on polypropylene (PP) fittings, which are commonly used due to their durability, chemical resistance, and thermal stability. Issued by the International Organization for Standardization (ISO), the document updates and expands the specifications for fittings under Part 3 of the ISO 15874 series.
The update reflects increasing industry demands by incorporating larger dimension fittings, enhancing the scope and applicability of polypropylene piping solutions. This amendment supports manufacturers, engineers, and installation professionals seeking to comply with global best practices and quality control requirements, ensuring safety, reliability, and performance in plumbing systems.
Key Topics
- Scope of Amendment: Extension of fittings dimensions, introducing larger sizes from 180 mm up to 250 mm, while maintaining existing ranges from 16 mm to 160 mm unchanged.
- Socket Dimensions for Electrofusion Fittings: Precise nominal diameters and dimensions related to fusion zone length and depth of penetration are updated. These details are critical for achieving high-quality joints in polypropylene piping systems.
- Manufacturing Tolerances: Permits smaller socket dimension values in systems involving spigot trimming, subject to manufacturer specifications.
- International Collaboration: Prepared jointly by ISO Technical Committee ISO/TC 138 and the European Committee for Standardization (CEN/TC 155), under the Vienna Agreement, ensuring harmonized global standards.
- Standardization Process and Intellectual Property: Adheres to ISO/IEC Directives with transparent procedures. Users are informed about patent rights considerations relevant to fittings technology.
- Language and Accessibility: Provided in multiple official languages (English and French), facilitating widespread understanding and adoption.
Applications
ISO 15874-3:2013/Amd 1:2018 applies to a wide range of plastic piping installations for the transport of hot and cold potable water in residential, commercial, and industrial buildings. The polypropylene fittings standardized in this document are typically used in:
- Residential Plumbing Systems: For reliable water supply and heating systems.
- Commercial and Institutional Buildings: Including hospitals, schools, and office complexes requiring robust piping networks.
- Industrial Water Systems: Where chemical and temperature resistance of polypropylene is advantageous.
- Prefabricated Piping Assemblies: Ensuring compatibility and quality during factory production and on-site installation.
- Renovation and Retrofit Projects: Where compliance with updated standards impacts system longevity and safety.
The extended dimension range allows designers and engineers to implement larger piping systems with standardized fittings, improving system scalability without compromising joint integrity.
Related Standards
- ISO 15874 Parts 1, 2, 4, and 5: Covering general conditions, pipes, valves, and specific requirements for polypropylene systems.
- ISO 21307: Relates to polypropylene piping systems intended for soil and waste applications.
- ISO 4435: Standard for polyethylene (PE) piping fittings, offering complementary guidelines for alternative plastic materials.
- EN ISO 21003 Series: European standards harmonizing with ISO 15874 for plastics piping in water installations.
- ISO/IEC Directives, Part 1 and Part 2: Describe rules for the development and editorial process of ISO standards to ensure consistency and clarity.
Keywords: ISO 15874-3:2013 Amendment 1, polypropylene fittings, plastic piping systems, hot and cold water installations, electrofusion fittings, piping standards, water supply systems, polypropylene (PP) pipe fittings, international plumbing standards, piping dimensions, plastic pipe joint specifications.
REDLINE ISO 15874-3:2013/Amd 1:2018 - Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 3: Fittings — Amendment 1 Released:6/25/2018
REDLINE ISO 15874-3:2013/Amd 1:2018 - Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 3: Fittings — Amendment 1 Released:6/25/2018
Frequently Asked Questions
ISO 15874-3:2013/Amd 1:2018 is a standard published by the International Organization for Standardization (ISO). Its full title is "Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 1". This standard covers: Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 1
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 1
ISO 15874-3:2013/Amd 1:2018 is classified under the following ICS (International Classification for Standards) categories: 23.040.45 - Plastics fittings; 91.140.60 - Water supply systems. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 15874-3:2013/Amd 1:2018 has the following relationships with other standards: It is inter standard links to ISO 15874-3:2013. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase ISO 15874-3:2013/Amd 1:2018 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of ISO standards.
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 15874-3
Second edition
2013-02-15
AMENDMENT 1
2018-07
Plastics piping systems for hot
and cold water installations —
Polypropylene (PP) —
Part 3:
Fittings
AMENDMENT 1
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Polypropylène (PP) —
Partie 3: Raccords
AMENDEMENT 1
Reference number
ISO 15874-3:2013/Amd.1:2018(E)
©
ISO 2018
ISO 15874-3:2013/Amd.1:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
ISO 15874-3:2013/Amd.1:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
...
ISO 15874-3:2013/FDAMAMD 1:2018(E)
ISO/TC 138/SC 2 N
Date: 2018-03-1407-01
ISO 15874-3:2013/FDAMAMD 1
ISO/TC 138/SC 2/WG 1
Secretariat: SNV
Plastic piping systems for hot and cold water installations — Polypropylene (PP) —
Part 3: Fittings — Amendment 1
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide
— Polypropylène (PP) — Partie 3: Raccords — Amendement 1
ISO 15874-3:2013/FDAMAMD 1:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an
...
NORME ISO
INTERNATIONALE 15874-3
Deuxième édition
2013-02-15
AMENDEMENT 1
2018-07
Systèmes de canalisations en plastique
pour les installations d'eau chaude et
froide — Polypropylène (PP) —
Partie 3:
Raccords
AMENDEMENT 1
Plastics piping systems for hot and cold water installations —
Polypropylene (PP) —
Part 3: Fittings
AMENDMENT 1
Numéro de référence
ISO 15874-3:2013/Amd.1:2018(F)
©
ISO 2018
ISO 15874-3:2013/Amd.1:2018(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2018
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en oeuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2018 – Tous droits réservés
ISO 15874-3:2013/Amd.1:2018(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
...
ISO 15874-3:2013/FDAMAMD 1:2018(F)
Date: 2018-04-03
ISO 15874-3:2013/FDAMAMD 1
ISO/TC 138/SC 2/WG 1
Secrétariat: SNV
Systèmes de canalisations en plastique pour les installations d’eau chaude et
froide — Polypropylène (PP) — Partie 3: Raccords
AMENDEMENT 1
Plastic piping systems for hot and cold water installations — Polypropylene (PP) —
Part 3: Fittings
AMENDMENT 1
ISO 15874-3:2013/FDAMAMD 1:2018(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en
général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit
de faire partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales
et non gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore
étroitement avec la Commission électrotechnique internationale (IEC) en ce qui concerne la
normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant les
références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de l'élaboration
du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de brevets reçues par
l'ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire de
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...