IEC 62475:2010
(Main)High-current test techniques - Definitions and requirements for test currents and measuring systems
High-current test techniques - Definitions and requirements for test currents and measuring systems
IEC 62475:2010 is applicable to high-current testing and measurements on both high-voltage and low-voltage equipment. It deals with steady-state and short-time direct current (as e.g. encountered in high-power d.c. testing), steady-state and short-time alternating current (as e.g. encountered in high-power a.c. testing), and impulse-current. In general, currents above 100 A are considered in this International Standard, although currents less than this can occur in tests. This standard also covers fault detection during, for example, lightning impulse testing.
Techniques des essais à haute intensité - Définitions et exigences relatives aux courants d'essai et systèmes de mesure
La CEI 62475:2010 s'applique aux essais et mesures à haute intensité sur des matériels haute et basse tensions. Elle couvre les essais à haute intensité en courant continu et courant alternatif en régime établi et de courte durée ainsi que des essais de courant de choc. De manière générale, la présente Norme internationale prend en compte des courants de plus de 100 A, même si des intensités moindres peuvent apparaître dans les essais. La présente norme couvre également la détection de défauts, comme par exemple dans le cadre d'essais aux chocs de foudre.
General Information
Standards Content (Sample)
IEC 62475 ®
Edition 1.0 2010-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
High-current test techniques – Definitions and requirements for test currents
and measuring systems
Techniques des essais à haute intensité – Définitions et exigences relatives
aux courants d'essai et systèmes de mesure
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 62475 ®
Edition 1.0 2010-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
High-current test techniques – Definitions and requirements for test currents
and measuring systems
Techniques des essais à haute intensité – Définitions et exigences relatives
aux courants d'essai et systèmes de mesure
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
XE
CODE PRIX
ICS 19.080 ISBN 978-2-88912-184-7
– 2 – 62475 © IEC:2010
CONTENTS
FOREWORD.8
1 Scope.10
2 Normative references .10
3 Terms and definitions .10
3.1 Measuring systems.11
3.2 Components of a measuring system .11
3.3 Scale factors .12
3.4 Rated values .13
3.5 Definitions related to the dynamic behaviour .13
3.6 Definitions related to uncertainty .14
3.7 Definitions related to tests on measuring systems .16
4 Procedures for qualification and use of a measuring system.17
4.1 General principles .17
4.2 Schedule of performance tests .17
4.3 Schedule of performance checks.17
4.4 Requirements for the record of performance.18
4.4.1 Contents of the record of performance.18
4.4.2 Exceptions.18
4.5 Operating conditions .18
4.6 Uncertainty.19
5 Tests and test requirements for an approved measuring system.20
5.1 General requirements.20
5.2 Calibration – Determination of the scale factor .20
5.2.1 Calibration of a measuring system by comparison with a reference
measuring system (preferred method) .20
5.2.2 Determination of the scale factor of a measuring system from those
of its components .24
5.3 Linearity test .25
5.3.1 Application .25
5.3.2 Alternative methods in order of suitability .26
5.4 Dynamic behaviour.26
5.5 Short-term stability .27
5.5.1 Method .27
5.5.2 Steady-state current .27
5.5.3 Impulse current and short-time current .28
5.5.4 Periodic impulse current and periodic short-time current.28
5.6 Long-term stability.29
5.7 Ambient temperature effect .29
5.8 Effect of nearby current paths .30
5.9 Software effect .32
5.10 Uncertainty calculation .32
5.10.1 General .32
5.10.2 Uncertainty of calibration .32
5.10.3 Uncertainty of measurement using an approved measuring system .33
5.11 Uncertainty calculation of time-parameter measurements (impulse currents
only).34
5.11.1 General .34
62475 © IEC:2010 – 3 –
5.11.2 Uncertainty of the time-parameter calibration.34
5.11.3 Uncertainty of a time-parameter measurement using an approved
measuring system .35
5.12 Interference test .36
5.12.1 Application .36
5.12.2 Current-converting shunts and current transformers with iron .37
5.12.3 Inductive measuring systems without iron (Rogowski coils) .38
5.13 Withstand tests .38
5.13.1 Voltage withstand tests.38
5.13.2 Current withstand tests.39
6 Steady-state direct current .39
6.1 Application .39
6.2 Terms and definitions .39
6.3 Test current.39
6.3.1 Requirements .39
6.3.2 Tolerances .39
6.4 Measurement of the test current .40
6.4.1 Requirements for an approved measuring system.40
6.4.2 Uncertainty contributions .40
6.4.3 Dynamic behaviour .40
6.4.4 Calibrations and tests on an approved measuring system.40
6.4.5 Performance check.41
6.5 Measurement of ripple amplitude.41
6.5.1 Requirements for an approved measuring system.41
6.5.2 Uncertainty contributions .41
6.5.3 Dynamic behaviour for ripple .41
6.5.4 Calibrations and tests on an approved ripple-current measuring
system.42
6.5.5 Measurement of the scale factor at the ripple frequency .42
6.5.6 Performance check for ripple current measuring system .42
6.6 Test procedures .43
7 Steady-state alternating current.43
7.1 Application .43
7.2 Terms and definitions .43
7.3 Test current.43
7.3.1 Requirements .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.