Indoor air — Part 19: Sampling strategy for moulds

ISO 16000-19:2012 describes the measurement strategy for the detection of fungi in indoor environments. ISO 16000-19:2012 describes suitable sampling and analysis methods together with a description of the applicability and the interpretation of the measurement results to maximize the comparability of the measured data obtained for a given measurement objective. It does not include details on recording building characteristics or field inspections by qualified professionals which have to take place prior to any microbiological measurement. ISO 16000-19:2012 is not applicable to a detailed description of the building physics- and building-engineering-related procedures applicable to field inspections. The methods and procedures presented do not allow quantitative exposure assessment with regard to the room occupants. The application of ISO 16000-19:2012 presupposes the knowledge of ISO 16000-1.

Air intérieur — Partie 19: Stratégie d'échantillonnage des moisissures

L'ISO 16000-19:2012 décrit la stratégie de mesurage pour détecter les champignons dans les environnements intérieurs. L'ISO 16000-19:2012 décrit des méthodes d'échantillonnage et d'analyse appropriées ainsi que l'applicabilité et l'interprétation des résultats de mesurage pour maximiser la comparabilité des données mesurées obtenues pour un objectif de mesurage donné. Elle ne contient pas d'indications détaillées concernant l'enregistrement des caractéristiques du bâtiment ou les inspections sur le terrain menées par des professionnels qualifiés qui doivent être effectués préalablement à tout mesurage microbiologique. L'ISO 16000-19:2012 ne s'applique pas à une description détaillée des modes opératoires relatifs à la physique et au génie du bâtiment applicables aux inspections sur le terrain. Les méthodes et les modes opératoires présentés ne permettent pas d'évaluer l'exposition quantitative des occupants de la pièce. L'application de l'ISO 16000-19:2012 présuppose que l'on ait pris connaissance de l'ISO 16000‑1.

Notranji zrak - 19. del: Strategija vzorčenja gliv

Ta del ISO 16000 opisuje strategijo merjenja za zaznavanje gliv v zaprtih prostorih. Opisuje primerne metode vzorčenja in analize skupaj z opisom uporabnosti in interpretacije rezultatov meritev za povečanje primerljivosti pridobljenih podatkov meritev za dani cilj meritev. Ne vključuje podrobnosti o beleženju lastnosti stavb ali strokovnem pregledu območja, ki se morata izvesti pred mikrobiološkimi merjenji. Ta del standarda ISO 16000 ne velja za podroben opis postopkov, povezanih z gradbeno fiziko ali gradbeno tehniko, ki se uporabljajo pri pregledu območja. Predstavljene metode in postopki ne omogočajo kvantitativnega ocenjevanja izpostavljenosti oseb v prostoru. Uporaba tega dela ISO 16000 predpostavlja poznavanje ISO 16000-1.

General Information

Status
Published
Publication Date
30-May-2012
Current Stage
9093 - International Standard confirmed
Completion Date
04-Jun-2024

Buy Standard

Standard
ISO 16000-19:2013
English language
35 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 16000-19:2014
English language
35 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 16000-19:2012 - Indoor air
English language
29 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 16000-19:2012 - Air intérieur
French language
31 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Air intérieur - Partie 19: Stratégie d'échantillonnage des moisissuresIndoor air - Part 19: Sampling strategy for moulds13.040.20Kakovost okoljskega zrakaAmbient atmospheresICS:Ta slovenski standard je istoveten z:ISO 16000-19:2012oSIST ISO 16000-19:2013en,fr01-april-2013oSIST ISO 16000-19:2013SLOVENSKI
STANDARD



oSIST ISO 16000-19:2013



Reference numberISO 16000-19:2012(E)© ISO 2012
INTERNATIONAL STANDARD ISO16000-19First edition2012-06-01Indoor air — Part 19: Sampling strategy for moulds Air intérieur — Partie 19: Stratégie d'échantillonnage des moisissures
oSIST ISO 16000-19:2013



ISO 16000-19:2012(E)
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56  CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2012 – All rights reserved
oSIST ISO 16000-19:2013



ISO 16000-19:2012(E) © ISO 2012 – All rights reserved iii Contents Page Foreword . iv Introduction . vi 1 Scope . 1 2 Normative references . 1 3 Terms and definitions . 1 4 Properties, origin and occurrence of moulds in indoor environments . 4 5 Sampling and detection methods . 5 6 Measurement strategy . 6 6.1 General aspects . 6 6.2 Selection of appropriate procedure . 9 7 Quality requirements and uncertainty considerations . 17 Annex A (informative)
Moisture damage indicators . 18 Annex B (informative)
Devices for total spore count and detection of culturable fungi . 19 Annex C (informative)
Field inspection report to describe sampling procedure and to document potential mould damage . 21 Bibliography . 27
oSIST ISO 16000-19:2013



ISO 16000-19:2012(E) iv © ISO 2012 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent r
...

