ISO/IEC 15459-3:2006

INTERNATIONAL ISO/IEC
STANDARD 15459-3
First edition
2006-03-01

Information technology — Unique
identifiers —
Part 3:
Common rules for unique identifiers
Technologies de l'information — Identificateurs uniques —
Partie 3: Règles communes pour les identificateurs uniques




Reference number
ISO/IEC 15459-3:2006(E)
©
ISO/IEC 2006

---------------------- Page: 1 ----------------------
ISO/IEC 15459-3:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO/IEC 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO/IEC 2006 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 15459-3:2006(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 15459-3 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 31, Automatic identification and data capture techniques.
Because the scope of ISO/IEC 15459 has been expanded beyond transport units, the term “license plate” in
the first edition of ISO/IEC 15459 has been replaced by “unique identifier” in the second edition.
ISO/IEC 15459 consists of the following parts, under the general title Information technology — Unique
identifiers:
⎯ Part 1: Unique identifiers for transport units
⎯ Part 2: Registration procedures
⎯ Part 3: Common rules for unique identifiers
⎯ Part 4: Unique identifiers for supply chain management
© ISO/IEC 2006 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC 15459-3:2006(E)
Introduction
Unique identification can occur at many different levels in the supply chain, at the transport unit, at the item
level, and elsewhere. Such distinct entities are often handled by several parties: the sender, the receiver, one
or more carriers, customs authorities, etc. Each of these parties must be able to identify and trace the item so
that reference can be made to associated information such as configuration, maintenance history, address,
order number, contents of the item, weight, sender, batch or lot number, etc.
The information is often held on computer systems, and may be exchanged between parties involved via EDI
(Electronic Data Interchange) and XML (eXtensible Markup Language) messages.
There are considerable benefits if the identity of the item is represented in bar code format, or other AIDC
(Automatic Identification and Data Capture) media and attached to or made a constituent part of that which is
being uniquely identified so that
⎯ it can be read electronically, thus minimising errors;
⎯ one identity can be used by all parties;
⎯ each party can use the identity to look up its computer files to find the data associated with the item;
⎯ the identifier is unique within the class and cannot appear on any other item of the class during the
lifetime of the item.
The common rules for unique identifiers for item management are defined in this part of ISO/IEC 15459.

iv © ISO/IEC 2006 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO/IEC 15459-3:2006(E)

Information technology — Unique identifiers —
Part 3:
Common rules for unique identifiers
1 Scope
This part of ISO/IEC 15459 specifies the common rules that apply for unique identifiers for item management
that are required to ensure full compatibility across classes of unique identifiers.
2 Normative references
The following refere
...