ISO/IEC 24769-62:2015

INTERNATIONAL ISO/IEC
STANDARD 24769-62
First edition
2015-10-01
Information Technology — Real
Time Locating System (RTLS) Device
Conformance Test Methods —
Part 62:
High rate pulse repetition frequency
Ultra Wide Band (UWB) air interface
Technologies de l’information — Méthodes d’essai de conformité du
dispositif des systèmes de localisation en temps réel (RTLS) —
Partie 62: Méthodologie de test de interface aérienne ultra large
bande (UWB) à impulsions haute fréquence de répétition
Reference number
©
ISO/IEC 2015
© ISO/IEC 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO/IEC 2015 – All rights reserved

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms . 1
3.1 Terms and definitions . 1
3.2 Abbreviated terms . 1
4 Conformance tests for ISO/IEC 24730-62. 2
4.1 General . 2
4.2 Default conditions applicable to the test methods . 2
4.2.1 Preface . 2
4.2.2 Test environment . 2
4.2.3 Default tolerance . 2
4.2.4 Noise floor at test location. 2
4.2.5 Total measurement uncertainty . 3
4.3 UWB RF transmission tests . 3
4.3.1 General. 3
4.3.2 Test Objective . 3
4.3.3 Test procedure . 3
4.3.4 Test measurements and requirements . 4
4.3.5 Test report . 4
4.4 Receiver UWB RF tests . 4
4.4.1 Preface . 4
4.4.2 General. 4
4.4.3 Test objective . 5
4.4.4 Test procedure . 5
4.4.5 Test measurements and requirements . 5
4.4.6 Test report . 5
Annex A (normative) RF test measurement site. 6
© ISO/IEC 2015 – All rights reserved iii

Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are
members of ISO or IEC participate in the development of International Standards through technical
committees established by the respective organization to deal with particular fields of technical
activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international
organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the
work. In the field of information technology, ISO and IEC have established a joint technical committee,
ISO/IEC JTC 1.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for
the different types of document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject
of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent
rights. Details of any patent rights identified during the development of the document will be in the
Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT), see the following URL: Foreword — Supplementary information.
The committee responsible for this document is ISO/IEC JTC 1, Information technology, Subcommittee
SC 31, Automatic identification and data capture techniques.
ISO/IEC 24769 consists of the following parts, under the general title Information technology — Real-
time locating systems (RTLS) device conformance test methods:
— Part 2: Test methods for air interface communication at 2,4 GHz
— Part 5: Test methods for chirp spread spectrum (CSS) at 2,4 GHz air interface
— Part 61: Low rate pulse repetition frequency Ultra Wide Band (UWB) air interface
— Part 62: High rate pulse repetition frequency Ultra Wide Band (UWB) air interface
iv © ISO/IEC 2015 – All rights reserved

Introduction
ISO/IEC 24730-62 defines an air interface for ultra wide band (UWB) Real Time Locating Systems
(RTLS) devices used in asset management applications.
This International Standard contains all measurements required to be made on a product in order to
establish whether it conforms to ISO/IEC 24730-62.
Test methods for measuring performance of equipment compliant with ISO/IEC 24730-62 are given in
ISO/IEC 24770-62.
© ISO/IEC 2015 – All rights reserved v

INTERNATIONAL STANDARD ISO/IEC 24769-62:2015(E)
Information Technology — Real Time Locating System
(RTLS) Device Conformance Test Methods —
Part 62:
High rate pulse repetition frequency Ultra Wide Band
(UW
...