SLOVENSKI STANDARD
SIST ISO 16000-19:2014
01-junij-2014
1RWUDQML]UDNGHO6WUDWHJLMDY]RUþHQMDJOLY
Indoor air - Part 19: Sampling strategy for moulds
Air intérieur - Partie 19: Stratégie d'échantillonnage des moisissures
Ta slovenski standard je istoveten z: ISO 16000-19:2012
ICS:
13.040.20 Kakovost okoljskega zraka Ambient atmospheres
SIST ISO 16000-19:2014 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 16000-19:2014

---------------------- Page: 2 ----------------------

SIST ISO 16000-19:2014

INTERNATIONAL ISO
STANDARD 16000-19
First edition
2012-06-01


Indoor air —
Part 19:
Sampling strategy for moulds
Air intérieur —
Partie 19: Stratégie d'échantillonnage des moisissures




Reference number
ISO 16000-19:2012(E)
©
ISO 2012

---------------------- Page: 3 ----------------------

SIST ISO 16000-19:2014
ISO 16000-19:2012(E)

COPYRIGHT PROTECTED DOCUMENT


©  ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2012 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 16000-19:2014
ISO 16000-19:2012(E)
Contents Page
Foreword . iv
Introduction . vi
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Properties, origin and occurrence of moulds in indoor environments . 4
5  Sampling and detection methods . 5
6  Measurement strategy . 6
6.1  General aspects . 6
6.2  Selection of appropriate procedure . 9
7  Quality requirements and uncertainty considerations . 17
Annex A (informative) Moisture damage indicators . 18
Annex B (informative) Devices for total spore count and detection of culturable fungi . 19
Annex C (informative) Field inspection report to describe sampling procedure and to document
potential mould damage . 21
Bibliography . 27

© ISO 2012 – All rights reserved iii

---------------------- Page: 5 ----------------------

SIST ISO 16000-19:2014
ISO 16000-19:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Stand
...

INTERNATIONAL ISO
STANDARD 16000-19
First edition
2012-06-01


Indoor air —
Part 19:
Sampling strategy for moulds
Air intérieur —
Partie 19: Stratégie d'échantillonnage des moisissures




Reference number
ISO 16000-19:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 16000-19:2012(E)

COPYRIGHT PROTECTED DOCUMENT


©  ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 16000-19:2012(E)
Contents Page
Foreword . iv
Introduction . vi
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Properties, origin and occurrence of moulds in indoor environments . 4
5  Sampling and detection methods . 5
6  Measurement strategy . 6
6.1  General aspects . 6
6.2  Selection of appropriate procedure . 9
7  Quality requirements and uncertainty considerations . 17
Annex A (informative) Moisture damage indicators . 18
Annex B (informative) Devices for total spore count and detection of culturable fungi . 19
Annex C (informative) Field inspection report to describe sampling procedure and to document
potential mould damage . 21
Bibliography . 27

© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 16000-19:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16000-19 was prepared by Technical Committee ISO/TC 146, Air quality, Subcommittee SC 6, Indoor air.
ISO 16000 consists of the following parts, under the general title Indoor air:
 Part 1: General aspects of sampling strategy
 Part 2: Sampling strategy for formaldehyde
 Part 3:
...

NORME ISO
INTERNATIONALE 16000-19
Première édition
2012-06-01



Air intérieur —
Partie 19:
Stratégie d'échantillonnage des
moisissures
Indoor air —
Part 19: Sampling strategy for moulds




Numéro de référence
ISO 16000-19:2012(F)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 16000-19:2012(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT


©  ISO 2012
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2012 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 16000-19:2012(F)
Sommaire Page
Avant-propos . iv
Introduction . vi
1  Domaine d'application . 1
2  Références normatives . 1
3  Termes et définitions . 1
4  Propriétés, origine et occurrence des moisissures dans les environnements intérieurs . 4
5  Méthodes d'échantillonnage et de détection . 6
6  Stratégie de mesurage . 6
6.1  Aspects généraux . 6
6.2  Sélection d'un mode opératoire approprié . 10
7  Exigences de qualité et considérations relatives à l'incertitude . 19
Annexe A (informative) Indicateurs de dommage de moisissure . 20
Annexe B (informative) Dispositifs de détermination du nombre total de spores et de détection
des champignons cultivables . 21
Annexe C (informative) Rapport d'inspection sur le terrain pour décrire un mode opératoire de
prélèvement et pour documenter un dommage de moisissure potentiel . 23
Bibliographie . 29

© ISO 2012 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 16000-19:2012(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 16000-19 a été élaborée par le comité technique ISO/TC 146, Qualité de l'air, sous-comité S
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.